Operational Check of AP Disengagement and Locking Devices of Side Stick Controller and Rudder Pedals

TASK 22-10-00-710-002-A
Operational Check of AP Disengagement and Locking Devices of Side Stick Controller and Rudder Pedals

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

WARNING: MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT. UNWANTED ELECTRICAL POWER CAN BE DANGEROUS.

ZONE: 210

1. Reason for the Job
Refer to the MPD TASK: 221000-01
OPERATIONAL CHECK OF AP DISENGAGEMENT AND LOCKING DEVICES OF SIDE STICK CONTROLLER AND RUDDER PEDALS
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 29-10-00-863-003-A	Pressurize the Blue Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-003-A-01	Pressurize the Blue Hydraulic System with the Blue Electric Pump
TASK 29-10-00-864-003-A	Depressurize the Blue Hydraulic System
TASK 29-23-00-863-001-A	Pressurize the Green Hydraulic System from the Yellow Hydraulic System through the PTU with the Electric Pump
TASK 29-23-00-864-001-A	Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure
TASK 34-10-00-860-004-A	Inertial Reference (IR) Alignment-Procedure
TASK 34-10-00-860-004-A-01	Automatic Inertial Reference (IR) Alignment-Procedure
TASK 34-10-00-860-004-A-02	Inertial Reference (IR) Alignment-Procedure to do a Check of the Links between each Flight Management and Guidance Computer (FMGC) and the three Air Data/Inertial Reference Units (ADIRUs)
TSM 22-11-00-810-835	(for corrective action)

3. Job Set-up
Subtask 22-10-00-860-052-A

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Do the Air Data/Inertial Reference System (ADIRS) alignment procedure (two ADIRSs are necessary for this test)
(Ref. AMM TASK 34-10-00-860-004).
(3) On the overhead panel, on FLT CTL panels 23VU and 24VU:

Make sure that the ELAC 1, ELAC 2, SEC 1, SEC 2, SEC 3, FAC 1 and FAC 2 pushbutton switches are pushed (the FAULT and OFF legends are off).

NOTE: The two Elevator Aileron Computers (ELAC), one Spoiler Elevator Computer (SEC) and one Flight Augmentation Computer (FAC) are necessary for this test.

(4) Do the Electronic Instrument System (EIS) start procedure (Ref. AMM TASK 31-60-00-860-001).
(5) On the center pedestal, on the ECAM control panel, push the F/CTL key (the "F/CTL" page comes into view).
(6) Pressurize the aircraft hydraulic systems
(Ref. AMM TASK 29-23-00-863-001) (Ref. AMM TASK 29-10-00-863-003).

Subtask 22-10-00-865-051-A

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	AUTO FLT/FCU/1	9CA1	B05
49VU	AUTO FLT/FMGC/1	10CA1	B02
** ON A/C NOT FOR ALL
49VU	AUTO FLT/FCU/1	9CA1	H11
49VU	AUTO FLT/FMGC/1	10CA1	H08
** ON A/C NOT FOR ALL
121VU	AUTO FLT/RUDDER/ARTF/FEEL	14CA	N17
121VU	AUTO FLT/STICK/LOCK	13CA	N16
** ON A/C ALL
121VU	AUTO FLT/FCU/2	9CA2	M21
121VU	AUTO FLT/FMGC/2	10CA2	M17
** ON A/C NOT FOR ALL
121VU	AUTO FLT/RUDDER/ARTF/FEEL	14CA	N19
121VU	AUTO FLT/STICK/LOCK	13CA	N18

4. Procedure
Subtask 22-10-00-710-051-C

A. Do this test:

NOTE: You can ignore the warnings related to this test.

NOTE: If the results of the test are not satisfactory, it is necessary to do the troubleshooting procedure TSM 22-11-00-810-835.

