Removal of Lavatory H (Design Lav. M)
TASK 25-43-44-000-003-A
Removal of Lavatory H (Design Lav. M)
Self Explanatory
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 25-43-44-861-051-A ** ON A/C NOT FOR ALL Subtask 25-43-44-680-051-A ** ON A/C NOT FOR ALL
Subtask 25-43-44-020-063-B ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:35:28 UTC
Removal of Lavatory H (Design Lav. M)
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY (MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
1. Reason for the JobSelf Explanatory
NOTE: More than one person is necessary for this procedure.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| No specific | 1 | CONTAINER 1 L (1/4 USGAL) |
| No specific | AR | PLUG - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 12-24-38-680-001-A | Draining of the Potable Water System (with Electrical Power) |
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 25-21-41-000-001-A | Removal of the Passenger Seats |
| TASK 25-23-41-000-001-A | Removal of the Ceiling Panels |
| TASK 25-23-43-000-001-A | Removal of the Upper Sidewall Panel |
| TASK 25-23-44-000-001-A | Removal of the Lower Sidewall Panels (Dado Panels) |
| TASK 25-23-48-000-001-A | Removal of the Cove Light Panel |
| TASK 25-33-42-000-001-A | Removal of the Aft Galley Unit |
| TASK 25-45-19-000-001-A | Removal of the Lavatory Door |
| TASK 25-45-22-000-001-A | Removal of the Toilet Shroud and the Seat |
| TASK 35-21-41-000-001-A | Removal of the Emergency Oxygen Containers |
| TASK 38-30-00-010-002-A | Removal of the Toilet Drain Lines |
| TASK 38-31-41-000-001-A | Removal of a Toilet Assembly |
Subtask 25-43-44-861-051-A ** ON A/C NOT FOR ALL Subtask 25-43-44-680-051-A ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
(1) Drain the potable water system (Ref. AMM TASK 12-24-38-680-001).
(2) Put the WARNING NOTICE(S) in position to tell persons not to do the servicing of the water system.
Subtask 25-43-44-865-064-A ** ON A/C NOT FOR ALL (1) Drain the potable water system (Ref. AMM TASK 12-24-38-680-001).
(2) Put the WARNING NOTICE(S) in position to tell persons not to do the servicing of the water system.
C. Open, safety and tag this(these) circuit breaker(s):
Subtask 25-43-44-865-070-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| 49VU | OXYGEN/PASSENGER/ACTUATION | 7WR | HA08 |
| 49VU | OXYGEN/PASSENGER/ACTUATION | 6WR | HA07 |
| 49VU | OXYGEN/PASSENGER/ACTUATION | 5WR | HA06 |
| 49VU | OXYGEN/PASSENGER/ACTUATION | 4WR | HA05 |
| 49VU | OXYGEN/PASSENGER/CTL AND WARN | 3WR | HA04 |
| 49VU | OXYGEN/PASSENGER/CTL AND WARN | 2WR | HA03 |
| 49VU | OXYGEN/PASSENGER/CTL AND WARN | 1WR | HA02 |
| 121VU | COM NAV/CIDS/DEU A NORM/R FWD | 164RH | M11 |
| 121VU | COM NAV/CIDS/DEU A NORM/L FWD | 163RH | M10 |
| 122VU | AIR COND/LAV/GALLEY VENT CTL/EXTRACT FAN/CTL | 5HU | U21 |
| 122VU | AIR COND/LAV/GALLEY VENT CTL/EXTRACT FAN/SPLY | 6HU | U19 |
| 2000VU | POT WIP-HEATER-CTL | 2DW | A01 |
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| 2001VU | VACU TOIL SYS-VACUUM-GEN | 33MG | A08 |
| 2001VU | VACU TOIL SYS-VACU-SYS | 35MG | A06 |
| 2001VU | VACU TOIL SYS-LAV PWR-L | 45MG | A02 |
| 2001VU | WATER SYS-QUANT-IND | 1MA | B06 |
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
| 2001VU | LAV AFT-HOT WATER-D/L | 2MB | B02 |
D. Open, safety and tag this(these) circuit breaker(s):
Subtask 25-43-44-010-069-K ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | POT WIP-HEATER-CTL | 2DW | A01 |
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| 2001VU | VACU TOIL SYS-VACUUM-GEN | 33MG | A08 |
| 2001VU | VACU TOIL SYS-VACU-SYS | 35MG | A06 |
| 2001VU | VACU TOIL SYS-LAV PWR-L | 45MG | A02 |
| 2001VU | WATER SYS-QUANT-IND | 1MA | B06 |
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
| 2001VU | LAV AFT-HOT WATER-D/L | 2MB | B02 |
E. Get Access
(1) Remove the passenger seat adjacent to the lavatory (Ref. AMM TASK 25-21-41-000-001).
(2) Remove the galley (Ref. AMM TASK 25-33-42-000-001).
