Operational test of the Cursor Control Device (CCD)

TASK 31-61-00-710-801-A
Operational test of the Cursor Control Device (CCD)

ZONE: 211
ZONE: 212

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
211	COCKPIT
212	COCKPIT

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure
TASK 34-10-00-860-004-A	Inertial Reference (IR) Alignment-Procedure
TASK 34-10-00-860-004-A-01	Automatic Inertial Reference (IR) Alignment-Procedure
TASK 34-10-00-860-004-A-02	Inertial Reference (IR) Alignment-Procedure to do a Check of the Links between each Flight Management and Guidance Computer (FMGC) and the three Air Data/Inertial Reference Units (ADIRUs)
TASK 34-10-00-860-005-A	ADIRS Stop Procedure

3. Job Set-up
Subtask 31-61-00-860-051-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Do the EIS start procedure (upper ECAM DU and lower ECAM DU only)
(Ref. AMM TASK 31-60-00-860-001).
(3) Do the IR alignment procedure (Ref. AMM TASK 34-10-00-860-004).

Subtask 31-61-00-865-052-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	OANS CMPTR	2FX	L10
FOR FIN: 35WT (CCD CAPTAIN)
121VU	OANS CCD CAPT	37WT	L11
FOR FIN: 36WT (CCD FIRST OFFICER)
121VU	OANS CCD F/O	38WT	L09

4. Procedure
Subtask 31-61-00-710-051-A ** ON A/C NOT FOR ALL

A. Operational Test of the CCD

ACTION	RESULT
1.On the FCU, on the CAPT and F/O EFIS control panels:	On the CAPT and F/O NDs:
Set the scale selector switch to ZOOM position.
NOTE: To use the ZOOM function, turn the scale switch some degrees counterclockwise.
Set the mode selector switch to NAV position.	In the top part of the NDs, the airport map comes into view (if ADB is already loaded). On this map, the aircraft symbol shows the current aircraft position on the airport surface.
2.On the CAPT and F/O CCDs:
	In the NDs, the cursor comes into view.
Move the CCD trackball.	The cursor moves correctly.
Push the CCD validation pushbutton switch.	The related symbol is highlighted.
Push the escape key.	The related symbol is no more highlighted.
3.On the FCU, on the CAPT and F/O EFIS control panels:
Set the scale selector switch clockwise to 10NM.	The airport map goes out of view.

5. Close-up
Subtask 31-61-00-860-052-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Do the ADIRS stop procedure (Ref. AMM TASK 34-10-00-860-005).
(2) Do the EIS stop procedure
(Ref. AMM TASK 31-60-00-860-002).
(3) Make sure that the aircraft electrical circuits are de-energized
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 08:43:46 UTC