W DOC AIRBUS | AMM A320F

Integrity Test of the Flight Control System

TASK 27-96-00-710-023-A
Integrity Test of the Flight Control System

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
ZONE: 210
1. Reason for the Job
To do an integrity test of the flight control system after maintenance operation on system electrical installation.
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
210
CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD
822
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 24-41-00-861-002-A
Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01
Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02
Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A
De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01
De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02
De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 27-96-00-740-001-A
BITE Test of the EFCS (Ground Scanning)
TASK 29-10-00-863-001-A
Pressurize the Green Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-002-A
Pressurize the Yellow Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-003-A
Pressurize the Blue Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-003-A-01
Pressurize the Blue Hydraulic System with the Blue Electric Pump
TASK 29-10-00-864-003-A
Depressurize the Blue Hydraulic System
TASK 29-23-00-864-001-A
Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU
TASK 29-24-00-864-001-A
Depressurize the Yellow Hydraulic System
TASK 31-60-00-860-001-A
EIS Start Procedure
TASK 31-60-00-860-002-A
EIS Stop Procedure
3. Job Set-up
Subtask 27-96-00-860-090-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
   (1) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).
   (2) On the overhead panel 23VU:
  • Make sure that the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC 1 pushbutton switches are pushed (on these pushbutton switches, the OFF and FAULT legends are off).
   (3) On the overhead panel 24VU:
  • Make sure that the FLT CTL/ELAC 2, FLT CTL/SEC 2, FLT CTL/SEC 3 and FAC 2 pushbutton switches are pushed (on these pushbutton switches, the OFF and FAULT legends are off).
   (4) On the overhead panel 20VU, on the ADIRS CDU:
  • Set the three OFF/NAV/ATT selector switches to NAV.
   (5) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
   (6) On the center pedestal, on the ECAM control panel, push:
  • the CLR key until all the warnings (if any) stop
  • the F/CTL key (on the lower ECAM display unit, the F/CTL page comes into view).
   (7) Pressurize the Green, Yellow and Blue hydraulic systems (Ref. AMM TASK 29-10-00-863-001) (Ref. AMM TASK 29-10-00-863-002) (Ref. AMM TASK 29-10-00-863-003).
Subtask 27-96-00-860-090-B ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
   (1) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).
   (2) On the overhead panel 23VU:
  • Make sure that the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC 1 pushbutton switches are pushed (on these pushbutton switches, the OFF and FAULT legends are off).
   (3) On the overhead panel 24VU:
  • Make sure that the FLT CTL/ELAC 2, FLT CTL/SEC 2, FLT CTL/SEC 3 and FAC 2 pushbutton switches are pushed (on these pushbutton switches, the OFF and FAULT legends are off).
   (4) On the overhead panel 41VU, on the ADIRS MSU:
  • Set the three OFF/NAV/ATT selector switches to NAV.
   (5) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
   (6) On the center pedestal, on the ECAM control panel, push:
  • the CLR key until all the warnings (if any) stop
  • the F/CTL key (on the lower ECAM display unit, the F/CTL page comes into view).
   (7) Pressurize the Green, Yellow and Blue hydraulic systems (Ref. AMM TASK 29-10-00-863-001) (Ref. AMM TASK 29-10-00-863-002) (Ref. AMM TASK 29-10-00-863-003).
Subtask 27-96-00-010-067-A
B. Get Access
   (1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE > in position at the access door 822.
   (2) Open the access door 822.
   (3) On the battery power center 105VU:
  • loosen the two screws and remove the protective cover.
Subtask 27-96-00-865-089-A
C. Make sure that this(these) circuit breaker(s) is(are) closed:
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B11
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B09
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B08
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B06
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B04
49VUFLIGHT CONTROLS/SEC1/NORM/SPLY21CE1B03
** ON A/C ALL
105VUFLIGHT CONTROLS/ELAC2/STBY SPLY16CE2A02
105VUFLT CTL/ELAC1/STBY SPLY16CE1A01
105VUFLT CTL/SEC1/STBY SPLY22CEB01
121VUFLIGHT CONTROLS/SEC3/SPLY21CE3Q19
121VUFLIGHT CONTROLS/SEC2/SPLY21CE2Q18
121VUFLIGHT CONTROLS/THS ACTR/MOT319CE3Q17
121VUFLIGHT CONTROLS/THS ACTR/MOT119CE1Q16
121VUFLIGHT CONTROLS/ELAC2/NORM/SPLY15CE2R20
4. Procedure
Subtask 27-96-00-710-080-A ** ON A/C NOT FOR ALL
A. Integrity Test of the Flight Control System

