Repair of the Vacuum-Cleaner Outlet Door

TASK 25-20-00-340-004-A
Repair of the Vacuum-Cleaner Outlet Door

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05EML8)	Epoxy Adhesive-- - Legacy 2
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -
No specific	Abrasive paper, 180 grade
No specific	Abrasive paper, 240 grade

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 25-23-45-000-002-A	Removal of the Door Frame Linings from the Right Forward Passenger/Crew Door
TASK 25-23-45-000-003-A	Removal of the Door Frame Linings from the Left Aft Passenger/Crew Door
TASK 25-23-45-000-004-A	Removal of the Door Frame Linings from the Right Aft Passenger/Crew Door
TASK 25-23-45-000-005-A	Removal of the Door Frame Linings from the Left Forward Passenger/Crew Door
TASK 25-23-45-400-005-A	Installation of the Door Frame Linings on the Right Aft Passenger/Crew Door
TASK 25-23-45-400-006-A	Installation of the Door Frame Linings on the Left Forward Passenger/Crew Door
TASK 25-23-45-400-007-A	Installation of the Door Frame Linings on the Right Forward Passenger/Crew Door
TASK 25-23-45-400-008-A	Installation of the Door Frame Linings on the Left Aft Passenger/Crew Door

3. Job Set-up
Subtask 25-20-00-860-052-A

A. Get Access
(1) Remove the damaged door frame lining(s):

4. Procedure
Subtask 25-20-00-340-058-A

A. Repair of the Vacuum-Cleaner Outlet Door
(1) Make the bonding areas on the doorframe lining and on the flap rough (only make the resin layer rough, not the fabric):
(a) Make the bonding areas rough with Abrasive paper, 240 grade.
(b) Make the bonding areas rough with Abrasive paper, 180 grade.
(2) Clean the bonding areas with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Bond the support to the flap with Epoxy Adhesive-- - Legacy 2 (Material No.05EML8) .

NOTE: For this repair only the following materials are recommended:

ARALDITE AW 134 with Hardener HV 997
ARALDITE AW 134 with Hardener HY 994

(4) Let the adhesive cure. Obey the manufacturer's instructions.
(5) Bond the support to the door frame lining with Epoxy Adhesive-- - Legacy 2 (Material No.05EML8) .

NOTE: For this repair only the following materials are recommended:

ARALDITE AW 134 with Hardener HV 997
ARALDITE AW 134 with Hardener HY 994

(6) Let the adhesive cure. Obey the manufacturer's instructions.

5. Close-up
Subtask 25-20-00-860-053-A

A. Close Access
(1) Install the door frame lining(s):

[Rev.10 from 2021] 2026.03.31 23:30:01 UTC