Inspections after Work on System Electrical Installation

TASK 05-51-43-700-001-A
Inspections after Work on System Electrical Installation

1. Reason for the Job
To give the list of all the inspections to do after work on the aircraft electrical installation (wiring, connectors, etc.).
The purpose of this inspection is not to do a check of all the aircraft functions but to make sure that:

Basic functions of the aircraft systems operate correctly.
There are no unwanted effects on the main functions of the systems not directly related to the work done.

NOTE: Only the inspections that are applicable to the system on which the work was done are necessary.

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
TASK 22-10-00-710-002-A	Operational Check of AP Disengagement and Locking Devices of Side Stick Controller and Rudder Pedals
TASK 22-30-00-710-003-A	Operational Check of Engine/Autothrust System Isolation
TASK 22-61-00-710-001-A	Operational Test of the Rudder-Travel Limiting Function
TASK 22-62-00-710-001-A	Operational Test of the Rudder Trim Function
TASK 22-63-00-710-001-A	Operational Test of the Yaw Damper Function
TASK 22-96-00-710-001-A	Operational Test of the AFS
TASK 22-97-00-710-001-A	Operational Test of the LAND CAT III Capability
TASK 24-00-00-710-003-A	Integrity Test of the Electrical Power
TASK 24-24-00-710-001-A	Operational Check of Emergency Generating System
TASK 24-24-00-710-002-A	Operational Test of the Emergency Generator Control Unit (GCU) through Centralized Fault Display System (CFDS)
TASK 24-38-00-710-001-A	Operational Test of the Battery Charge Limiter (BCL), (with the CFDS)
TASK 24-38-00-710-001-A-01	Operational Test of the Battery Charge Limiter (BCL), (without the CFDS)
TASK 24-41-00-740-002-B	Operational Check of the GAPCU via the CFDS
TASK 24-41-00-740-004-A	Operational Check of the GPCU via the CFDS
TASK 26-12-00-710-001-A	Operational Check of Loop/Squib
TASK 27-54-00-710-002-A	Operational Test of the Flap and Slat Systems
TASK 27-96-00-710-023-A	Integrity Test of the Flight Control System
TASK 29-00-00-710-001-A	Integrity Test of the Hydraulic Power
TASK 32-42-00-710-006-A	Integrity Test of the Braking System
TASK 32-51-00-710-002-A	Integrity Test of the Nose Wheel Steering System
TASK 34-10-00-710-007-A	Test of the Angle of Attack (AOA) Warning
TASK 34-13-00-710-006-A	Operational Test of the AOA SENSOR TEST
TASK 34-13-00-740-002-A	INTERFACE TEST of the ADR
TASK 34-13-00-740-003-A	SYSTEM TEST of the ADR
TASK 34-13-00-740-005-A	Read the CFDIU for the ADR INPUT STATUS
TASK 34-14-00-740-001-A	Interface Test of the IR
TASK 34-14-00-740-002-A	Read CFDIU for IR CURRENT STATUS
TASK 34-14-00-740-003-A	Read CFDIU for IR INPUT STATUS
TASK 71-00-00-710-001-A	Dry Motoring Check
TASK 71-00-00-710-001-B	Dry Motoring Check
TASK 71-00-00-710-045-A	Test No.1 : Dry Motor Leak Check
TASK 71-00-00-860-817-A	Motor the Engine (Dry Method)
TASK 73-21-00-710-806-A	Test No.7 - EEC Operation Test (Self Test)
TASK 73-21-60-720-040-A	Functional Test of the Electronic Control Unit (ECU)
TASK 73-21-60-720-040-B	Functional Test of the Electronic Control Unit (ECU)
TASK 73-22-34-710-040-A	Operational Test of the EEC
TASK 73-25-34-710-040-A	Operational Test of the Engine Interface Unit
TASK 73-25-34-710-042-A	Operational Test of the EIU with the CFDS
TASK 73-25-34-710-043-A	Operational Test of the Engine Interface Unit
TASK 73-25-34-710-802-A	Operational Test of the Engine Interface Unit (EIU) with the Centralized Fault Display System (CFDS)
TASK 74-00-00-710-040-A	Operational Test of the Ignition System
TASK 74-00-00-710-040-A-01	Operational Test of the Ignition System without CFDS
TASK 74-00-00-710-041-A	Operational Test of the Ignition System with the CFDS
TASK 74-00-00-710-041-A-01	Operational Test of the ignition System without the CFDS
TASK 74-00-00-710-043-A	Operational Test of the Ignition System
TASK 74-00-00-710-043-A-01	Operational Test of the Ignition System without CFDS
TASK 74-00-00-710-802-A	Operational Test of the Ignition System with the CFDS
TASK 77-32-34-710-040-A	Operational Check of EVMU through CFDS for Advisory Indication on ECAM
TASK 77-32-34-710-040-B	Operational Check of EVMU through CFDS for Advisory Indication on ECAM
TASK 77-32-34-710-041-A	Operational Check of EVMU through CFDS
TASK 78-31-00-710-040-A	Operational Test of the Thrust Reverser System
TASK 78-31-00-710-040-A-01	Operational Test of the Thrust Reverser without CFDS - Engine not Running
TASK 78-31-00-710-040-A-02	Operational Test of the Thrust Reverser without CFDS - Engine Running
TASK 78-31-00-710-041-A	Operational Test of the Thrust Reverser System with the CFDS
TASK 78-31-00-710-041-A-02	Operational test of the Thrust Reverser without the CFDS and Engine Running
TASK 78-31-00-710-042-A	Operational Test of the Thrust Reverser System
TASK 78-31-00-710-805-A	Operational Test of Thrust Reverser with MCDU
TASK 78-31-00-710-805-A-01	Thrust Reverser Cycling Test (Engine Running)