During the test, ignore the MASTER CAUT light and the single chime.
ACTION
RESULT
1.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 and FAC 1 pushbutton switches.
On the overhead panel 23VU:
  • the OFF legends of the FLT CTL/SEC 1 and FAC 1 pushbutton switches come on.
2.On the overhead panel 24VU:
  • release the FLT CTL/ELAC 2, FLT CTL/SEC 2, FLT CTL/SEC 3 and FAC 2 pushbutton switches.
On the overhead panel 24VU:
  • the OFF legends of the FLT CTL/ELAC 2, FLT CTL/SEC 2, FLT CTL/SEC 3 and FAC 2 pushbutton switches come on.
3.On the CAPT side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves up, the index of the left aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
  • move the side stick to the left until it touches the stop.
  • the index of the left aileron moves up, the index of the right aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
4.On the F/O side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves up, the index of the left aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
  • move the side stick to the left until it touches the stop.
  • the index of the left aileron moves up, the index of the right aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
5.On the overhead panel 24VU:
  • push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
6.On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
7.On the CAPT side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves up, the index of the left aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
  • move the side stick to the left until it touches the stop.
  • the index of the left aileron moves up, the index of the right aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
8.On the F/O side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves up, the index of the left aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
  • move the side stick to the left until it touches the stop.
  • the index of the left aileron moves up, the index of the right aileron moves down.
  • release the side stick.
  • the indexes of the left and right ailerons move to the neutral position.
9.On the overhead panel 23VU:
  • push the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch goes off.
10.On the overhead panel 24VU:
  • push the FLT CTL/SEC 2 and FLT CTL/SEC 3 pushbutton switches.
  • release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legends of the FLT CTL/SEC 2 and SEC 3 pushbutton switches go off.
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
11.On the CAPT side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
  • release the side stick.
  • the indexes of the spoilers 2, 3, 4, 5 on the right side go out of view (spoilers retracted).
  • move the side stick to the left until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
  • release the side stick.
  • the indexes of the spoilers 2, 3, 4, 5 on the left side go out of view (spoilers retracted).
12.On the F/O side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
  • release the side stick.
  • the indexes of the spoilers 2, 3, 4, 5 on the right side go out of view (spoilers retracted).
  • move the side stick to the left until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
  • release the side stick.
  • the indexes of the spoilers 2, 3, 4, 5 on the left side go out of view (spoilers retracted).
13.On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch goes off.
14.On the overhead panel 24VU:
  • push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
15.On the CAPT or F/O side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves up.
  • the index of the left aileron moves down.
  • the indexes of the spoilers 4, 5 on the right side come into view (spoilers extended).
16.On the CAPT or F/O side:
  • move the side stick to the left until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves down.
  • the index of the left aileron moves up.
  • the indexes of the spoilers 4, 5 on the left side come into view (spoilers extended).
17.On the CAPT or F/O side:
  • release the side stick.
On the lower ECAM display unit
  • the indexes of the right and left ailerons move to the neutral position.
  • the indexes of the spoilers 4, 5 go out of view (spoilers retracted).
18.On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
19.On the overhead panel 24VU:
  • release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
20.On the center pedestal:
  • put the speedbrake control lever in the FULL position.
On the lower ECAM display unit:
  • the indexes of the left and right spoilers 1, 2, 3 and 4 come into view (spoilers extended).
  • put the speedbrake control lever in the RET position.
  • the indexes of the left and right spoilers 1, 2, 3 and 4 go out of view (spoilers retracted).
21.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
22.On the overhead panel 24VU:
  • release the FLT CTL/SEC 2 and FLT CTL/SEC 3 pushbutton switches.
On the overhead panel 24VU:
  • the OFF legends of the FLT CTL/SEC 2 and FLT CTL/SEC 3 pushbutton switches come on.
23.On the center pedestal:
  • put the slat and flap control lever in position 1.
  • manually set the THS control wheel to 13 degrees nose-up.

