Resistance Check from the Tip to the Retainer and Bonding Check from the Retainer to the Aircraft Structure

TASK 23-61-00-200-001-A
Resistance Check from the Tip to the Retainer and Bonding Check from the Retainer to the Aircraft Structure

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

ZONE: 300
ZONE: 500
ZONE: 600

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ABRASIVE - FINE WIRE WOOL
No specific	1	ACCESS PLATFORM 12M (40 FT) - ADJUSTABLE
No specific	1	MEGOHMMETER 500 MOHMS
No specific	AR	SAFETY BARRIER(S)
No specific	1	SPONGE
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
300	STABILIZERS AND TAIL UNIT
500	LEFT WING
600	RIGHT WING

C. Referenced Information

REFERENCE	DESIGNATION
TASK 20-28-00-869-002-A	Table of the Maximum Permitted Resistance-Values
Static Dischargers ** ON A/C NOT FOR ALL
Static Dischargers ** ON A/C NOT FOR ALL
Static Dischargers ** ON A/C NOT FOR ALL
Static Dischargers ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 23-61-00-941-050-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Put the ACCESS PLATFORM 12M (40 FT) - ADJUSTABLE in position below the applicable zone.
(3) Put the WARNING NOTICE(S) in position to tell persons not to operate the flight controls.

4. Procedure
Subtask 23-61-00-210-050-A

A. Inspection of the Static Dischargers
(1) Examine the static dischargers to make sure that:

There is no distortion.
There is no important damage to the covers.
There is no corrosion on the bases.
There is no damage to the tips.
The screws are tight and serviceable.
They are correctly attached.

NOTE: A small damage like cosmetic or superficial damage is permitted.

Subtask 23-61-00-750-051-A

B. Bonding Resistance
(1) Make sure that the bonding resistance between the static discharger retainer and the aircraft structure is correct (Ref. AMM TASK 20-28-00-869-002).
(2) For the bonding resistance between the static discharger tip and the static discharger retainer:
(a) Measure the resistance between the tip of the static discharger and the static discharger retainer (with the MEGOHMMETER 500 MOHMS set to 500 VDC) as follows:

Connect one probe to the tip of the applicable static discharger.
Put the other probe against the side of the applicable static discharger retainer.
With one lead attached to the retainer, attach the other lead to a piece of wet SPONGE or the ABRASIVE - FINE WIRE WOOL (to touch the tip of the static discharger).

(b) Measure the resistance values that follow:

For type A, between 6 and 120 megohms
For type B, between 6 and 200 megohms.

5. Close-up
Subtask 23-61-00-942-050-A

A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety barriers.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 04:05:17 UTC