Uploading of DMC1 Operational Software

TASK 31-60-00-610-803-C
Uploading of DMC1 Operational Software

ZONE: 210
FIN: 1WT1 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-38-00-610-804-A	Onboard Software Uploading Procedure
TASK 31-60-00-740-011-A	LRU Identification Check
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure

3. Job Set-up
Subtask 31-60-00-861-062-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 31-60-00-860-117-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration
(1) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).

Subtask 31-60-00-960-053-A ** ON A/C NOT FOR ALL

C. Prepare the media disk(s).
(1) Get the media disk(s) from the storage box in the cockpit.
(2) Make sure that the media disk(s) is(are) the correct one(s) for the aircraft configuration.
(a) Make sure that the Part Number (P/N) written on the media disk(s) is same the same as the P/N written in the airline configuration-management document.
1 If the media disk(s) is (are) not available or not the correct one(s), contact your Airline Engineering Department to get the correct part number(s) applicable to the aircraft.

Subtask 31-60-00-865-082-A ** ON A/C NOT FOR ALL

D. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	AUTO FLT/MCDU/1	11CA1	B01
49VU	L/G/LGCIU/SYS1/NORM	1GA	C09
49VU	EIS/ECAM/CTL/PNL	15WT	E12
49VU	EIS/DMC1/SPLY	10WT1	E11
49VU	EIS/DMC3/STBY/SPLY	14WT1	E10
49VU	EIS/DMC1/SWTG	21WT1	E09
49VU	EIS/DMC3/SWTG	21WT3	E07
121VU	DATA/LOADER/SPLY	3TD	J16
121VU	DLS&/DLRB/SPLY	5TD	J15
121VU	AUTO FLT/MCDU/2	11CA2	N20
121VU	EIS/DMC3/SPLY	10WT3	Q09
121VU	EIS/DMC2/SPLY	10WT2	Q08
121VU	EIS/DMC2/SWTG	21WT2	R08

Subtask 31-60-00-860-136-A ** ON A/C NOT FOR ALL

E. Make sure that the aircraft is in the ground configuration:

ACTION	RESULT
1.On the ECAM control panel: Push the BLEED key to get the BLEED page.	On the lower ECAM DU: The BLEED page comes into view. The white GND indication comes into view in the middle area of the page.

Subtask 31-60-00-280-060-A ** ON A/C NOT FOR ALL

F. Do a Check of the Part Number (P/N) of the Operational Software that you will upload in DMC1
(1) Do a check of the P/N of the DMC1 operational software (Ref. AMM TASK 31-60-00-740-011).
(a) On the DMC1 LRU IDENTIFICATION 1/5 page, read the P/N of the DMC1 operational software.
(b) Make sure that the P/N of the DMC1 operational software given on the DMC1 LRU IDENTIFICATION 1/5 page is different from the P/N of the DMC1 operational software written on the media disk(s).

4. Procedure
Subtask 31-60-00-970-052-A ** ON A/C NOT FOR ALL

A. Uploading of the Display Management Computer (DMC) 1 Operational Software with the Multipurpose Disk Drive Unit (MDDU)
(1) Upload the DMC1 operational software (Ref. AMM TASK 31-38-00-610-804).

Subtask 31-60-00-280-061-A ** ON A/C NOT FOR ALL

B. Check of the Part Number (P/N) of the Operational Software Uploaded in DMC1
(1) Do a check of the P/N of the DMC1 operational software (Ref. AMM TASK 31-60-00-740-011).
(a) On the DMC1 LRU IDENTIFICATION 1/5 page, read the P/N of the DMC1 operational software.
(b) Make sure that the P/N of the DMC1 operational software is the same as the P/N of the DMC1 operational software written on the media disk(s).

Subtask 31-60-00-280-062-A ** ON A/C NOT FOR ALL

C. Check of the Part Number (P/N) of the DMC1 Operational Software in the Equipment Configuration Report
(1) On the MCDU MENU page, push the line select key adjacent to the CFDS indication.
(2) On the MAINTENANCE MENU page, push the line select key adjacent to the AVIONICS CONFIG REPORTS indication.
(3) On the AVIONICS CONFIG REPORTS page, push the line select key adjacent to the STA indication.
(4) On the AVIONICS CONFIG REPORTS page, push the line select key adjacent to the EQUIPMENT CONFIG REPORTS indication.
(5) If the printer is on, push the PRINT key.
(6) If the printer is not on, on the EQUIPMENT CONFIG REPORTS page, push the line select key adjacent to the ATA316334 DMC1 indication.
(7) On the EQUIPMENT CONFIGURATION REPORT/ATA316334 DMC1 page, make sure that the correct software (software DB/N1) component is uploaded.
(8) Push the line select key adjacent to the RETURN indication until the MAINTENANCE 1/2 page comes into view.

5. Close-up
Subtask 31-60-00-860-118-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) On the MCDU:

Push the MCDU MENU key to get the MCDU MENU page.
Set the BRT knob to OFF.

(2) Put the media disk(s) back into the storage box in the cockpit.
(3) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).

Subtask 31-60-00-862-062-A ** ON A/C NOT FOR ALL

B. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 00:37:49 UTC