24.On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1 pushbutton switch.
The THS goes to the zero position.
25.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
26.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
27.On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
28.On the overhead panel 24VU:
  • push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
29.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
30.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
31.On the overhead panel 23VU:
  • push the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch goes off.
32.On the overhead panel 24VU:
  • release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
33.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
34.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
35.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
36.On the overhead panel 24VU:
  • push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.
37.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
38.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
39.On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1 and SEC 1 pushbutton switches.
On the overhead panel 23VU:
  • the OFF legends of the FLT CTL/ELAC 1 and FLT CTL/SEC 1 pushbutton switches go off.
40.On the overhead panel 24VU:
  • push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
41.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
42.On the overhead panel 24VU:
  • release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
43.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
44.On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
45.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
46.On the overhead panel 24VU:
  • release the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.
47.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
48.On the maintenance panel 50VU:
  • release the HYD LEAK MEASUREMENT VALVES/B pushbutton switch.
On the maintenance panel 50VU:
  • the OFF legend of the HYD LEAK MEASUREMENT VALVES/B pushbutton switch comes on.
49.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators stay in neutral position.
  • release the side stick.
  • the indexes of the elevators stay in neutral position.
50.On the maintenance panel 50VU:
  • push the HYD LEAK MEASUREMENT VALVES/B pushbutton switch.
On the maintenance panel 50VU:
  • the OFF legend of the HYD LEAK MEASUREMENT VALVES/B pushbutton switch goes off.
51.On the overhead panel 24VU:
  • push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.
52.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
53.On the maintenance panel 50VU:
  • release the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches.
On the maintenance panel 50VU:
  • the OFF legends of the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches come on.
54.On the CAPT side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators stay in neutral position.
  • release the side stick.
  • the indexes of the elevators stay in neutral position.
55.On the maintenance panel 50VU:
  • push the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches.
On the maintenance panel 50VU:
  • the OFF legends of the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches go off.
56.On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1 and SEC 1 pushbutton switches.
On the overhead panel 23VU:
  • the OFF legends of the FLT CTL/ELAC 1 and FLT CTL/SEC 1 pushbutton switches go off.
57.On the overhead panel 24VU:
  • push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
58.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
59.On the overhead panel 24VU:
  • release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
60.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
61.On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
62.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
63.On the overhead panel 24VU:
  • release the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.
64.On the F/O side:
  • move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • the indexes of the elevators move up.
  • move the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
65.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
66.On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC 1 pushbutton switches.
On the overhead panel 23VU:
  • the OFF legends of the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC 1 pushbutton switches go off.
67.On the overhead panel 23VU:
  • release the FAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FAC 1 pushbutton switch comes on.
68.On the overhead panel 24VU:
  • push the FAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FAC 2 pushbutton switch goes off.

On the CAPT or F/O PFD:
  • green dashes are shown.
69.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
70.On the overhead panel 24VU:
  • push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.

On the CAPT or F/O PFD:
  • green dashes are shown.
71.On the overhead panel 24VU:
  • push the FLT CTL/SEC 3 pushbutton switch.
  • release the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 3 pushbutton switch goes off.
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.

On the CAPT or F/O PFD:
  • green dashes are shown.
72.On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch.
  • push the FLT CTL/SEC 1 and FAC 1 pushbutton switches.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
  • the OFF legends of the FLT CTL/SEC 1 and FAC 1 pushbutton switches go off.
73.On the overhead panel 24VU:
  • push the FLT CTL/ELAC 2 pushbutton switch.
  • release the FLT CTL/SEC 3 and FAC 2 pushbutton switches.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
  • the OFF legends of the FLT CTL/SEC 3 and FAC 2 pushbutton switches come on.

On the CAPT or F/O PFD:
  • green dashes are shown.
74.On the overhead panel 23VU:
  • release the FAC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FAC 1 pushbutton switch comes on.
75.On the overhead panel 24VU:
  • push the FAC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FAC 2 pushbutton switch goes off.

On the PFD:
  • green dashes are shown.
76.On the overhead panel 23VU:
  • release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • the OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
77.On the overhead panel 24VU:
  • push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.

