W DOC AIRBUS | AMM A320F

Leak Check of Engine Bleed Air Supply System and Packs Components with APU Bleed Air

TASK 36-11-00-720-005-A
Leak Check of Engine Bleed Air Supply System and Packs Components with APU Bleed Air

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.
WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
ZONE: 210
1. Reason for the Job
To make sure that there are no leaks from the air bleed system downstream of the high-pressure bleed valve and intermediate-pressure bleed check-valve. Pressurization by APU and the bleed pressure regulator valve (PRV) test port.
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific
AR
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
AR
AIR SOURCE 3 BAR (43.5 PSI) - REGULATED, FILTERED, DRY
No specific
AR
PLUG - BLANKING
No specific
AR
WARNING NOTICE(S)
98D27803000000
AR
LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
210
CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD
151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW, 161CW, 191BB, 191BT, 191CT, 192BT, 192CT, 192FB, 197BB, 312AR, 521AB, 521BT, 521CB, 521EB, 621AB, 621BT, 621CB, 621EB, 825
197KB, 197SB
FOR [1000EM1] (ENGINE-1)
437AL, 451AL
413CL, 413DL, 414CR, 414FR
413DT, 471AL, 471AR
FOR [1000EM2] (ENGINE-2)
447AL, 461AL
413CL
423DT, 481AL, 481AR
423CL, 423DL, 423FL, 424CR
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 12-33-21-618-001-A-02
Pre-conditioning with the APU
TASK 24-41-00-861-002-A
Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01
Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02
Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A
De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01
De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02
De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 25-55-11-000-003-A
Removal of the Sidewall Panels in the Aft Cargo Compartment - FR47/FR59
TASK 25-55-11-400-003-A
Installation of the Sidewall Panels in the Aft Cargo Compartment - FR47/FR59
TASK 25-55-12-000-003-A
Removal of the Sidewall Panels in the Aft Cargo Compartment - FR59/FR65
TASK 25-55-12-400-003-A
Installation of the Sidewall Panels in the Aft Cargo Compartment - FR59/FR65
TASK 27-00-00-080-002-A
Removal of the Flap/Slat Control-Lever Locking Tool (98D27803000000)
TASK 31-60-00-860-001-A
EIS Start Procedure
TASK 31-60-00-860-002-A
EIS Stop Procedure
TASK 36-22-00-790-001-A
Leak Check on all the Bleed Air Ducts and the Packs Components
TASK 49-00-00-860-005-A
APU Start by External Power
TASK 49-00-00-860-005-A-01
APU Start by Batteries
TASK 49-00-00-860-006-A
APU Shutdown by External Power
TASK 49-00-00-860-006-A-01
APU Shutdown by Batteries
TASK 49-00-00-860-008-A
APU Start by External Power
TASK 49-00-00-860-008-A-01
APU Start by Batteries
TASK 49-00-00-860-009-A
APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01
APU Shutdown by Batteries (131-9(A))
TASK 52-30-00-860-001-A
Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
TASK 52-30-00-860-002-A
Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
TASK 53-35-11-000-001-A
Removal of the Wing-to-Fuselage Fairings
TASK 53-35-11-400-001-A
Installation of the Wing-to-Fuselage Fairings
TASK 53-35-13-000-002-A
Removal of the Quick-Release Access Panels from the Belly Fairing Structure
TASK 53-35-13-400-002-A
Installation of the Quick-Release Access Panels on the Belly Fairing Structure
TASK 57-41-37-000-004-A
Removal of the Pressure Relief Panels
TASK 57-41-37-000-009-A
Removal of the Access Panel
TASK 57-41-37-400-002-A
Installation of the Pressure Relief Panels
TASK 57-41-37-400-009-A
Installation of the Access Panel
F Pressure Regulator Valve - Location ** ON A/C NOT FOR ALL
F Pressure Regulator Valve - Detail
F Pressure Regulator Valve - Location ** ON A/C NOT FOR ALL
F Pressure-Regulator Valve Control-Solenoid
F Engine Bleed Air Supply System ** ON A/C NOT FOR ALL
F Engine Bleed Air Supply System ** ON A/C NOT FOR ALL
