Removal of the Filter of the Fan-Air Valve Control-Thermostat

TASK 36-11-43-000-003-A
Removal of the Filter of the Fan-Air Valve Control-Thermostat

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 4M (13 FT)
No specific	AR	PLUG - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	1	SOCKET DIA 1/2 IN (12.7 MM)
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [7170HM1] (THERMOSTAT-FAN AIR VALVE CTL)
413DT
413CL, 413DL, 414CR
FOR [7170HM2] (THERMOSTAT-FAN AIR VALVE CTL)
423CL, 423DL, 424CR
423DT

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 36-11-43-000-003-A	Removal of the Filter of the Fan-Air Valve Control-Thermostat
TASK 36-11-43-100-001-A	Remove the Thermostat-Filter of the Fan Air Valve-Control for Cleaning
TASK 36-11-43-400-003-A	Installation of the Filter of the Fan-Air-Valve Control Thermostat
TASK 49-00-00-860-006-A	APU Shutdown by External Power
TASK 49-00-00-860-006-A-01	APU Shutdown by Batteries
TASK 49-00-00-860-009-A	APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01	APU Shutdown by Batteries (131-9(A))
Thermostat Filter ** ON A/C NOT FOR ALL
Thermostat Filter ** ON A/C NOT FOR ALL
Thermostat Filter ** ON A/C NOT FOR ALL
FOR [7170HM1] (THERMOSTAT-FAN AIR VALVE CTL)
TASK 54-52-11-000-002-A	Removal of the Access Panels
TASK 54-52-11-000-002-B	Removal of the Access Panels
FOR [7170HM2] (THERMOSTAT-FAN AIR VALVE CTL)
TASK 54-52-11-000-002-A	Removal of the Access Panels
TASK 54-52-11-000-002-B	Removal of the Access Panels

3. Job Set-up
Subtask 36-11-43-861-051-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002) or (Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-43-941-054-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

NOTE: To prevent damage to the thermostat, we recommend that you wait until it is at the ambient temperature before you start the work.

(2) On the AIR COND panel 30VU:

make sure that the ENG 1(2) BLEED pushbutton switch is released (the OFF legend is on),
make sure that the APU BLEED pushbutton switch is released (the ON legend is off),
put a WARNING NOTICE(S) to tell persons not to operate the pneumatic system.

(3) On the ENG panel 115VU:

put a WARNING NOTICE(S) to tell persons not to start the engine 1(2).

(4) On the HP ground connector:

Put a WARNING NOTICE(S) to tell persons not to pressurize the pneumatic system.

(5) On the ENG section of the panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 36-11-43-865-058-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	AIR BLEED/ENG 1/CTL	3HA1	D12
49VU	AIR BLEED/ENG 1/MONG	2HA1	D11
122VU	AIR BLEED/ENG 2/CTL	3HA2	Z23
122VU	AIR BLEED/ENG 2/MONG	2HA2	Z22

Subtask 36-11-43-010-054-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Put the ACCESS PLATFORM 4M (13 FT) in position below the engine.
(2) Remove the access panels:
(a) FOR [7170HM1] (THERMOSTAT-FAN AIR VALVE CTL)
413CL, 414CR and 413DL (Ref. AMM TASK 54-52-11-000-002).
(b) FOR [7170HM2] (THERMOSTAT-FAN AIR VALVE CTL)
423CL, 424CR and 423DL (Ref. AMM TASK 54-52-11-000-002).

Subtask 36-11-43-010-054-B ** ON A/C NOT FOR ALL

D. Get Access
(1) Put the ACCESS PLATFORM 4M (13 FT) in position below the engine.
(2) Remove the access panels:
(a) FOR [7170HM1] (THERMOSTAT-FAN AIR VALVE CTL)
413DT (Ref. AMM TASK 54-52-11-000-002).
(b) FOR [7170HM2] (THERMOSTAT-FAN AIR VALVE CTL)
423DT (Ref. AMM TASK 54-52-11-000-002).

4. Procedure
Subtask 36-11-43-020-054-B ** ON A/C NOT FOR ALL

A. Removal of the Filter of the Fan-Air Valve Control-Thermostat

Thermostat Filter ** ON A/C NOT FOR ALL

(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM TASK 49-00-00-860-006)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

WARNING: USE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(3) Remove and discard the lockwire from the filter (4).
(4) Use a SOCKET DIA 1/2 IN (12.7 MM) to loosen and remove the filter (4).
(5) If the filter is dirty, clean the filter (Ref. AMM TASK 36-11-43-100-001), or replace it with a new or a clean filter (Ref. AMM TASK 36-11-43-000-003) and (Ref. AMM TASK 36-11-43-400-003).
(6) Remove and discard the seal (2).
(7) Put a PLUG - BLANKING on the opening of the thermostat (3).

[Rev.10 from 2021] 2026.04.01 12:38:24 UTC