On the CAPT or F/O PFD:
  • green dashes are shown.
78.On the overhead panel 24VU:
  • release the FLT CTL/SEC 2 pushbutton switch.
  • push the FLT CTL/SEC 3 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.
  • the OFF legend of the FLT CTL/SEC 3 pushbutton switch goes off.

On the PFD:
  • green dashes are shown.
79.On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC1 pushbutton switches.
On the overhead panel 23VU:
  • the OFF legends of the FLT CTL/ELAC 1 FLT CTL/SEC 1 and FAC 1 pushbutton switches go off.
80.On the overhead panel 24VU:
  • push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • the OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.
81.On the CAPT side then on the F/O side:
  • move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • the index of the right aileron moves up, the index of the left aileron moves down.
  • the indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
  • release the side stick.
  • the indexes of the left and right ailerons go back to the neutral position.
  • move the side stick to the left until it touches the stop.
  • the index of the left aileron moves up, the index of the right aileron moves down.
  • the indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
  • release the side stick.
  • the indexes of the left and right ailerons go back to the neutral position.
  • pull the side stick rearward until it touches the stop.
  • the indexes of the elevators move up.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
  • push the side stick forward until it touches the stop.
  • the indexes of the elevators move down.
  • release the side stick.
  • the indexes of the elevators go back to the neutral position.
82.Do the BITE test of the EFCS1 or EFCS2 (Ref. AMM TASK 27-96-00-740-001)
On the MCDU, make sure that there is no maintenance message related to flight controls.
83.Do these steps:
  • On the CAPT side, move the side stick to the right and keep it in this position.
  • On the F/O side, move the side stick to the left and keep it in this position.
On the lower ECAM display unit:
  • all the surfaces stay in the neutral position.
84.On the F/O side, push the take-over and priority pushbutton switch.
On the lower ECAM display unit:
  • the right aileron moves down
  • the left aileron moves up
  • the left spoilers 2, 3, 4, 5 extend.
85.On the F/O side, release the take-over and priority pushbutton switch.
On the lower ECAM display unit, all the surfaces move to the neutral position.
86.On the CAPT side, push the take-over and priority pushbutton switch.
On the lower ECAM display unit, make sure that:
  • the right aileron moves up
  • the left aileron moves down
  • the right spoilers 2, 3, 4, 5 extend.
87.On the CAPT side, release the take-over and priority pushbutton switch.
On the lower ECAM display unit, all the surfaces move to the neutral position.
88.Release the CAPT and F/O side sticks.

Subtask 27-96-00-710-080-B ** ON A/C NOT FOR ALL
A. Integrity Test of the Flight Control System

