Installation of the Lower Sense Line between the Bleed-Air Precooler Exchanger (Downstream) and the Fan Air-Valve Actuator

TASK 36-11-49-400-837-A
Installation of the Lower Sense Line between the Bleed-Air Precooler Exchanger (Downstream) and the Fan Air-Valve Actuator

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

WARNING: YOU MUST NOT TOUCH HOT PARTS WITHOUT APPLICABLE GLOVES. HOT PARTS CAN CAUSE AN INJURY.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: BE VERY CAREFUL WHEN YOU DO WORK ON OR NEAR THE AIR-CONDITIONING DUCTS. THE DUCTS ARE MADE OF THIN MATERIAL AND YOU CAN EASILY BREAK THEM.

ZONE: 410
ZONE: 420
ZONE: 472
ZONE: 482

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	PLUG - BLANKING
No specific	AR	WARNING NOTICE(S)
No specific	1	WRENCH - STANDARD
98D27803000000	1	LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
98L12003001000	1	HARNESS,SAFETY

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.06ABB2)	Polysulfide Sealant-Fuel Tank Fillet 120 degre Celsius

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
410	ENG 1 PYLON BOX AND FORWARD FAIRING
420	ENG 2 PYLON BOX AND FORWARD FAIRING
472	PYLON LEADING EDGE
482	PYLON LEADING EDGE
191DB
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
413ET, 415AL, 415AR, 437AL, 438AR, 451AL, 452AR, 472AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
423ET, 424CR, 425AL, 425AR, 447AL, 448AR, 461AL, 462AR

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
11	SEAL	AIPC 36-11-86-50-300

E. Referenced Information

REFERENCE	DESIGNATION
TASK 12-00-00-481-002-A	Installation of the Wingrip
TASK 20-23-22-910-001-A	Marking of the Unions after Application of Standard or Specific Tightening Torque
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 27-00-00-480-002-A	Installation of the Flap/Slat Control-Lever Locking Tool (98D27803000000)
TASK 36-12-00-860-805-A	Pressurization of the Bleed System with the APU
TASK 36-12-00-860-806-A	Pressurization of the Bleed System through the HP Ground Connector
TASK 36-22-00-790-803-A	Leak Check on all the Bleed Air Ducts and the Pack Components
TASK 49-00-00-860-009-A	APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01	APU Shutdown by Batteries (131-9(A))
TASK 54-51-21-000-804-A	Removal of the Pylon Lateral Access-Doors
TASK 54-51-21-400-803-A	Installation of the Pylon Lateral Access-Doors
TASK 54-53-11-000-806-A	Removal of the Pylon-to-Wing Access Panels and Doors
TASK 54-53-11-400-806-A	Installation of the Pylon-to-Wing Access Panels and Doors
TASK 71-13-00-010-803-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-803-A	Closing of the Fan Cowl Doors
TASK 78-30-00-040-809-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-809-A	Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-010-806-A	Opening of the Thrust Reverser Cowl Doors
TASK 78-36-00-410-806-A	Closing of the Thrust Reverser Cowl Doors
Lower Sense Line between the Interface Pylon and the Fan Air-Valve Actuator
Electrical Harnesses

3. Job Set-up
Subtask 36-11-49-861-134-A

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002) or (Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-49-941-153-A

B. Safety Precautions
(1) Make sure that the engine 1(2) shutdown occurred not less than five minutes before you do this procedure.
(2) On AIR COND panel 30VU:
(a) Make sure that the ENG 1(2) BLEED pushbutton switch is released (OFF legend on).
(b) Make sure that the APU BLEED pushbutton switch is released (ON legend off).
(c) Make sure that the WARNING NOTICE(S) is in position to tell persons not to operate the pneumatic system.
(3) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Make sure that the WARNING NOTICE(S) are in position to tell persons not to operate:

The ENG/MODE selector switch, and
The ENG/MASTER 1(2) control switch.

(4) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Make sure that the WARNING NOTICE(S) is in position to tell persons not to energize FADEC 1(2).
(5) On access door 191DB, on the HP ground connector:
(a) Make sure that the WARNING NOTICE(S) is in position to tell persons not to pressurize the pneumatic system.
(6) On FLAPS panel 114VU:

Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is in position on the flap/slat control lever (Ref. AMM TASK 27-00-00-480-002).
Make sure that the WARNING NOTICE(S) is in position on the flap/slat control lever to tell persons not to operate the flap/slat controls.