(3) Remove the ceiling panels (Ref. AMM TASK 25-23-41-000-001).
(4) Remove the cove light panel (Ref. AMM TASK 25-23-48-000-001).
(5) Remove the upper sidewall panel (Ref. AMM TASK 25-23-43-000-001).
(6) Remove the lower sidewall panel (Ref. AMM TASK 25-23-44-000-001).
(7) Remove the lavatory door (Ref. AMM TASK 25-45-19-000-001).
(8) Remove the toilet assembly (Ref. AMM TASK 38-31-41-000-001).
(9) Remove the toilet shroud (Ref. AMM TASK 25-45-22-000-001).
(10) Remove the toilet drain line, installed behind the lavatory (Ref. AMM TASK 38-30-00-010-002).
(11) In the lavatory, remove the emergency oxygen container 34WR1 (Ref. AMM TASK 35-21-41-000-001).
4. Procedure(1) Remove the passenger seat adjacent to the lavatory (Ref. AMM TASK 25-21-41-000-001).
(2) Remove the galley (Ref. AMM TASK 25-33-42-000-001).
(3) Remove the ceiling panels (Ref. AMM TASK 25-23-41-000-001).
(4) Remove the cove light panel (Ref. AMM TASK 25-23-48-000-001).
(5) Remove the upper sidewall panel (Ref. AMM TASK 25-23-43-000-001).
(6) Remove the lower sidewall panel (Ref. AMM TASK 25-23-44-000-001).
(7) Remove the lavatory door (Ref. AMM TASK 25-45-19-000-001).
(8) Remove the toilet assembly (Ref. AMM TASK 38-31-41-000-001).
(9) Remove the toilet shroud (Ref. AMM TASK 25-45-22-000-001).
(10) Remove the toilet drain line, installed behind the lavatory (Ref. AMM TASK 38-30-00-010-002).
(11) In the lavatory, remove the emergency oxygen container 34WR1 (Ref. AMM TASK 35-21-41-000-001).
Subtask 25-43-44-020-063-B ** ON A/C NOT FOR ALL
A. Removal of the Pelmet
(1) Remove the screws (3) and the washers (2), lift and remove the pelmet (1).
Subtask 25-43-44-020-064-A ** ON A/C NOT FOR ALL (1) Remove the screws (3) and the washers (2), lift and remove the pelmet (1).
B. Removal of the Electrical Connections:
(1) On the lavatory ceiling, disconnect the electrical connector (10).
(2) Open the sanitary-cabinet access door (3).
(3) Disconnect the electrical connectors (7), (8), (9) and (11).
(4) Remove and discard the cable ties (6) from the mounts (5).
(5) Remove the screws (12), the washers (13) and remove the bracket (14).
(6) Disconnect the electrical connectors from the flush switch (1).
(7) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(8) Close the sanitary-cabinet access door (3).
Subtask 25-43-44-020-065-B ** ON A/C NOT FOR ALL (1) On the lavatory ceiling, disconnect the electrical connector (10).
(2) Open the sanitary-cabinet access door (3).
(3) Disconnect the electrical connectors (7), (8), (9) and (11).
(4) Remove and discard the cable ties (6) from the mounts (5).
(5) Remove the screws (12), the washers (13) and remove the bracket (14).
(6) Disconnect the electrical connectors from the flush switch (1).
(7) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(8) Close the sanitary-cabinet access door (3).
C. Removal of the Air Connections
(1) Disconnect the air extraction connections:
(a) Above the lavatory ceiling, loosen the clamp (2) and disconnect the air extraction hose (1).
(2) Disconnect the ventilation hoses:
(a) Behind the lavatory, loosen the clamps (10) and (12) and disconnect the ventilation hoses (9) and (8).
(b) Remove the screws (4), washers (5), spacers (7) and clamps (6).
(c) Put the PLUG-BLANKING in each disconnected line end.
Subtask 25-43-44-020-066-B ** ON A/C NOT FOR ALL (1) Disconnect the air extraction connections:
(a) Above the lavatory ceiling, loosen the clamp (2) and disconnect the air extraction hose (1).
(2) Disconnect the ventilation hoses:
(a) Behind the lavatory, loosen the clamps (10) and (12) and disconnect the ventilation hoses (9) and (8).
(b) Remove the screws (4), washers (5), spacers (7) and clamps (6).
(c) Put the PLUG-BLANKING in each disconnected line end.
D. Removal of the Water Connections
(2) Put a CONTAINER 1 L (1/4 USGAL) in position below the water connections that you will disconnect.
(3) Disconnect the potable water connections:
(a) Remove the nut (5) and the washer (6) and disconnect the bonding straps (4).
(b) Loosen the nut (2) and disconnect the potable water tube (3) from the fitting (7).
(c) Loosen the nuts (2) and remove the potable water hose (8).
(d) Put the PLUG-BLANKING in each disconnected line end.
(4) Disconnect the waste-water drain connection:
(b) Remove the screw (15), washer(s) (14), nut (13) and clamp (12).
