Removal of the Overpressure Valve

TASK 36-11-53-000-001-A
Removal of the Overpressure Valve

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

ZONE: 471
ZONE: 481
FIN: 5HA1 ** ON A/C NOT FOR ALL
FIN: 5HA2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	CAP - BLANKING
No specific	AR	COVER - PROTECTION
No specific	AR	PLUG - BLANKING
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
471	PYLON LEADING EDGE
481	PYLON LEADING EDGE
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 36-11-49-000-014-A	Removal of the Duct Assy
TASK 49-00-00-860-006-A	APU Shutdown by External Power
TASK 49-00-00-860-006-A-01	APU Shutdown by Batteries
TASK 49-00-00-860-009-A	APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01	APU Shutdown by Batteries (131-9(A))
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
Overpressure Valve ** ON A/C NOT FOR ALL
Overpressure Valve ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 36-11-53-861-051-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002) or (Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-53-941-050-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Make sure that the engine 1(2) shut down occured not less than 5 minutes before you do this procedure.
(2) On the AIR COND panel 30VU:

make sure that the ENG 1(2) BLEED pushbutton switch is released (the OFF legend is on),
make sure that the APU BLEED pushbutton switch is released (the ON legend is off),
put a WARNING NOTICE(S) to tell persons not to operate the pneumatic system.

(3) On the ENG panel 115VU:

put a WARNING NOTICE(S) to tell persons not to start the engine 1(2).

(4) On the HP ground connector:

Put a WARNING NOTICE(S) to tell persons not to pressurize the pneumatic system.

(5) On the ENG section of the maintenance panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 36-11-53-010-050-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in position below the engine.

Subtask 36-11-53-040-051-A ** ON A/C NOT FOR ALL

D. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).

Subtask 36-11-53-010-053-A ** ON A/C NOT FOR ALL

E. Open the thrust reverser doors (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 36-11-53-010-050-B ** ON A/C NOT FOR ALL

F. Get Access
(1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in position below the engine.

Subtask 36-11-53-040-051-B ** ON A/C NOT FOR ALL

G. Deactivate the Thrust Reverser Hydraulic Control Unit

WARNING: MAKE SURE THAT THE THRUST REVERSER HYDRAULIC CONTROL UNIT (HCU) IS DEACTIVATED BEFORE YOU DO WORK ON OR AROUND THE THRUST REVERSER. IF THE HCU IS NOT DEACTIVATED, THERE IS A RISK OF UNWANTED THRUST REVERSER OPERATION WHICH CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Deactivate the thrust reverser Hydraulic Control Unit (HCU) (Ref. AMM TASK 78-30-00-040-012).

Subtask 36-11-53-010-053-B ** ON A/C NOT FOR ALL

H. Open the thrust reverser halves (Ref. AMM TASK 78-32-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR

4. Procedure

CAUTION: SOME PRESSURE CAN STAY IN THE DUCTING. THE PRESSURE WILL DECREASE WHEN YOU RELEASE THE CLAMPS.

Subtask 36-11-53-020-054-A ** ON A/C NOT FOR ALL

A. Removal of the Overpressure Valve
(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM TASK 49-00-00-860-006)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

CAUTION: USE A SECOND WRENCH TO APPLY COUNTER TORQUE TO THE UNION ON THE VALVE WHEN YOU CONNECT THE HP SENSE TUBE.

(3) Disconnect the electrical connector (3).
(4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(5) Remove the clamp (5).
(6) Hold the valve (6) and remove the clamp (2).
(7) Remove the valve (6).
(8) Put a COVER - PROTECTION on the valve (6) and the ducts.

Subtask 36-11-53-020-054-B ** ON A/C NOT FOR ALL

A. Removal of the Overpressure Valve
(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM D/O 49-00-00-86)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

CAUTION: USE A SECOND WRENCH TO APPLY COUNTER TORQUE TO THE UNION ON THE VALVE WHEN YOU CONNECT THE HP SENSE TUBE.

(3) Disconnect the electrical connectors (1), (2), (3) and (7).
(4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(5) Put the PLUG-BLANKING in each disconnected line end.
(6) Remove the screws (9) and the nuts (11) from the links (10).
(7) Disengage the links (10) from the duct (8).
(8) Remove the clamp (13) from the duct (8).
(9) Remove the duct assembly (14) (Ref. AMM TASK 36-11-49-000-014).
(10) Remove the duct (8).
(11) Hold the valve (6) and remove the clamp (5).
(12) Remove the valve (6).
(13) Put the COVER - PROTECTION on the valve (6) and the ducts.

[Rev.10 from 2021] 2026.04.01 06:38:35 UTC