(7) Put on and attach a 98L12003001000 HARNESS,SAFETY before you start work in the work area (Ref. AMM TASK 12-00-00-481-002).

Subtask 36-11-49-865-238-A

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
FOR FIN: 4020KM1 (POWER PLANTDEMOUNTABLE, ENGINE 1)
49VU	AIR BLEED/ENG 1/CTL	2HA1	D11
122VU	AIR BLEED/ENG 1/MONG	3HA1	Z23
FOR FIN: 4020KM2 (POWER PLANTDEMOUNTABLE, ENGINE 2)
49VU	AIR BLEED/ENG 2/MONG	3HA2	D12
122VU	AIR BLEED/ENG 2/CTL	2HA2	Z22

Subtask 36-11-49-010-295-A

D. Get Access
(1) Make sure that these fan cowl doors are open (Ref. AMM TASK 71-13-00-010-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR
(2) Make sure that an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position.

Subtask 36-11-49-040-179-A

E. Deactivation of the Thrust Reverser for Ground Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Make sure that the thrust reverser system is deactivated for ground maintenance (Ref. AMM TASK 78-30-00-040-809).

Subtask 36-11-49-010-296-A

F. Get Access
(1) Make sure that the thrust reverser cowl-doors are open (Ref. AMM TASK 78-36-00-010-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR
(2) Make sure that these access panels are removed (Ref. AMM TASK 54-51-21-000-804):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
415AL 415AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
425AL 425AR

4. Procedure
Subtask 36-11-49-420-161-A

A. Installation of the Lower Sense Line between the Pylon Interface and the Fan Air-Valve Actuator
(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM D/O 49-00-00-86)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

(3) Remove the PLUG-BLANKING from each disconnected line end.
(4) Remove the PLUG - BLANKING from the port of the fan air-valve actuator (20).
(5) Do an inspection of the component interfaces and the adjacent area.
(6) Clean the component interfaces and the adjacent area.
(7) Put the lower sense line (17) in the correct position between the fan air-valve actuator (20) and the pylon interface (18).
(8) Connect the lower sense line (17) with the union nut (19) to the fan air-valve actuator (20). Do not tighten the union nut (19) at this time.
(9) Install the clamp (23) as follows:
(a) Install the clamp (23) with the lower sense line (17) on the support (24).
(b) Install the washers (22) and the bolts (21) in the clamp (23).
(c) Tighten the bolts (21).
(10) Use a second WRENCH - STANDARD to hold the fan air-valve actuator (20) and tighten the union nut (19) of the lower sense line (17).
(11) Identify the tightened union nut (19) of the lower sense line (17) with a red line (Ref. AMM TASK 20-23-22-910-001).

Subtask 36-11-49-480-096-A

B. Prepare for the Leak Test on the Connection of the Sense Line (17) with the Fan Air-Valve Actuator (20)
(1) Use the the aluminum foil procedure (Ref. AMM TASK 36-22-00-790-803).

Subtask 36-11-49-410-222-A

C. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Close the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-410-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR

Subtask 36-11-49-440-129-A

D. Do the reactivation of the thrust reverser system after ground maintenance (Ref. AMM TASK 78-30-00-440-809).

Subtask 36-11-49-410-223-A

E. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR

Subtask 36-11-49-010-297-A

F. Get Access
(1) Put an ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position at the pylon access panels.
(2) Make sure that these access panels are removed (Ref. AMM TASK 54-53-11-000-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
413ET 472AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
423ET 424CR

Subtask 36-11-49-420-162-A

G. Connection of the Lower Sense Line to the Upper Sense Line
(1) Make sure that the bellows (9) is removed.
(2) Make sure that the electrical harnesses (5) are disengaged, if necessary

Electrical Harnesses

(3) Remove the PLUG - BLANKING from the port of the upper sense line (15).
(4) Do an inspection of the component interfaces and the adjacent area.
(5) Clean the component interfaces and the adjacent area.
(6) Install the two washers (13) and the two bolts (14) in the lower sense line (17).
(a) Tighten the two bolts (14).
(7) Apply a layer of Polysulfide Sealant-Fuel Tank Fillet 120 degre Celsius (Material No.06ABB2) around the hole of the pylon interface (18) and on the heads of the two bolts (14).
(8) Install the upper sense line (15) on the lower sense line (17).
(a) Tighten the union nut (16) of the upper sense line (15).
(b) Identify the tightened union nut (16) of the upper sense line (15) with a red line (Ref. AMM TASK 20-23-22-910-001).

