Detailed Inspection of Aft Passenger/Crew Door, Internal Structure, LH/RH

TASK 52-13-00-200-002-A
Detailed Inspection of Aft Passenger/Crew Door, Internal Structure, LH/RH

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 832
ZONE: 842

1. Reason for the Job
Refer to the MPD TASK: 521304-01
DETAILED INSPECTION OF AFT PASSENGER/CREW DOOR, INTERNAL STRUCTURE, LH/RH

NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the MPD task applicability. The information on weight variant groups is given in the MPD and SRM introductions.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	SCRAPER - PLASTIC

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05TAD1)	Adhesive Tape-- Uncoated Cloth -
(Material No.05TDB1)	Adhesive Tape-Wear Protection Flame Retardant -
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ADB1)	Corrosion Preventive Compound-Water Displacing & Heavy Duty Hard Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
832	AFT PASSENGER/CREW DOOR
842	AFT PASSENGER/CREW DOOR
832AZ, 832BZ, 832CZ, 832DZ, 832EZ, 842AZ, 842BZ, 842CZ, 842DZ, 842EZ

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
2	SELF-HOCKING TAPE	AIPC 52-13-11-23-040
1	SELF-HOCKING TAPE	AIPC 52-13-11-23-370
2	SELF-HOCKING TAPE	AIPC 52-13-84-25-200
1	SELF-HOCKING TAPE	AIPC 52-13-84-25-210

E. Referenced Information

REFERENCE	DESIGNATION
TASK 25-23-46-000-002-A	Removal of the Door Linings from the Aft Passenger/Crew Doors
TASK 25-23-46-400-002-A	Installation of the Door Linings on the Aft Passenger/Crew Doors
TASK 25-62-44-000-002-A	Removal of the Left Escape-Slide Pack-Assembly
TASK 25-62-44-000-012-A	Removal of the Left-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-000-802-A	Removal of the Right Escape-Slide Pack-Assembly
TASK 25-62-44-000-804-A	Removal of the Right-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-400-006-A	Installation of the Left Escape-Slide Pack-Assembly
TASK 25-62-44-400-007-A	Installation of the Left-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-62-44-400-802-A	Installation of the Right Escape-Slide Pack-Assembly
TASK 25-62-44-400-803-A	Installation of the Right-Hand Escape-Slide-Raft Pack-Assembly
TASK 25-80-00-000-001-A	Removal of the Insulation Blankets
TASK 25-80-00-400-001-A	Installation of the Insulation Blankets
TASK 51-78-00-916-001-A	Application of Temporary Protection System (TPS)
TASK 52-10-00-010-001-A	Opening of the Passenger/Crew Door
TASK 52-10-00-410-001-A	Closing of the Passenger/Crew Door
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
SRM 511100	(for corrective action)
SRM 512200	(for corrective action)
Internal Structure of the Aft Passenger/Crew Door, Left and Right Sides

3. Job Set-up
Subtask 52-13-00-010-055-A

A. Get Access
(1) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position:
(a) For the left passenger/crew door, at zone 832
(b) For the right passenger/crew door, at zone 842.
(2) Open the applicable aft passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start the work on the door (Ref. AMM TASK 52-10-00-860-001).
(4) Remove the door lining panels (Ref. AMM TASK 25-23-46-000-002):
(a) For the left door:

832DZ 832EZ 832CZ 832AZ and 832BZ.

(b) For the right door:

842DZ 842EZ 842CZ, 842AZ and 842BZ.

Subtask 52-13-00-020-051-A ** ON A/C NOT FOR ALL

B. Removal of the Components
(1) Remove the escape slide:
(a) For the left door:

If installed, remove the left escape slide pack-assembly (Ref. AMM TASK 25-62-44-000-002).

(b) For the right door:

If installed, remove the right escape slide pack-assembly (Ref. AMM TASK 25-62-44-000-802).

(2) Identify and remove the related insulation blankets from the inspection area (Ref. AMM TASK 25-80-00-000-001).
(3) Remove the pressure-sensitive fabric tape with the SCRAPER - PLASTIC.
(4) Remove the self-hocking tapes (1) and (2) with the SCRAPER - PLASTIC.

Subtask 52-13-00-020-051-B ** ON A/C NOT FOR ALL

B. Removal of the component

Internal Structure of the Aft Passenger/Crew Door, Left and Right Sides ** ON A/C NOT FOR ALL

(1) Remove the escape slide:
(a) For the left door:
If installed, remove the left-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-000-012).
(b) For the right door:
If installed, remove the right-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-000-804).
(2) Identify and remove the related insulation blankets from the inspection area (Ref. AMM TASK 25-80-00-000-001).
(3) Remove the fabric tape pressure sensitive with SCRAPER - PLASTIC.
(4) Remove the self-hocking tape (1) and (2) with SCRAPER - PLASTIC.