ACTION	RESULT
1.On the Flight Control Unit (FCU), on glareshield 13VU: Make sure that the FD pushbutton switches are pushed.	On the top section of the CAPT and F/O PFDs: The white "1FD2" indication comes into view.
2.Open circuit breaker 10CA2.	On the F/O PFD: The "1FD1" indication comes into view.
3.Move one pedal to operate the rudder pedals until its mechanical stop. Do the same for the other pedal.	On the SD, on the "F/CTL" page: The rudder moves in relation to the command. You can feel the usual resistance on the rudder pedals.
4.Make sure that when you move the CAPT(F/O) rudder pedal, the F/O(CAPT) rudder pedal moves in the same direction.
5.Move the rudder pedals to the neutral position.
6.Move the CAPT side-stick controller around its axis and then to zero.	The side stick controller moves freely.
7.Move the F/O side-stick controller around its axis and then to zero.	The side stick controller moves freely.
8.On the FCU: Push the AP1 pushbutton switch to engage AP1. Make sure that the FD pushbutton switch is engaged.	The green light of the pushbutton switch is on. AP1 engages.
9.Apply the usual load on the rudder pedals (do not override the rudder pedal resistance not to disengage the autopilot).	You can feel a resistance on the rudder pedals. NOTE: Rudder pedals give the autopilot engagement threshold.
10.Apply a load on the rudder pedals to override the rudder pedal resistance.	AP1 disengages.
11.Move the rudder pedals to the neutral position.
12.Engage AP1 again.	The green light of the pushbutton switch is on.
13.On the F/O side-stick controller: Move the side stick controller to its mechanical stop. Apply a load on the side stick controller to override the rudder pedal resistance.	The side stick controller is locked. You can feel the usual resistance on the side stick controller. AP1 disengages.
14.Move the F/O side-stick controller to the neutral position.
15.Engage AP1 again.	The green light of the pushbutton switch is on.
16.Do step 13 with the CAPT side-stick controller.	The results are the same as those of step 13.
17.Move the CAPT side-stick controller to the neutral position.
18.Close circuit breaker 10CA2.
19.After the safety test, make sure that FD2 engages.	On the F/O PFD: The "1FD2" indication comes into view.
20.Open circuit breaker 10CA1.	On the CAPT PFD: The "2FD2" indication comes into view.
21.Engage AP2.	The green light of the pushbutton switch is on.
22.Apply the usual load on the rudder pedals (do not override the rudder pedal resistance not to disengage the autopilot).	You can feel a resistance on the rudder pedals. NOTE: Rudder pedals give the autopilot engagement threshold.
23.Apply a load on the rudder pedals to override the rudder pedal resistance.	AP2 disengages.
24.Release the rudder pedals to the neutral position.
25.Engage AP2 again.	The green light of the pushbutton switch is on.
26.On the F/O side-stick controller: Move the side stick controller to its mechanical stop. Apply a load on the side stick controller to override the resistance.	The side stick controller is locked. AP2 disengages.
27.Move the F/O side-stick controller to the neutral position.
28.Engage AP2 again.	The green light of the pushbutton switch is on.
29.Do step 26 with the CAPT side-stick controller.	The results are the same as those of step 26.
30.Move the CAPT side-stick controller to the neutral position.
31.Close circuit breaker 10CA1.
32.After the safety test, make sure that FD1 engages.	On the CAPT PFD: The "1FD2" indication comes into view.
33.Stop the autopilot warnings: Engage AP1 or AP2. Push and release the takeover and priority pushbutton switch on the CAPT or F/O side-stick controller. or Push the MASTER WARN pushbutton switch on the glareshield. Push the CLEAR key on the ECAM Control Panel (ECP).

5. Close-up
Subtask 22-10-00-860-053-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Depressurize the aircraft hydraulic systems
(Ref. AMM TASK 29-23-00-864-001) (Ref. AMM TASK 29-10-00-864-003).
(2) On the overhead panel, on the ADIRS Control and Display Unit (CDU), set the OFF/NAV/ATT selector switches to OFF.
(3) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(4) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

Subtask 22-10-00-860-053-B ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Depressurize the aircraft hydraulic systems
(Ref. AMM TASK 29-23-00-864-001) and (Ref. AMM TASK 29-10-00-864-003).
(2) On the overhead panel, on the ADIRS Mode Selector Unit (IRS) (MSU), set the OFF/NAV/ATT selector switches to OFF.
(3) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(4) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.03.31 23:09:50 UTC