FOR [1000EM1] (ENGINE-1)
TASK 54-52-11-000-002-A
Removal of the Access Panels
TASK 54-52-11-000-002-B
Removal of the Access Panels
TASK 54-52-11-400-002-A
Installation of the Access Panels
TASK 54-52-11-400-002-B
Installation of the Access Panels
TASK 54-53-11-000-002-B
Removal of the Pylon-to-Wing Access Panels
TASK 54-53-11-400-002-B
Installation of the Pylon-to-Wing Access Panels
TASK 71-13-00-010-010-A
Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-010-040-A
Opening of the Fan Cowl Doors
TASK 71-13-00-010-040-B
Opening of the Fan Cowl Doors
TASK 71-13-00-410-010-A
Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-040-A
Closing of the Fan Cowl Doors
TASK 71-13-00-410-040-B
Closing of the Fan Cowl Doors
TASK 78-32-00-010-010-A
Opening of the Thrust Reverser Halves
TASK 78-32-00-410-010-A
Closing of the Thrust Reverser Halves
TASK 78-36-00-010-040-A
Opening of the Thrust Reverser Doors
TASK 78-36-00-010-040-B
Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-A
Closing of the Thrust Reverser Doors
TASK 78-36-00-410-040-B
Closing of the Thrust Reverser Doors
FOR [1000EM2] (ENGINE-2)
TASK 54-52-11-000-002-A
Removal of the Access Panels
TASK 54-52-11-000-002-B
Removal of the Access Panels
TASK 54-52-11-400-002-A
Installation of the Access Panels
TASK 54-52-11-400-002-B
Installation of the Access Panels
TASK 54-53-11-000-002-B
Removal of the Pylon-to-Wing Access Panels
TASK 54-53-11-400-002-B
Installation of the Pylon-to-Wing Access Panels
TASK 71-13-00-010-010-A
Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-010-040-A
Opening of the Fan Cowl Doors
TASK 71-13-00-010-040-B
Opening of the Fan Cowl Doors
TASK 71-13-00-410-010-A
Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-040-A
Closing of the Fan Cowl Doors
TASK 71-13-00-410-040-B
Closing of the Fan Cowl Doors
TASK 78-32-00-010-010-A
Opening of the Thrust Reverser Halves
TASK 78-32-00-410-010-A
Closing of the Thrust Reverser Halves
TASK 78-36-00-010-040-A
Opening of the Thrust Reverser Doors
TASK 78-36-00-010-040-B
Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-A
Closing of the Thrust Reverser Doors
TASK 78-36-00-410-040-B
Closing of the Thrust Reverser Doors
3. Job Set-up
Subtask 36-11-00-861-076-A ** ON A/C NOT FOR ALL
A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002)
Subtask 36-11-00-941-076-A ** ON A/C NOT FOR ALL
B. Safety Precautions
   (1) Make sure that engine 1(2) shut down occurred not less than 5 minutes before you do this procedure.
   (2) On panel 115VU, put a WARNING NOTICE(S) to tell persons not to start the engine 1(2).
   (3) In the cockpit, on center pedestal panel 114VU:
  • Install a 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION in position on the flap and slat control lever.
  • Put the WARNING NOTICE(S) on the flap and slat control lever to tell persons not to operate the flap and slat controls.
   (4) In the cockpit, put the WARNING NOTICE(S) to tell persons not to operate the pneumatic system.
   (5) On the ENG section of maintenance panel 50VU:
  • Make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off
  • Put the WARNING NOTICE(S) to tell persons not to operate the FADEC 1(2).
Subtask 36-11-00-865-056-A ** ON A/C NOT FOR ALL
C. Make sure that this(these) circuit breaker(s) is(are) closed:
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUAIR BLEED/X FEED/VALVE/BAT2HVD13
49VUAIR BLEED/ENG 1/CTL3HA1D12
49VUAIR BLEED/ENG 1/MONG2HA1D11
122VUAIR BLEED/ENG 2/CTL3HA2Z23
122VUAIR BLEED/ENG 2/MONG2HA2Z22
122VUAIR BLEED/X FEED VALVE/NORM1HVZ20
Subtask 36-11-00-010-059-A ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below zones 191 and 192.
   (2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below zones 521 and 621.
   (3) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below AFT cargo-compartment door 825.
   (4) Remove access panels 191BB and 192FB of the air conditioning units (Ref. AMM TASK 53-35-13-000-002).