During the test, ignore the MASTER CAUT light and the single chime.
ACTION
RESULT
1.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 and FAC 1 pushbutton switches.
On the overhead panel 23VU:
  • The OFF legends of the FLT CTL/SEC 1 and FAC 1 pushbutton switches come on.
2.On the overhead panel 24VU:
  • Release the FLT CTL/ELAC 2, FLT CTL/SEC 2, FLT CTL/SEC 3 and FAC 2 pushbutton switches.
On the overhead panel 24VU:
  • The OFF legends of the FLT CTL/ELAC 2, FLT CTL/SEC 2, FLT CTL/SEC 3 and FAC 2 pushbutton switches come on.
3.On the CAPT side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up, the index of the left aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
  • Move the side stick to the left until it touches the stop.
  • The index of the left aileron moves up, the index of the right aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
4.On the F/O side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up, the index of the left aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
  • Move the side stick to the left until it touches the stop.
  • The index of the left aileron moves up, the index of the right aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
5.On the overhead panel 24VU:
  • Push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
6.On the overhead panel 23VU:
  • Release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
7.On the CAPT side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up, the index of the left aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
  • Move the side stick to the left until it touches the stop.
  • The index of the left aileron moves up, the index of the right aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
8.On the F/O side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up, the index of the left aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
  • Move the side stick to the left until it touches the stop.
  • The index of the left aileron moves up, the index of the right aileron moves down.
  • Release the side stick.
  • The indexes of the left and right ailerons move to the neutral position.
9.On the overhead panel 23VU:
  • Push the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch goes off.
10.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 2 and FLT CTL/SEC 3 pushbutton switches.
  • Release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legends of the FLT CTL/SEC 2 and SEC 3 pushbutton switches go off.
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
11.On the CAPT side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
  • Release the side stick.
  • The indexes of the spoilers 2, 3, 4, 5 on the right side go out of view (spoilers retracted).
  • Move the side stick to the left until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
  • Release the side stick.
  • The indexes of the spoilers 2, 3, 4, 5 on the left side go out of view (spoilers retracted).
12.On the F/O side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
  • Release the side stick.
  • The indexes of the spoilers 2, 3, 4, 5 on the right side go out of view (spoilers retracted).
  • Move the side stick to the left until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
  • Release the side stick.
  • The indexes of the spoilers 2, 3, 4, 5 on the left side go out of view (spoilers retracted).
13.On the overhead panel 23VU:
  • Push the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch goes off.
14.On the overhead panel 24VU:
  • Push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
15.On the overhead panel 20VU:
  • Push the ADR 1 and ADR 2 pushbutton switches.
On the overhead panel 20VU:
  • The OFF legends of the ADR 1 and ADR 2 pushbutton switches go on.
16.On the CAPT of F/O side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up
  • The index of the left aileron moves down
  • The indexes of the spoilers 4, 5 on the right side come into view (spoilers extended).
17.On the CAPT or F/O side:
  • Move the side stick on the left until it touches the stop.
On the lower ECAM display unit:
  • The index of the left aileron moves up
  • The index of the right aileron moves down
  • The indexes of the spoilers 4, 5 on the left side come into view (spoilers extended).
18.On the CAPT or F/O side:
  • Release the side stick.
On the lower ECAM display unit:
  • The indexes of the right and left ailerons move to the neutral position
  • The indexes of the spoilers 4, 5 go out of view (spoilers retracted).
19.On the overhead panel 20VU:
  • Release the ADR 1 and ADR 2 pushbutton switches.
On the overhead panel 20VU:
  • The OFF legends of the ADR 1 and ADR 2 pushbutton switches go off.
20.On the CAPT or F/O side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up.
  • The index of the left aileron moves down.
  • The indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
21.On the CAPT or F/O side:
  • Move the side stick to the left until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves down.
  • The index of the left aileron moves up.
  • The indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
22.On the CAPT or F/O side:
  • Release the side stick.
On the lower ECAM display unit:
  • The indexes of the right and left ailerons move to the neutral position.
  • The indexes of the spoilers 2, 3, 4, 5 go out of view (spoilers retracted).
23.On the overhead panel 23VU:
  • Release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
24.On the overhead panel 24VU:
  • Release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
25.On the center pedestal:
  • Put the speedbrake control lever in the FULL position.
On the lower ECAM display unit:
  • The indexes of the left and right spoilers 1, 2, 3 and 4 come into view (spoilers extended).
  • Put the speedbrake control lever in the RET position.
  • The indexes of the left and right spoilers 1, 2, 3 and 4 go out of view (spoilers retracted).
26.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
27.On the overhead panel 24VU:
  • Release the FLT CTL/SEC 2 and FLT CTL/SEC 3 pushbutton switches.
On the overhead panel 24VU:
  • The OFF legends of the FLT CTL/SEC 2 and FLT CTL/SEC 3 pushbutton switches come on.
28.On the center pedestal:
  • Put the slat and flap control lever in position 1.
  • Manually set the THS control wheel to 13 degrees nose-up.