(c) Put the PLUG-BLANKING in each disconnected line end.
Subtask 25-43-44-020-067-B ** ON A/C NOT FOR ALL WARNING:
DO NOT DO WORK ON THE TOILET WASTE SYSTEM AND THE POTABLE WATER SYSTEM AT THE SAME TIME. THIS WILL PREVENT CONTAMINATION OF THE POTABLE WATER SYSTEM. SUCH CONTAMINATION CAN BE DANGEROUS TO HEALTH.
WARNING:
MAKE SURE THAT THE EQUIPMENT YOU USE FOR THIS PROCEDURE IS CLEAN AND APPROVED FOR THE POTABLE WATER SYSTEM. IF NOT IT CAN CAUSE CONTAMINATION OF THE POTABLE WATER SYSTEM.
WARNING:
BEFORE YOU DO WORK ON THE POTABLE WATER SYSTEM, CLEAN YOUR HANDS WITH SOAP AND WATER. THIS WILL PREVENT INFECTION. (CONTAMINATION FROM TOILET WASTE IS DANGEROUS TO HEALTH).
(1) Open the sanitary-cabinet access door (1). (2) Put a CONTAINER 1 L (1/4 USGAL) in position below the water connections that you will disconnect.
(3) Disconnect the potable water connections:
(a) Remove the nut (5) and the washer (6) and disconnect the bonding straps (4).
(b) Loosen the nut (2) and disconnect the potable water tube (3) from the fitting (7).
(c) Loosen the nuts (2) and remove the potable water hose (8).
(d) Put the PLUG-BLANKING in each disconnected line end.
(4) Disconnect the waste-water drain connection:
CAUTION:
MAKE MATCH MARK ON THE WASTE WATER AND AIR OUTLET HOSES AND ON THEIR RELATED CONNECTIONS.
IF YOU CONNECT ONE OF THESE HOSES TO THE CONNECTION OF THE OTHER HOSE, YOU CAN CAUSE DAMAGE TO EQUIPMENT.
(a) Loosen the clamps (9) and disconnect the sleeve (10) from the drain tube (11). (b) Remove the screw (15), washer(s) (14), nut (13) and clamp (12).
(c) Put the PLUG-BLANKING in each disconnected line end.
E. Removal of the Upper Attachment(s)
(1) Remove the panel (1).
(2) Remove the quick-release pin (2) and disconnect the tie rod (5) from the aircraft structure.
Subtask 25-43-44-020-068-D ** ON A/C NOT FOR ALL (1) Remove the panel (1).
(2) Remove the quick-release pin (2) and disconnect the tie rod (5) from the aircraft structure.
F. Removal of the Lower Attachments
(1) Remove the covers (5).
(2) Remove the bolts (9), the washers (8), the bushes (7) and (6) and the lavatory module.
(3) Remove the screws (4), the pins (1), the stoppers (3) and the fittings (2) from the seat tracks.
Subtask 25-43-44-020-069-B ** ON A/C NOT FOR ALL (1) Remove the covers (5).
(2) Remove the bolts (9), the washers (8), the bushes (7) and (6) and the lavatory module.
(3) Remove the screws (4), the pins (1), the stoppers (3) and the fittings (2) from the seat tracks.
G. Disassembly of the Lavatory
(1) Remove the sealant from around the floor pan assembly (1).
(2) Remove the screws (2) and the washers (3).
(3) Remove the screws (4) and the washers (5).
(4) Lift and remove the lavatory assemblies (11) and (12) from the floor pan assembly (1).
(5) Remove the screws (7), (9) and (16), washers (8) and (15) and ceiling panel (6).
(6) Remove the screw (10).
(7) Remove the screws (13) and the washers (14).
(8) Remove the lavatory assemblies (11) and (12) from the aircraft.
Subtask 25-43-44-020-070-B ** ON A/C NOT FOR ALL (1) Remove the sealant from around the floor pan assembly (1).
(2) Remove the screws (2) and the washers (3).
(3) Remove the screws (4) and the washers (5).
(4) Lift and remove the lavatory assemblies (11) and (12) from the floor pan assembly (1).
(5) Remove the screws (7), (9) and (16), washers (8) and (15) and ceiling panel (6).
(6) Remove the screw (10).
(7) Remove the screws (13) and the washers (14).
(8) Remove the lavatory assemblies (11) and (12) from the aircraft.
H. Removal of the Floor Pan Assembly
(1) If installed, remove the screws (4) from the floor angle brackets (5).
(2) If installed, remove the rubber strips (6), (8) and (9) from the floor panel (7).
(3) Remove the screws (3), door sill (2) and floor pan assembly (1).
(1) If installed, remove the screws (4) from the floor angle brackets (5).
(2) If installed, remove the rubber strips (6), (8) and (9) from the floor panel (7).
(3) Remove the screws (3), door sill (2) and floor pan assembly (1).
Pelmet