   (5) Remove the access panels on the wings and belly fairings:
     (a) For the left wing and belly fairing:
     (b) For the right wing and belly fairing:
   (6) Remove these access panels on the pylon:
     (a) FOR [1000EM1] (ENGINE-1)
413CL, 414CR , 413DL and 414FR (Ref. AMM TASK 54-52-11-000-002)
     (b) FOR [1000EM2] (ENGINE-2)
423CL, 424CR, 423DL and 423FL (Ref. AMM TASK 54-52-11-000-002).
   (7) Open the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-010-040)
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-010-040).
   (8) Open the left thrust-reverser-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-36-00-010-040)
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-36-00-010-040).
   (9) Open AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001) and access door 312AR.
   (10) In the AFT cargo compartment, remove sidewall panels 151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW and 161CW (Ref. AMM TASK 25-55-11-000-003) and (Ref. AMM TASK 25-55-12-000-003).
Subtask 36-11-00-010-059-C ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below zones 191 and 192.
   (2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below zones 521 and 621.
   (3) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below AFT cargo-compartment door 825.
   (4) Remove access panels 191BB and 192FB of the air conditioning units (Ref. AMM TASK 53-35-13-000-002).
   (5) Remove the access panels on the wings and belly fairings:
     (a) For the left wing and belly fairing:
     (b) For the right wing and belly fairing:
   (6) Remove these access panels on the pylon:
     (a) FOR [1000EM1] (ENGINE-1)
413CL, 414CR, 413DL and 414FR (Ref. AMM TASK 54-52-11-000-002)
     (b) FOR [1000EM2] (ENGINE-2)
423CL, 424CR, 423DL and 423FL (Ref. AMM TASK 54-52-11-000-002).
   (7) Open the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-010-040)
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-010-040).
   (8) Open the left thrust-reverser-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-36-00-010-040)
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-36-00-010-040).
   (9) Open AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001) and access door 312AR.
   (10) In the AFT cargo compartment, remove sidewall panels 151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW and 161CW (Ref. AMM TASK 25-55-11-000-003) and (Ref. AMM TASK 25-55-12-000-003).
Subtask 36-11-00-010-059-F ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below zones 191 and 192.
   (2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below zones 521 and 621.
   (3) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below AFT cargo-compartment door 825.
   (4) Remove access panels 191BB and 192FB of the air conditioning packs (Ref. AMM TASK 53-35-13-000-002).
   (5) Remove the access panels on the wings and belly fairings:
     (a) For the left wing and belly fairing:
     (b) For the right wing and belly fairing:
   (6) Remove the access panels on the pylon:
     (a) FOR [1000EM1] (ENGINE-1)
413DT and 471AR (Ref. AMM TASK 54-53-11-000-002)
     (b) FOR [1000EM2] (ENGINE-2)
423DT and 481AL (Ref. AMM TASK 54-53-11-000-002)
   (7) Open the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-010-010)
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-010-010).
   (8) Open the left thrust-reverser-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-32-00-010-010)
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-32-00-010-010).
   (9) Open AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001) and access door 312AR.
   (10) In the AFT cargo compartment, remove sidewall panels 151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW and 161CW (Ref. AMM TASK 25-55-11-000-003) and (Ref. AMM TASK 25-55-12-000-003).
Subtask 36-11-00-010-059-G ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below zones 191 and 192.
   (2) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below zones 521 and 621.
   (3) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position below AFT cargo-compartment door 825.
   (4) Remove the applicable access panels 191BB and 192FB of the air conditioning units (Ref. AMM TASK 53-35-13-000-002).
   (5) Remove the applicable access panels on the wings and the belly fairings as follows:
     (a) For the left wing and the belly fairing:
     (b) For the right wing and the belly fairing:
   (6) Remove the access panels on the pylon as follows:
     (a) FOR [1000EM1] (ENGINE-1)
413DT (Ref. AMM TASK 54-52-11-000-002).
     (b) FOR [1000EM2] (ENGINE-2)
423DT (Ref. AMM TASK 54-52-11-000-002).
   (7) Open the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-010-040).
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-010-040).
   (8) Open the left thrust-reverser door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-36-00-010-040).
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-36-00-010-040).
   (9) Open AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
   (10) Open access door 312AR.
   (11) In the AFT cargo compartment, remove the applicable sidewall panels as follows:
Subtask 36-11-00-860-058-A ** ON A/C NOT FOR ALL
E. Aircraft Maintenance Configuration
   (1) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
   (2) Do the pre-conditioning with the APU (Ref. AMM TASK 12-33-21-618-001).