29.On the overhead panel 23VU:
  • Push the FLT CTL/ELAC 1 pushbutton switch.
The THS goes to the zero position.
30.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
31.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
32.On the overhead panel 23VU:
  • Release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
33.On the overhead panel 24VU:
  • Push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
34.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
35.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
36.On the overhead panel 23VU:
  • Push the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch goes off.
37.On the overhead panel 24VU:
  • Release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
38.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
39.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
40.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
41.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.
42.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
43.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
44.On the overhead panel 23VU:
  • Push the FLT CTL/ELAC 1 and SEC 1 pushbutton switches.
On the overhead panel 23VU:
  • The OFF legends of the FLT CTL/ELAC 1 and FLT CTL/SEC 1 pushbutton switches go off.
45.On the overhead panel 24VU:
  • Push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
46.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
47.On the overhead panel 24VU:
  • Release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
48.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
49.On the overhead panel 23VU:
  • Release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
50.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
51.On the overhead panel 24VU:
  • Release the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.
52.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
53.On the maintenance panel 50VU:
  • Release the HYD LEAK MEASUREMENT VALVES/B pushbutton switch.
On the maintenance panel 50VU:
  • The OFF legend of the HYD LEAK MEASUREMENT VALVES/B pushbutton switch comes on.
54.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators stay in neutral position.
  • Release the side stick.
  • The indexes of the elevators stay in neutral position.
55.On the maintenance panel 50VU:
  • Push the HYD LEAK MEASUREMENT VALVES/B pushbutton switch.
On the maintenance panel 50VU:
  • The OFF legend of the HYD LEAK MEASUREMENT VALVES/B pushbutton switch goes off.
56.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.
57.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
58.On the maintenance panel 50VU:
  • Release the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches.
On the maintenance panel 50VU:
  • The OFF legends of the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches come on.
59.On the CAPT side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators stay in neutral position.
  • Release the side stick.
  • The indexes of the elevators stay in neutral position.
60.On the maintenance panel 50VU:
  • Push the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches.
On the maintenance panel 50VU:
  • The OFF legends of the HYD LEAK MEASUREMENT VALVES/G and HYD LEAK MEASUREMENT VALVES/Y pushbutton switches go off.
61.On the overhead panel 23VU:
  • Push the FLT CTL/ELAC 1 and SEC 1 pushbutton switches.
On the overhead panel 23VU:
  • The OFF legends of the FLT CTL/ELAC 1 and FLT CTL/SEC 1 pushbutton switches go off.
62.On the overhead panel 24VU:
  • Push the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
63.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
64.On the overhead panel 24VU:
  • Release the FLT CTL/ELAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
65.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
66.On the overhead panel 23VU:
  • Release the FLT CTL/ELAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
67.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
68.On the overhead panel 24VU:
  • Release the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.
69.On the F/O side:
  • Move the side stick rearward until it touches the stop.
On the lower ECAM display unit:
  • The indexes of the elevators move up.
  • Move the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
70.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
71.On the overhead panel 23VU:
  • Push the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC 1 pushbutton switches.
On the overhead panel 23VU:
  • The OFF legends of the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC 1 pushbutton switches go off.
72.On the overhead panel 23VU:
  • Release the FAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FAC 1 pushbutton switch comes on.
73.On the overhead panel 24VU:
  • Push the FAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FAC 2 pushbutton switch goes off.

On the CAPT or F/O PFD:
  • Green dashes are shown.
74.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
75.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.

On the CAPT or F/O PFD:
  • Green dashes are shown.
76.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 3 pushbutton switch.
  • Release the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 3 pushbutton switch goes off.
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.

On the CAPT or F/O PFD:
  • Green dashes are shown.
77.On the overhead panel 23VU:
  • Release the FLT CTL/ELAC 1 pushbutton switch.
  • Push the FLT CTL/SEC 1 and FAC 1 pushbutton switches.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/ELAC 1 pushbutton switch comes on.
  • The OFF legends of the FLT CTL/SEC 1 and FAC 1 pushbutton switches go off.
78.On the overhead panel 24VU:
  • Push the FLT CTL/ELAC 2 pushbutton switch.
  • Release the FLT CTL/SEC 3 and FAC 2 pushbutton switches.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/ELAC 2 pushbutton switch goes off.
  • The OFF legends of the FLT CTL/SEC 3 and FAC 2 pushbutton switches come on.

On the CAPT or F/O PFD:
  • Green dashes are shown.
79.On the overhead panel 23VU:
  • Release the FAC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FAC 1 pushbutton switch comes on.
80.On the overhead panel 24VU:
  • Push the FAC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FAC 2 pushbutton switch goes off.

On the PFD:
  • Green dashes are shown.
81.On the overhead panel 23VU:
  • Release the FLT CTL/SEC 1 pushbutton switch.
On the overhead panel 23VU:
  • The OFF legend of the FLT CTL/SEC 1 pushbutton switch comes on.
82.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.

On the CAPT or F/O PFD:
  • Green dashes are shown.
83.On the overhead panel 24VU:
  • Release the FLT CTL/SEC 2 pushbutton switch.
  • Push the FLT CTL/SEC 3 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch comes on.
  • The OFF legend of the FLT CTL/SEC 3 pushbutton switch goes off.