3. Job Set-up
Subtask 05-51-43-869-050-A

A. Not Applicable

4. Procedure
Subtask 05-51-43-710-051-B

A. Do these inspections to make sure that the basic functions of the AUTO FLIGHT system operate correctly:
(1) Operational test of autopilot disengagement and locking devices of the side stick controller and rudder pedals (Ref. AMM TASK 22-10-00-710-002).
(2) Operational test of the engine/autothrust system isolation:

With AIDS installed (Ref. AMM TASK 22-30-00-710-003)
With AIDS not installed (Ref. AMM D/O 22-30-00-72).

(3) Operational test of the rudder travel limiting function (Ref. AMM TASK 22-61-00-710-001).
(4) Operational test of the rudder trim function (Ref. AMM TASK 22-62-00-710-001).
(5) Operational test of the yaw damper function (Ref. AMM TASK 22-63-00-710-001).
(6) Operational test of the AFS (Ref. AMM TASK 22-96-00-710-001).
(7) Operational test of the LAND CAT III capability (Ref. AMM TASK 22-97-00-710-001).

Subtask 05-51-43-710-052-A ** ON A/C NOT FOR ALL

B. Do these inspections to make sure that the basic functions of the ELECTRICAL POWER system operate correctly:
(1) Integrity test of the electrical power (Ref. AMM TASK 24-00-00-710-003).
(2) Operational test of the emergency generation system (Ref. AMM TASK 24-24-00-710-001).
(3) Operational test of the Emergency Generator Control Unit (GCU) from the Centralized Fault Display System (CFDS) (Ref. AMM TASK 24-24-00-710-002).
(4) Operational test of the Battery Charge Limiter (BCL) (with the CFDS) (Ref. AMM TASK 24-38-00-710-001).
(5) Operational test of the Ground Power Control Unit (GPCU) (Ref. AMM TASK 24-41-00-740-004).

Subtask 05-51-43-710-052-H ** ON A/C NOT FOR ALL

B. Do these inspections to make sure that the basic functions of the ELECTRICAL POWER system operate correctly:
(1) Integrity test of the electrical power (Ref. AMM TASK 24-00-00-710-003).
(2) Operational test of the emergency generation system (Ref. AMM TASK 24-24-00-710-001).
(3) Operational test of the Emergency Generator Control Unit (GCU) from the Centralized Fault Display System (CFDS) (Ref. AMM TASK 24-24-00-710-002).
(4) Operational test of the Battery Charge Limiter (BCL) (with the CFDS) (Ref. AMM TASK 24-38-00-710-001).
(5) Operational test of the Ground Auxiliary Power Control Unit (GAPCU) (Ref. AMM TASK 24-41-00-740-002).

Subtask 05-51-43-710-053-A

C. Do these inspections to make sure that the basic functions of the FIRE PROTECTION system operate correctly:
(1) Operational test of the engine fire and overheat detection (Ref. AMM TASK 26-12-00-710-001).

Subtask 05-51-43-710-054-A

D. Do these inspections to make sure that the basic functions of the FLIGHT CONTROLS system operate correctly:
(1) Operational test of the flap and slat systems (Ref. AMM TASK 27-54-00-710-002).
(2) Integrity test of the flight control system (Ref. AMM TASK 27-96-00-710-023).

Subtask 05-51-43-710-055-A

E. Do these inspections to make sure that the basic functions of the HYDRAULIC POWER system operate correctly:
(1) Integrity test of the hydraulic power (Ref. AMM TASK 29-00-00-710-001).

