Installation of the Low Oil Pressure (LOP) Switch [PW11]

TASK 79-33-25-400-801-A
Installation of the Low Oil Pressure (LOP) Switch

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY TO PREVENT ENGINE DAMAGE.

ZONE: 400
FIN: 4080KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	PLIERS - JAWED, SOFT
No specific	Torque wrench: range to between 30 and 26 lbf.in (0.34 and 0.29 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.P03-001)	lubricant, aircraft turbine engine

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
3	PACKING	EIPC 79-33-25-01-090

E. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-720-811-A	Test No. 3A - Idle Power Test
TASK 71-00-00-860-832-A	Procedure to Prevent Engine Motoring and to Stop the Electrical Supply to the EEC
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-802-A	Closing of the Fan Cowl Doors
TASK 73-25-34-400-802-A	Installation of the Engine Interface Unit (EIU)
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-805-A	Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
TASK 78-36-00-410-802-A	Closing of the Thrust Reverser Cowl-Doors
Low Oil Pressure (LOP) Switch

3. Job Set-up
Subtask 79-33-25-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Make sure that you did the procedure to prevent engine motoring and to stop the electrical supply to the Electronic Engine Control (EEC)
(Ref. AMM TASK 71-00-00-860-832).

Subtask 79-33-25-865-052-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ANTI ICE/PROBES/AOA/1	4DA1	D04
49VU	ANTI ICE/PROBES/PITOT/1	3DA1	D02
122VU	ANTI ICE/PROBES/2/TAT	1DA2	Y15
122VU	ANTI ICE/PROBES/2/PITOT	3DA2	Y14
122VU	ANTI ICE/PROBES/2/AOA	4DA2	Y13
122VU	ANTI ICE/PROBES/2/STATIC	5DA2	Y11
122VU	ANTI ICE/PROBES/3/PITOT	3DA3	Z16
122VU	ANTI ICE/PROBES/3/AOA	4DA3	Z15
122VU	ANTI ICE/PROBES/3/STATIC	5DA3	Z14
122VU	ANTI ICE/PROBES/1/STATIC	5DA1	Z13
122VU	ANTI ICE/PROBES/1/TAT	1DA1	Z12
FOR FIN: 1KS1 (EIU1)
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R41
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R40
** ON A/C NOT FOR ALL
FOR FIN: 1KS2 (EIU2)
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG2/FADEC B/AND EIU2	4KS2	Q40
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG2/FADEC B/AND EIU2	4KS2	R41

Subtask 79-33-25-865-053-A ** ON A/C NOT FOR ALL

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ANTI ICE/PROBES/PHC/1	2DA1	D03
122VU	ANTI ICE/WHC/2	5DG2	W13
122VU	ANTI ICE/WHC/1	5DG1	X13
122VU	ANTI ICE/PROBES/PHC/3	2DA3	Y16
122VU	ANTI ICE/PROBES/PHC/2	2DA2	Y12

Subtask 79-33-25-010-052-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR

Subtask 79-33-25-040-051-A ** ON A/C NOT FOR ALL

E. Deactivation of the Thrust Reverser for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Make sure that you did the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 79-33-25-010-053-A ** ON A/C NOT FOR ALL

F. Get Access
(1) Make sure that the left thrust-reverser cowl-doors are open (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL

4. Procedure
Subtask 79-33-25-420-050-A ** ON A/C NOT FOR ALL

A. Installation of the LOP Switch

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

(1) Make sure that you remove the COVER - PROTECTION as necessary to prevent damage to the engine.
(2) Install the switch (1) as follows:
(a) Put a small amount of P03-001lubricant, aircraft turbine engine on the new EIPC 79-33-25-01-090 PACKING (3).
(b) Install the new EIPC 79-33-25-01-090 PACKING (3) on the switch (1).
(c) Install the switch (1) on the oil manifold with the two bolts (2).
(d) TORQUE the two bolts (2) to between 30 and 26 lbf.in (0.34 and 0.29 m.daN )