On the PFD:
  • Green dashes are shown.
84.On the overhead panel 23VU:
  • Push the FLT CTL/ELAC 1, FLT CTL/SEC 1 and FAC1 pushbutton switches.
On the overhead panel 23VU:
  • The OFF legends of the FLT CTL/ELAC 1 FLT CTL/SEC 1 and FAC 1 pushbutton switches go off.
85.On the overhead panel 24VU:
  • Push the FLT CTL/SEC 2 pushbutton switch.
On the overhead panel 24VU:
  • The OFF legend of the FLT CTL/SEC 2 pushbutton switch goes off.
86.On the CAPT side then on the F/O side:
  • Move the side stick to the right until it touches the stop.
On the lower ECAM display unit:
  • The index of the right aileron moves up, the index of the left aileron moves down.
  • The indexes of the spoilers 2, 3, 4, 5 on the right side come into view (spoilers extended).
  • Release the side stick.
  • The indexes of the left and right ailerons go back to the neutral position.
  • Move the side stick to the left until it touches the stop.
  • The index of the left aileron moves up, the index of the right aileron moves down.
  • The indexes of the spoilers 2, 3, 4, 5 on the left side come into view (spoilers extended).
  • Release the side stick.
  • The indexes of the left and right ailerons go back to the neutral position.
  • Pull the side stick rearward until it touches the stop.
  • The indexes of the elevators move up.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
  • Push the side stick forward until it touches the stop.
  • The indexes of the elevators move down.
  • Release the side stick.
  • The indexes of the elevators go back to the neutral position.
87.Do the BITE test of the EFCS1 or EFCS2 (Ref. AMM TASK 27-96-00-740-001)
On the MCDU, make sure that there is no maintenance message related to flight controls.
88.Do these steps:
  • On the CAPT side, move the side stick to the right and keep it in this position.
  • On the F/O side, move the side stick to the left and keep it in this position.
On the lower ECAM display unit:
  • All the surfaces stay in the neutral position.
89.On the F/O side, push the take-over and priority pushbutton switch.
On the lower ECAM display unit:
  • The right aileron moves down
  • The left aileron moves up
  • The left spoilers 2, 3, 4, 5 extend.
90.On the F/O side, release the take-over and priority pushbutton switch.
On the lower ECAM display unit, all the surfaces move to the neutral position.
91.On the CAPT side, push the take-over and priority pushbutton switch.
On the lower ECAM display unit, make sure that:
  • The right aileron moves up
  • The left aileron moves down
  • The right spoilers 2, 3, 4, 5 extend.
92.On the CAPT side, release the take-over and priority pushbutton switch.
On the lower ECAM display unit, all the surfaces move to the neutral position.
93.Release the CAPT and F/O side sticks.

5. Close-up
Subtask 27-96-00-860-091-A ** ON A/C NOT FOR ALL
A. Put the aircraft back to the initial configuration
   (1) On the center pedestal, put the slat and flap control lever in fully retracted position.
   (2) Depressurize the aircraft hydraulic systems (Ref. AMM TASK 29-23-00-864-001) (Ref. AMM TASK 29-24-00-864-001) (Ref. AMM TASK 29-10-00-864-003).
   (3) On the overhead panel 20VU, on the ADIRS CDU:
  • set the three OFF/NAV/ATT selector switches to OFF.
   (4) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
   (5) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).
Subtask 27-96-00-860-091-B ** ON A/C NOT FOR ALL
A. Put the aircraft back to the initial configuration
   (1) On the center pedestal, put the slat and flap control lever in fully retracted position.
   (2) Depressurize the aircraft hydraulic systems (Ref. AMM TASK 29-23-00-864-001) (Ref. AMM TASK 29-24-00-864-001) (Ref. AMM TASK 29-10-00-864-003).
   (3) On the overhead panel 41VU, on the ADIRS MSU:
  • set the three OFF/NAV/ATT selector switches to OFF.
   (4) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
   (5) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).
Subtask 27-96-00-410-067-A
B. Close Access
   (1) Install the protective cover on the battery power center 105VU.
   (2) Tighten the two screws.
   (3) Close the access door 822.
   (4) Remove the access platform(s).
[Rev.10 from 2021] 2026.04.01 04:13:17 UTC
"Aviabrain" 2025