Subtask 05-51-43-710-056-A

F. Do these inspections to make sure that the basic functions of the LANDING GEAR system operate correctly:
(1) Integrity test of the braking system (Ref. AMM TASK 32-42-00-710-006).
(2) Integrity test of the nose wheel steering system (Ref. AMM TASK 32-51-00-710-002).

Subtask 05-51-43-710-057-A

G. Do these inspections to make sure that the basic functions of the NAVIGATION system operate correctly:
(1) Test of the angle-of-attack warning (Ref. AMM TASK 34-10-00-710-007).
(2) Operational test of the AOA SENSOR TEST (Ref. AMM TASK 34-13-00-710-006).
(3) INTERFACE TEST of the ADR (Ref. AMM TASK 34-13-00-740-002).
(4) ADR status:

For the SYSTEM TEST of the ADR (Ref. AMM TASK 34-13-00-740-003) or
Read the CFDIU for ADR CURRENT STATUS (Ref. AMM D/O 34-13-00-74) or
Read the CFDIU for ADR INPUT STATUS (Ref. AMM TASK 34-13-00-740-005).

(5) Interface test of the IR (Ref. AMM TASK 34-14-00-740-001).
(6) IR status:

Read the CFDIU for IR CURRENT STATUS (Ref. AMM TASK 34-14-00-740-002) or
Read the CFDIU for IR INPUT STATUS (Ref. AMM TASK 34-14-00-740-003).

Subtask 05-51-43-710-058-A ** ON A/C NOT FOR ALL

H. Do these inspections to make sure that the basic functions of the ENGINE systems operate correctly:
(1) Operational test of the thrust reverser system (Ref. AMM TASK 78-31-00-710-040).
(2) Operational test of the ignition system (Ref. AMM TASK 74-00-00-710-040).
(3) Operational test of the Engine Interface Unit (EIU) (1KS1, 1KS2) (Ref. AMM TASK 73-25-34-710-040).
(4) Functional test of the Electronic Control Unit (ECU) (Ref. AMM TASK 73-21-60-720-040).
(5) Operational test of the Engine Vibration Monitoring Unit (EVMU) through the CFDS (Ref. AMM TASK 77-32-34-710-040).
(6) Dry-motoring check (Ref. AMM TASK 71-00-00-710-001).

Subtask 05-51-43-710-058-B ** ON A/C NOT FOR ALL

H. Do these inspections to make sure that the basic functions of the ENGINE systems operate correctly:
(1) Operational test of the thrust reverser system (Ref. AMM TASK 78-31-00-710-042).
(2) Operational test of the ignition system (Ref. AMM TASK 74-00-00-710-043).
(3) Operational test of the Engine Interface Unit (EIU) (Ref. AMM TASK 73-25-34-710-043).
(4) Functional test of the Electronic Control Unit (ECU) (Ref. AMM TASK 73-21-60-720-040).
(5) Operational test of the Engine Vibration Monitoring Unit (EVMU) through the CFDS (Ref. AMM TASK 77-32-34-710-040).
(6) Dry-motoring check (Ref. AMM TASK 71-00-00-710-001).

Subtask 05-51-43-710-058-C ** ON A/C NOT FOR ALL

H. Do these inspections to make sure that the basic functions of the ENGINE systems operate correctly:
(1) Operational test of the thrust reverser system with the CFDS (Ref. AMM TASK 78-31-00-710-041).
(2) Operational test of the ignition system with the CFDS (Ref. AMM TASK 74-00-00-710-041).
(3) Operational test of the Engine Interface Unit (EIU) with the CFDS (Ref. AMM TASK 73-25-34-710-042).
(4) Operational test of the Engine Electronic Control (EEC) (Ref. AMM TASK 73-22-34-710-040).
(5) Operational test of the Engine Vibration Monitoring Unit (EVMU) through the CFDS (Ref. AMM TASK 77-32-34-710-041).
(6) Test No.1: dry motor leak check (Ref. AMM TASK 71-00-00-710-045).

Subtask 05-51-43-710-058-E ** ON A/C NOT FOR ALL

H. Do these inspections to make sure that the basic functions of the ENGINE systems operate correctly:
(1) Operational test of the thrust-reverser door-opening system (Ref. AMM TASK 78-31-00-710-805).
(2) Operational test of the ignition system with the CFDS (Ref. AMM TASK 74-00-00-710-802).
(3) Operational test of the Engine Interface Unit (EIU) with the CFDS (Ref. AMM TASK 73-25-34-710-802).
(4) Operational test of the Electronic Engine Control (EEC) (Ref. AMM TASK 73-21-00-710-806).
(5) Dry-motor the engine (Ref. AMM TASK 71-00-00-860-817).

[Rev.10 from 2021] 2026.03.31 22:52:01 UTC