Subtask 36-11-49-865-239-A

H. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
FOR FIN: 4020KM1 (POWER PLANTDEMOUNTABLE, ENGINE 1)
49VU	AIR BLEED/ENG 1/CTL	2HA1	D11
122VU	AIR BLEED/ENG 1/MONG	3HA1	Z23
FOR FIN: 4020KM2 (POWER PLANTDEMOUNTABLE, ENGINE 2)
49VU	AIR BLEED/ENG 2/MONG	3HA2	D12
122VU	AIR BLEED/ENG 2/CTL	2HA2	Z22

Subtask 36-11-49-480-097-A

I. Prepare for the Leak Test on the Connection of the Lower Sense Line (17) with the Upper Sense Line (15).
(1) Use the aluminum foil procedure (Ref. AMM TASK 36-22-00-790-803).

Subtask 36-11-49-790-066-A

J. Leak Test
(1) Pressurize the bleed system through the HP ground connector (Ref. AMM TASK 36-12-00-860-806) or with the APU (Ref. AMM TASK 36-12-00-860-805).
(a) Make sure that there are no leaks at the lower sense line (17) connection (Ref. AMM TASK 36-22-00-790-803).
(2) Remove the materials that you used to do the leak test on the lower sense line (17) connection.

Subtask 36-11-49-420-163-A

K. Installation of the Components
(1) If disengaged, install the six clamps (3) and the three electrical harnesses (5) on the support (4).

Electrical Harnesses

(a) Put the six clamps (3) and the three electrical harnesses (5) on the support (4).
(b) Install the six washers (2) and the six bolts (1).
(c) Tighten the six bolts (1).
(2) Install the bellows (9):

Lower Sense Line between the Interface Pylon and the Fan Air-Valve Actuator

(a) Install a new AIPC 36-11-86-50-300 SEAL (11)
(b) Put the bellows (9) in position between the precooler exchanger (12) and the wing bleed duct (6).
(c) Install the clamps (7) and (10) on the bellows (9).
(d) Make sure that the position of the clamps (7) and (10) agree with the position you recorded at the removal.
(e) Tighten the nut of the clamp (7).
(f) Tighten the nut of the clamp (10).
(g) Identify the tightened union nuts of the clamps (7) and (10) with a red line (Ref. AMM TASK 20-23-22-910-001).

Subtask 36-11-49-410-224-A

L. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install these access panels (Ref. AMM TASK 54-53-11-400-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
413ET 472AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
423ET 424CR
(3) Remove the access platform(s).

Subtask 36-11-49-010-298-A

M. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR

Subtask 36-11-49-040-180-A

N. Deactivation of the Thrust Reverser System for Ground Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for ground maintenance (Ref. AMM TASK 78-30-00-040-809).

Subtask 36-11-49-010-299-A

O. Get Access
(1) Open the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-010-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.

Subtask 36-11-49-080-067-A

P. Leak Test
(1) Make sure that there are no leaks at the lower sense line (12) connection (Ref. AMM TASK 36-22-00-790-803).
(a) Remove the materials that you used to do the leak test on the lower sense line (12) connection.

5. Close-up
Subtask 36-11-49-410-225-A

A. Close Access
(1) Put the aircraft back to its initial configuration.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) Install these access panels (Ref. AMM TASK 54-51-21-400-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
415AL 415AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
425AL 425AR
(4) Close the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-410-806).
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR

Subtask 36-11-49-440-130-A

B. Do the reactivation of the thrust reverser system after ground maintenance (Ref. AMM TASK 78-30-00-440-809).

Subtask 36-11-49-410-226-A

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

Subtask 36-11-49-862-123-A

D. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002) or (Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 01:12:02 UTC