   (3) In the air conditioning compartment:
  • Disconnect the pressurization interconnection line of the water tank, hydraulic reservoir and trim air valve from the pressure-service check valves (7272HM and 7270HM).
   (4) Cap the disconnected ends with PLUG - BLANKING.
   (5) On the Pressure Regulator Valve (PRV) (4001HA):
F Pressure Regulator Valve - Location ** ON A/C NOT FOR ALL
F Pressure Regulator Valve - Detail ** ON A/C NOT FOR ALL
F Pressure Regulator Valve - Location ** ON A/C NOT FOR ALL
  • Remove the cap from the test port
  • Connect an AIR SOURCE 3 BAR (43.5 PSI) - REGULATED, FILTERED, DRY to the test port
  • Increase the pressure to 40 psi (2.7579 bar) and stabilize it at this value.
  • Make sure that the valve is open: look at the manual position indicator.
NOTE: This procedure is to open the bleed PRV.
   (6) On control solenoid 10HA1 (10HA2) of the PRV, disconnect the electrical connector (1).
F Pressure-Regulator Valve Control-Solenoid ** ON A/C NOT FOR ALL
   (7) On ECAM control panel 11VU:
  • Push the BLEED pushbutton switch (the BLEED page comes into view on the lower ECAM display unit).
   (8) On AIR COND panel 30VU, make sure that:
  • The PACK1 and PACK2 pushbutton switches are pushed (the OFF legends are off)
  • The X BLEED selector switch is set to AUTO position (the BLEED page shows that the CROSSBLEED valve is closed)
  • The APU BLEED pushbutton switch is released (the ON legend is off) (the BLEED page shows that the APU BLEED valve is closed).
   (9) On the ANTI ICE section of panel 25VU:
  • Make sure that the ANTI ICE/WING pushbutton switch is released (the ON legend is off).
4. Procedure
Subtask 36-11-00-720-053-A ** ON A/C NOT FOR ALL
A. Functional Test of the Engine Bleed-Air-Supply System
   (1) Start APU:
     (a) After the APU starts, wait for a minimum of 3 minutes for the warm up period, before you select the APU BLEED.
   (2) In the cockpit, on AIR COND panel 30VU, push the APU BLEED pushbutton switch (the ON legend is on) to pressurize the bleed duct system.
The BLEED page shows that:
  • The CROSSBLEED valve is open
  • The APU bleed valve is open.
   (3) On the ECAM control panel:
  • Push the APU BLEED pushbutton switch (the APU page comes into the view on the lower ECAM display-unit and shows the APU BLEED pressure).
   (4) Do a leak test of the ducts of the bleed system (Ref. AMM TASK 36-22-00-790-001).
5. Close-up
Subtask 36-11-00-860-059-A ** ON A/C NOT FOR ALL
A. Put the aircraft back to its initial configuration.
   (1) On the AIR COND panel 30VU, release the APU BLEED pushbutton switch (the ON legend is off)
   (2) Stop the APU:
   (3) Stop the pre-conditioning with the APU (Ref. AMM TASK 12-33-21-618-001).
   (4) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002)
   (5)
F Pressure-Regulator Valve Control-Solenoid ** ON A/C NOT FOR ALL
   (6) On the PRV (4001HA):
F Pressure Regulator Valve - Location ** ON A/C NOT FOR ALL
F Pressure Regulator Valve - Detail ** ON A/C NOT FOR ALL
F Pressure Regulator Valve - Location ** ON A/C NOT FOR ALL
  • Stop the pressurization of the valve with the air supply
  • Make sure that the valve closes: look at the manual position indicator
  • Disconnect the air supply source
  • Install the cap on the test port.
   (7) In the air conditioning compartment:
  • Remove the PLUG - BLANKING
  • Connect the pressurization interconnection lines of the water tank, hydraulic reservoir and trim air valve to the pressure service check-valves (7272HM and 7270HM).
   (8) Make sure that the work area is clean and clear of tools and other items.
   (9) Install the access panels 191BB and 192FB of the air conditioning units (Ref. AMM TASK 53-35-13-400-002).
Subtask 36-11-00-410-060-A ** ON A/C NOT FOR ALL
B. Close Access
   (1) In the AFT cargo compartment, install sidewall panels 151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW and 161CW (Ref. AMM TASK 25-55-11-400-003) and (Ref. AMM TASK 25-55-12-400-003).
