Installation of the Removable SIM Module (RSM) and the SIM Module I/O Cards (SMIO) of the WGL-DAR

TASK 31-36-00-400-803-A
Installation of the Removable SIM Module (RSM) and the SIM Module I/O Cards (SMIO) of the WGL-DAR

CAUTION: OBEY THESE PRECAUTIONS TO PREVENT ELECTROSTATIC DISCHARGE (ESD) DAMAGE TO THE COMPONENTS:

STAY ON A CONDUCTIVE SURFACE THAT IS ELECTRICALLY GROUNDED.
USE A CONDUCTIVE WRIST-STRAP THAT IS ELECTRICALLY GROUNDED. (CONNECTED TO A BONDING-POINT NEAR THE WORK AREA).
BEFORE YOU USE THE TOOLS, MOMENTARILY HOLD THEM AGAINST AN ELECTRICAL GROUND TO RELEASE STATIC ELECTRICITY.

CAUTION: BEFORE YOU REMOVE OR INSTALL THE REMOVABLE SIM MODULE, MAKE SURE THAT THE WGL DAR IS DE-ENERGIZED. IF YOU DO NOT OBEY THIS INSTRUCTION, DAMAGE TO THE EQUIPMENT CAN OCCUR.

CAUTION: INSTALL THE SIM CARDS VERY CAREFULLY AND MAKE SURE THAT YOU DO NOT CAUSE DAMAGE TO THEIR METAL CONTACTS. THIS WILL HELP TO PREVENT DAMAGE TO OTHER COMPONENTS.

ZONE: 121
FIN: 2TV ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
121	AVIONICS COMPARTMENT
824

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-36-00-740-017-A	Test of the Wireless Ground Link-Digital AIDS Recorder (WGL-DAR)
TASK 52-41-00-010-002-A	Open the Avionics Compartment Doors for Access
TASK 52-41-00-410-002-A	Close the Avionics Compartment Doors after Access
TASK 31-36-00-00-02	AIDS INTERCONNECTION (DMU, DAR) - DESCRIPTION AND OPERATION
Removable SIM Module (RSM) and the SIM Module I/O Cards (SMIO) of the WGL-DAR ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 31-36-00-861-086-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 31-36-00-010-093-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below access door 824.
(2) Open access door 824 (Ref. AMM TASK 52-41-00-010-002).
(3) For the location of the WGL-DAR, refer to paragraph Component Location (Ref. AMM D/O 31-36-00-00).

Subtask 31-36-00-865-166-A ** ON A/C NOT FOR ALL

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	RCDR/ACCLRM	9TU	K18
121VU	AIDS & RCDR/FDIMU	5TV	K15

4. Procedure
Subtask 31-36-00-420-059-A ** ON A/C NOT FOR ALL

A. Installation of the Removable SIM Module (RSM)

Removable SIM Module (RSM) and the SIM Module I/O Cards (SMIO) of the WGL-DAR ** ON A/C NOT FOR ALL

(1) If removed, install the new SIM cards (2).

NOTE: If the SIM cards (2) are replaced, a new OPC (configuration) file must be installed. Contact the vendor customer services for more information. This will help to prevent malfunction of the equipment.

NOTE: It is recommended to record the correct position of the SIM cards (2). You must install the new SIM cards (2) in same position as before removal.

(2) Put the shield (4) in position.
(3) Install and secure the screws (3).
(4) Make sure that the arrow of the RSM (1) points up.
(5) Hold tightly the handle of the RSM (1). Push the RSM (1) into the slot.
(6) Move down the top clip and move up the bottom clip to safety the RSM (1).
(7) Turn the thumbscrew clockwise by hand to safety the access door.

Subtask 31-36-00-865-167-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	RCDR/ACCLRM	9TU	K18
121VU	AIDS & RCDR/FDIMU	5TV	K15

Subtask 31-36-00-710-135-A ** ON A/C NOT FOR ALL

C. Test
(1) Do the WGL-DAR self-test (Ref. AMM TASK 31-36-00-740-017).

5. Close-up
Subtask 31-36-00-410-093-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close access door 824 (Ref. AMM TASK 52-41-00-410-002).
(3) Remove the access platform(s).

Subtask 31-36-00-862-088-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration
(1) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 08:36:18 UTC