.
(3) Connect wiring harness connector P70 to switch receptacle J70 as follows:
(a) Examine, align and engage the connector.
(b) Push lightly inward on the connector while you tighten the coupling ring.
(c) Use the PLIERS - JAWED, SOFT to tighten the connector against the receptacle.
(d) While you tighten, push the connector in and from side to side.
(e) Make sure that you can feel the ratchet feature.
(f) Tighten the connector until the PLIERS - JAWED, SOFT slip on the connector ring.
(4) Examine the assembly for foreign objects, damage and correct assembly.

5. Close-up
Subtask 79-33-25-860-050-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the left thrust-reverser cowl-doors (Ref. AMM TASK 78-36-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL

Subtask 79-33-25-865-054-A ** ON A/C NOT FOR ALL

WARNING: CLOSE THE CIRCUIT BREAKERS RELATED TO THE PHC AND WHC AND CIRCUIT BREAKER 4KS1(2) BEFORE YOU CLOSE THE PROBE HEATER AND WINDOW HEATER CIRCUIT-BREAKERS: IF YOU DO NOT OBEY THIS SEQUENCE:

THE PROBES WILL BECOME TOO HOT.
THIS CAN CAUSE INJURY TO MAINTENANCE PERSONNEL AND/OR DAMAGE TO EQUIPMENT.

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ANTI ICE/PROBES/PHC/1	2DA1	D03
122VU	ANTI ICE/WHC/2	5DG2	W13
122VU	ANTI ICE/WHC/1	5DG1	X13
122VU	ANTI ICE/PROBES/PHC/3	2DA3	Y16
122VU	ANTI ICE/PROBES/PHC/2	2DA2	Y12

Subtask 79-33-25-865-055-A ** ON A/C NOT FOR ALL

C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ANTI ICE/PROBES/AOA/1	4DA1	D04
49VU	ANTI ICE/PROBES/PITOT/1	3DA1	D02
122VU	ANTI ICE/PROBES/2/TAT	1DA2	Y15
122VU	ANTI ICE/PROBES/2/PITOT	3DA2	Y14
122VU	ANTI ICE/PROBES/2/AOA	4DA2	Y13
122VU	ANTI ICE/PROBES/2/STATIC	5DA2	Y11
122VU	ANTI ICE/PROBES/3/PITOT	3DA3	Z16
122VU	ANTI ICE/PROBES/3/AOA	4DA3	Z15
122VU	ANTI ICE/PROBES/3/STATIC	5DA3	Z14
122VU	ANTI ICE/PROBES/1/STATIC	5DA1	Z13
122VU	ANTI ICE/PROBES/1/TAT	1DA1	Z12
FOR FIN: 1KS1 (EIU1)
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R41
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R40
** ON A/C NOT FOR ALL
FOR FIN: 1KS2 (EIU2)
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG2/FADEC B/AND EIU2	4KS2	Q40
** ON A/C NOT FOR ALL
121VU	ENGINE/ENG2/FADEC B/AND EIU2	4KS2	R41

Subtask 79-33-25-410-050-A ** ON A/C NOT FOR ALL

D. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR
(2) Remove the WARNING NOTICE(S).

Subtask 79-33-25-440-050-A ** ON A/C NOT FOR ALL

E. Do the reactivation of the thrust reverser system after maintenance (Ref. AMM TASK 78-30-00-440-805).
(1) Make sure that all the circuit breakers shown in the paragraph Procedure of the engine interface unit installation are closed. If they are not, close them in the recommended sequence
(Ref. AMM TASK 73-25-34-400-802)

Subtask 79-33-25-720-050-A ** ON A/C NOT FOR ALL

F. Test
(1) Do the test no. 3: idle power test (Ref. AMM TASK 71-00-00-720-811).

[Rev.10 from 2021] 2026.04.01 03:42:22 UTC