Subtask 52-13-00-110-051-A

C. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
(3) If there is a TPS layer and if it does not let you do a satisfactory inspection, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).

4. Procedure
Subtask 52-13-00-220-053-A

A. Inspection
(1) Do a detailed inspection of:

The internal structure
The inner skin
The vertical curved members
The longerons of the passenger/crew door for damage or discontinuities.

(2) Make sure that there is no:
(a) Corrosion damage:
If you find corrosion, refer to the Structural Repair Manual ( SRM 512200) for the corrosion types, inspection, removal and subsequent corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
If you find this type of damage, refer to the Structural Repair Manual ( SRM 511100) for the damage types, classification and corrective action.

Subtask 52-13-00-916-051-A

B. Check and Application of the TPS Layer

CAUTION: DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) TYPE 3 ON THE MOVABLE COMPONENTS. USE ONLY TPS TYPE 1 GRADE 2. IF YOU DO NOT OBEY THIS INSTRUCTION, THE MECHANISMS WILL NOT OPERATE CORRECTLY.

(1) If the TPS was removed at the "Preparation of the Inspection Area", apply a new layer of Corrosion Preventive Compound-Water Displacing & Heavy Duty Hard Film - (Material No.12ADB1) (Ref. AMM TASK 51-78-00-916-001).
(2) If the TPS was not removed at the "Preparation of the Inspection Area", do a check of the condition and integrity of the TPS layer (Ref. AMM TASK 51-78-00-916-001).
(3) If the TPS layer has local damage, remove the damaged TPS layer and apply a new layer of Corrosion Preventive Compound-Water Displacing & Heavy Duty Hard Film - (Material No.12ADB1) (Ref. AMM TASK 51-78-00-916-001).

NOTE: If, after the check of the condition and integrity, the TPS layer is in the correct condition, Airbus recommends that you apply a new layer as a spray on the existing layer. This is to make sure that the TPS layer continues to give satisfactory corrosion protection.

5. Close-up
Subtask 52-13-00-420-051-A ** ON A/C NOT FOR ALL

A. Installation of the Components
(1) Install the new AIPC 52-13-11-23-370 SELF-HOCKING TAPE (1) or the new AIPC 52-13-84-25-210 SELF-HOCKING TAPE (1) and the new AIPC 52-13-11-23-040 SELF-HOCKING TAPE (2) or the new AIPC 52-13-84-25-200 SELF-HOCKING TAPE (2).
(2) Cut the Adhesive Tape-- Uncoated Cloth - (Material No.05TAD1) or the Adhesive Tape-Wear Protection Flame Retardant - (Material No.05TDB1) with a overlap span of 10 mm (0.39 in.) in the internal edge of the holes.
(3) Install the Adhesive Tape-- Uncoated Cloth - (Material No.05TAD1) or the Adhesive Tape-Wear Protection Flame Retardant - (Material No.05TDB1) .
(4) Install the removed insulation blankets (Ref. AMM TASK 25-80-00-400-001).
(5) Install the escape slide:
(a) For the left door:

If removed, install the left escape slide pack-assembly (Ref. AMM TASK 25-62-44-400-006).

(b) For the right door:

If removed, install the right escape slide pack-assembly (Ref. AMM TASK 25-62-44-400-802).

Subtask 52-13-00-420-051-B ** ON A/C NOT FOR ALL

A. Installation of the Component
(1) Install the new AIPC 52-13-11-23-370 SELF-HOCKING TAPE (1) and new AIPC 52-13-11-23-040 SELF-HOCKING TAPE (2).
(2) Cut the Adhesive Tape-- Uncoated Cloth - (Material No.05TAD1) or the Adhesive Tape-Wear Protection Flame Retardant - (Material No.05TDB1) with a span overlap of 10 mm (0.39 in.) in internal edge of holes.
(3) Install the Adhesive Tape-- Uncoated Cloth - (Material No.05TAD1) or the Adhesive Tape-Wear Protection Flame Retardant - (Material No.05TDB1) .
(4) Install the removed insulation blankets (Ref. AMM TASK 25-80-00-400-001).
(5) Install the escape slide:
(a) For the left door:
If removed, install the left-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-400-007).
(b) For the right door:
If removed, install the right-hand escape slide raft pack assembly (Ref. AMM TASK 25-62-44-400-803).

Subtask 52-13-00-410-059-A

B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the door lining panels (Ref. AMM TASK 25-23-46-400-002):
(a) For the left door:

832DZ 832EZ 832CZ 832AZ and 832BZ.

(b) For the right door:

842DZ 842EZ 842CZ 842AZ and 842BZ.

(3) Obey the special precautions after you completed the work on the door (Ref. AMM TASK 52-10-00-860-002).
(4) Close the applicable aft passenger/crew door (Ref. AMM TASK 52-10-00-410-001).
(5) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.01 04:11:13 UTC