Removal of the Duct Assy

TASK 36-11-49-000-014-A
Removal of the Duct Assy

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

FIN: 7125HM1 ** ON A/C NOT FOR ALL
FIN: 7125HM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	COVER - PROTECTION
No specific	AR	PLUG - BLANKING
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 49-00-00-860-009-A	APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01	APU Shutdown by Batteries (131-9(A))
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
Duct Assy
Duct Assy ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 36-11-49-861-079-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002) or (Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-49-941-094-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(2) On the AIR COND panel 30VU:

make sure that the ENG 1(2) BLEED pushbutton switch is released (the OFF legend is on),
make sure that the APU BLEED pushbutton switch is released (the ON legend is off),
put a WARNING NOTICE(S) in position to tell persons not to operate the pneumatic system.

(3) On the ENG panel 115VU:

put a WARNING NOTICE(S) in position to tell persons not to start the engine 1(2).

(4) On the HP ground connector:

put a WARNING NOTICE(S) in position to tell persons not to pressurize the pneumatic system.

(5) On the ENG section of the maintenance panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
put a WARNING NOTICE(S) in position to tell persons not to energize the FADEC 1(2).

Subtask 36-11-49-010-130-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position below the engine.

Subtask 36-11-49-040-099-A ** ON A/C NOT FOR ALL

D. Deactivate the Thrust Reverser.

WARNING: MAKE SURE THAT THE THRUST REVERSER HYDRAULIC CONTROL UNIT (HCU) IS DEACTIVATED BEFORE YOU DO WORK ON OR AROUND THE THRUST REVERSER. IF THE HCU IS NOT DEACTIVATED, THERE IS A RISK OF UNWANTED THRUST REVERSER OPERATION WHICH CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Deactivate the thrust reverser Hydraulic Control Unit (HCU) (Ref. AMM TASK 78-30-00-040-012)

Subtask 36-11-49-010-217-A ** ON A/C NOT FOR ALL

E. Open the thrust reverser halves (Ref. AMM TASK 78-32-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR.
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR.

4. Procedure
Subtask 36-11-49-020-091-B ** ON A/C NOT FOR ALL

A. Removal of the Duct Assy
(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM D/O 49-00-00-86)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

(3) Disconnect the sense lines (1) and (2).
(4) Put the PLUG-BLANKING in each disconnected line end.
(5) Hold the duct assy (4) and remove the clamps (3).
(6) Remove the duct assy (4).
(7) Put COVER - PROTECTION on the duct assy (4) and the ducts.

Subtask 36-11-49-020-091-C

A. Removal of the Duct Assy
(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM D/O 49-00-00-86)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

(3) Disconnect the sense line (1).
(4) Put the PLUG-BLANKING in each disconnected line end.
(5) Hold the duct assy (4) and remove the clamps (3).
(6) Remove the duct assy (4).
(7) Put COVER - PROTECTION on the duct assy (4) and the ducts.

[Rev.10 from 2021] 2026.04.01 01:11:06 UTC