   (2) Close AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002) and access door 312AR.
   (3) Close the left thrust-reverser-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-36-00-410-040)
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-36-00-410-040).
   (4) Close the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-410-040)
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-410-040).
   (5) Install the access panels under the leading edge of the wing and belly fairings:
     (a) For the left wing and belly fairing:
     (b) For the right wing and belly fairing:
   (6) Install these access panels on the pylon:
     (a) FOR [1000EM1] (ENGINE-1)
413CL, 414CR, 413DL and 414FR (Ref. AMM TASK 54-52-11-400-002)
     (b) FOR [1000EM2] (ENGINE-2)
413CL, 424CR, 423DL and 423FL (Ref. AMM TASK 54-52-11-400-002).
   (7) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap and slat control lever.
   (8) Remove the WARNING NOTICE(S).
   (9) Remove the access platform(s).
Subtask 36-11-00-410-060-C ** ON A/C NOT FOR ALL
B. Close Access
   (1) In the AFT cargo compartment, install sidewall panels 151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW and 161CW (Ref. AMM TASK 25-55-11-400-003) and (Ref. AMM TASK 25-55-12-400-003).
   (2) Close AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002) and access door 312AR.
   (3) Close the left thrust-reverser-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-36-00-410-040)
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-36-00-410-040).
   (4) Close the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-410-040)
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-410-040).
   (5) Install the access panels under the leading edge of the wing and belly fairings:
     (a) For the left wing and belly fairing:
     (b) For the right wing and belly fairing:
   (6) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap and slat control lever.
   (7) Remove the WARNING NOTICE(S).
   (8) Remove the access platform(s).
Subtask 36-11-00-410-060-F ** ON A/C NOT FOR ALL
B. Close Access
   (1) In the AFT cargo compartment, install sidewall panels 151CW, 151DW, 151EW, 151HW, 151JW, 161AW, 161BW and 161CW (Ref. AMM TASK 25-55-11-400-003) and (Ref. AMM TASK 25-55-12-400-003).
   (2) Close AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002) and access door 312AR.
   (3) Close the left thrust-reverser-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-32-00-410-010)
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-32-00-410-010)
   (4) Close the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-410-010)
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-410-010).
   (5) Install the access panels under the leading edge of the wing and belly fairings:
     (a) For the left wing and belly fairing:
     (b) For the right wing and belly fairing:
   (6) Install these access panels on the pylon:
     (a) FOR [1000EM1] (ENGINE-1)
     (b) FOR [1000EM2] (ENGINE-2)
   (7) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap and slat control lever.
   (8) Remove the WARNING NOTICE(S).
   (9) Remove the access platform(s).
Subtask 36-11-00-410-060-G ** ON A/C NOT FOR ALL
B. Close Access
   (1) In the AFT cargo compartment, install the applicable sidewall panels as follows:
   (2) Close AFT cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002).
   (3) Close access door 312AR.
   (4) Close the left thrust-reverser door:
     (a) FOR [1000EM1] (ENGINE-1)
451AL (Ref. AMM TASK 78-36-00-410-040).
     (b) FOR [1000EM2] (ENGINE-2)
461AL (Ref. AMM TASK 78-36-00-410-040).
   (5) Close the left fan-cowl door:
     (a) FOR [1000EM1] (ENGINE-1)
437AL (Ref. AMM TASK 71-13-00-410-040).
     (b) FOR [1000EM2] (ENGINE-2)
447AL (Ref. AMM TASK 71-13-00-410-040).
   (6) Install the access panels on the pylon as follows:
     (a) FOR [1000EM1] (ENGINE-1)
413DT (Ref. AMM TASK 54-52-11-400-002).
     (b) FOR [1000EM2] (ENGINE-2)
423DT (Ref. AMM TASK 54-52-11-400-002).
   (7) Install the access panels on the wings and the belly fairings as follows:
     (a) For the left wing and the belly fairing:
     (b) For the right wing and the belly fairing:
   (8) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap and slat control lever (Ref. AMM TASK 27-00-00-080-002).
   (9) Remove the access platform(s).
   (10) Remove the WARNING NOTICE(S).
Subtask 36-11-00-862-072-A ** ON A/C NOT FOR ALL
C. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
[Rev.10 from 2021] 2026.04.01 12:37:35 UTC
"Aviabrain" 2025