Inspection after Impact on Wing Tip/Fence

TASK 05-51-35-200-001-A
Inspection after Impact on Wing Tip/Fence

WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

1. Reason for the Job
This inspection is only applicable if the aircraft was stopped or in low speed movement.

NOTE: For all other conditions, it is necessary to refer to Airbus.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 4M (13 FT)
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)
98D27803500001	1	LOCKING TOOL ZERO POS

B. Referenced Information

REFERENCE	DESIGNATION
TASK 23-61-00-200-001-A	Resistance Check from the Tip to the Retainer and Bonding Check from the Retainer to the Aircraft Structure
TASK 23-61-41-000-001-A	Removal of the Static Discharger
TASK 23-61-41-400-001-A	Installation of the Static Discharger
TASK 33-41-00-040-001-A	Deactivation of the Glazing Panel of the Wing-Tip Navigation Light
TASK 33-41-00-710-001-A	Operational Test of the Navigation Lights
TASK 33-48-00-710-001-A	Operational Test of the Anti-Collision Lighting
TASK 33-48-11-000-001-A	Removal of the Upper Beacon/Strobe Light from the Outside of the Fuselage
TASK 57-30-00-200-001-A	Detailed Inspection of Wing Tip, Bottom Skin Lower Surface Joint, Outboard of RIB27
TASK 57-31-00-040-001-A	Deactivation of the Wing-Tip Fence
TASK 57-31-21-000-001-A	Removal of the Wing-Tip Structure
TASK 57-31-21-400-001-A	Installation of the Wing-Tip Structure
TASK 57-31-22-000-001-A	Removal of the Wing-Tip Fence
TASK 57-31-22-400-001-A	Installation of the Wing-Tip Fence
TASK 57-37-12-000-802-A	Removal of the Navigation-Light Glazing Panel
TASK 57-37-12-400-802-A	Installation of the Navigation-Light Glazing Panel
SRM 572611
SRM 573121
SRM 573122
Wing Tip and Wing Tip Fence

3. Job Set-up
Subtask 05-51-35-941-050-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Install the 98D27803500001 LOCKING TOOL ZERO POS on the flap/slat control lever.
(2) Put WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
(3) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(4) Put an ACCESS PLATFORM 4M (13 FT) below the applicable wing-tip, zone 534(634).

4. Procedure
Subtask 05-51-35-210-050-A ** ON A/C NOT FOR ALL

A. Inspection of the Wing Tip/Fence after a Strike

Wing Tip and Wing Tip Fence ** ON A/C NOT FOR ALL

ITEM	INSPECTION TASKS	PHASE 1	PHASE 2
1.	Do a detailed visual inspection for signs of impact, distortion and pulled or loose fasteners on the items that follow: - The wing tip fence - The wing tip - The wing-to-wing-tip joint - At the upper surface joint - At the lower-skin lower surface joint (Ref. AMM TASK 57-30-00-200-001).	X
A.	If you find damage on the wing tip fence:
	- Repair the fence SRM 573122.		X
	- Or replace the fence (Ref. AMM TASK 57-31-22-000-001) (Ref. AMM TASK 57-31-22-400-001).		X
	- Or do the deactivation of the wing tip fence (Ref. AMM TASK 57-31-00-040-001).		X
B.	If the damage to the wing tip fence is more than the permitted damage limits SRM 573122:
	- Remove the fence (Ref. AMM TASK 57-31-22-000-001).		X
	- Do a detailed visual inspection of the fence attachment fittings on the wing tip SRM 573122.		X
C.	If you find damage on the wing tip:
	- Repair the wing tip SRM 573121.	X
	- Or replace the wing tip (Ref. AMM TASK 57-31-21-000-001) and (Ref. AMM TASK 57-31-21-400-001).	X
D.	If the wing tip is bent or has distortion, or if there is damage on the internal structure:
	- Remove the wing tip (Ref. AMM TASK 57-31-21-000-001).		X
	- Do a detailed visual inspection of the wing-to-wing-tip attachment fittings SRM 572611.		X
E.	If there is damage on the wing-to- wing-tip joint:
	- Remove the wing tip (Ref. AMM TASK 57-31-21-000-001).		X
	- Do a detailed visual inspection of the wing-to-wing-tip attachment fittings SRM 572611.		X
2.	Do a detailed visual inspection of the navigation light glazing (Ref. AMM TASK 33-41-00-040-001).	X
A.	If you find damage:
	- Repair the glazing (Ref. AMM TASK 33-41-00-040-001) or replace it (Ref. AMM TASK 57-37-12-000-802) and (Ref. AMM TASK 57-37-12-400-802).		X
	- Do a test of the navigation light (Ref. AMM TASK 33-41-00-710-001).		X
	- Do a test of the anti-collision/ strobe light (Ref. AMM TASK 33-48-00-710-001). If necessary, remove the anti- collision/strobe light (Ref. AMM TASK 33-48-11-000-001).		X
3.	Examine the static dischargers and retainers for damage (Ref. AMM TASK 23-61-00-200-001).	X
A.	If you find damage:
	- Replace the static dischargers (Ref. AMM TASK 23-61-41-000-001) and (Ref. AMM TASK 23-61-41-400-001). NOTE : 20% of the static dischargers can be not in operation or missing from each wing.		X

5. Close-up
Subtask 05-51-35-942-050-A ** ON A/C NOT FOR ALL

A. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the 98D27803500001 LOCKING TOOL ZERO POS from the flap/slat control lever.
(3) Remove the WARNING NOTICE(S).
(4) Make sure that the work area is clean and clear of tools and other items.
(5) Remove the access platform(s).
(6) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.03.31 22:51:55 UTC