Operational Test of the Door Warning System

TASK 52-71-00-710-001-A
Operational Test of the Door Warning System

ZONE: 210

1. Reason for the Job
Refer to the MPD TASK: 527100-01
OPERATIONAL CHECK OF DOOR WARNING SYSTEM

NOTE: This task is only applicable to these doors without mechanical and/or permanent blockage from the inner/outer part of the aircraft:

The passenger/crew doors
The emergency exit doors
The avionics compartment doors.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	WARNING NOTICE(S)
No specific	1	WRENCH - SPANNER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure
TASK 52-10-00-010-001-A	Opening of the Passenger/Crew Door
TASK 52-10-00-410-001-A	Closing of the Passenger/Crew Door
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
TASK 52-22-00-010-002-A	Opening of the Emergency Exit Doors from the Outside
TASK 52-22-00-410-002-A	Closing of the Emergency Exit Doors from the Outside
TASK 52-22-00-860-003-A	Special Precaution before Maintenance on the Door Damper and Emergency Operation Cylinder
TASK 52-22-00-860-004-A	Special Precaution after Maintenance on the Door Damper and Emergency Operation Cylinder
TASK 52-30-00-860-001-A	Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
TASK 52-30-00-860-002-A	Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
Disarming of the Emergency Exit Doors ** ON A/C NOT FOR ALL
Disarming of the Emergency Exit Doors ** ON A/C NOT FOR ALL
"DOOR/OXY" Page ** ON A/C NOT FOR ALL
"DOOR/OXY" Page ** ON A/C NOT FOR ALL
"DOOR/OXY" Page ** ON A/C NOT FOR ALL
"DOOR/OXY" Page ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 52-71-00-861-050-A

A. Energize the ground service network (Ref. AMM TASK 24-42-00-861-001).

Subtask 52-71-00-865-051-A

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	LIGHTING/EMER LT/CABIN	2WL	H06
49VU	LIGHTING/EMER LT/CABIN	1WL	H05
** ON A/C NOT FOR ALL
49VU	LIGHTING/EMER LT/CABIN	2WL	H04
49VU	LIGHTING/EMER LT/CABIN	1WL	H03
** ON A/C ALL
122VU	LIGHTING/CABIN/EMER/LT	3WL	V07

Subtask 52-71-00-869-050-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the passenger/crew door at zone 831, 832, 841 or 842.
(2) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start the work on the door (Ref. AMM TASK 52-10-00-860-001).
(4) Disarm the escape slides of the four emergency exits doors (3):

Disarming of the Emergency Exit Doors ** ON A/C NOT FOR ALL

(a) Open and remove the flaps (2) from the four emergency exits doors (3).

NOTE: The two SLIDE ARMED indicator lights (4) come on.

(b) On the four emergency exits doors (3), use the applicable wrench to turn the head of the latch pin (1) a quarter turn counterclockwise to retract the latch pin (1).

NOTE: The two SLIDE ARMED indicator lights (4) go off.

Subtask 52-71-00-869-050-B ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the passenger/crew door at zone 831, 841, 832 or 842.
(2) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start the work on the door (Ref. AMM TASK 52-10-00-860-001).
(4) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in front of the applicable emergency exit door at zone 833, 834, 843 or 844.
(5) Open the applicable emergency exit door (Ref. AMM TASK 52-22-00-010-002).
(6) Obey the safety precautions before you start the work on the emergency exit door (Ref. AMM TASK 52-22-00-860-003).
(7) Close the doors from the inside.

Subtask 52-71-00-869-050-C ** ON A/C NOT FOR ALL

Disarming of the Emergency Exit Doors ** ON A/C NOT FOR ALL

(a) Open and remove the flaps (2) from the two emergency exit doors (3).

NOTE: The two SLIDE ARMED indicator lights (4) come on.

(b) On the two emergency exit doors (3), use the applicable wrench to turn the head of the latch pin (1) a quarter turn counterclockwise to retract the latch pin (1).

NOTE: The two SLIDE ARMED indicator lights (4) go off.

Subtask 52-71-00-869-050-G ** ON A/C NOT FOR ALL

C. Get Access
(1) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the applicable passenger/crew door at zone 831 or 841 or 832 or 842.
(2) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start the work on the door (Ref. AMM TASK 52-10-00-860-001).
(4) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the applicable emergency exit door at zone 835 or 845.
(5) Open the applicable emergency exit door (Ref. AMM TASK 52-22-00-010-002).
(6) Obey the safety precautions before you start the work on the emergency exit door (Ref. AMM TASK 52-22-00-860-003).
(7) Close the doors from the inside.

Subtask 52-71-00-860-060-A ** ON A/C NOT FOR ALL

D. Aircraft Maintenance Configuration

WARNING: MAKE SURE THAT THE SLIDING WINDOW IS OPEN. THIS PREVENTS PRESSURIZATION OF THE AIRCRAFT WHEN THE AVIONICS VENTILATION SYSTEM OPERATES AND ALL THE DOORS ARE CLOSED.

(1) Make sure that all the doors are closed.
(2) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
(3) On the ECAM control panel, push the DOOR key. On the lower ECAM Display Unit (DU), the "DOOR/OXY" page comes into view.
(4) Put the WARNING NOTICE(S) in position on the applicable door to tell persons not to open the door during the test procedure.
(5) Make sure that these doors are closed and locked:

The four avionics compartment access-doors
The forward and aft cargo-compartment doors (Ref. AMM TASK 52-30-00-860-002)
The four passenger/crew doors
The bulk cargo-compartment door (if installed)
The entrance stairs door (if installed)
The emergency exit doors.

Subtask 52-71-00-860-060-C ** ON A/C NOT FOR ALL

D. Aircraft Maintenance Configuration

WARNING: MAKE SURE THAT THE SLIDING WINDOW IS OPEN. THIS PREVENTS PRESSURIZATION OF THE AIRCRAFT WHEN THE AVIONICS VENTILATION SYSTEM OPERATES AND ALL THE DOORS ARE CLOSED.

(1) Make sure that all the doors are closed.
(2) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
(3) On the ECAM control panel, push the DOOR key. On the lower ECAM DU, the "DOOR/OXY" page comes into view.
(4) Put the WARNING NOTICE(S) in position on the applicable door to tell persons not to open the door during the test procedure.
(5) Make sure that these doors are closed and locked:

The four avionics compartment access-doors
The forward and aft cargo-compartment doors (Ref. AMM TASK 52-30-00-860-002)
The four passenger/crew doors
The bulk cargo-compartment door (if installed)
The entrance stairs door (if installed)
The two emergency exit doors
The four overwing emergency-exit doors.

Subtask 52-71-00-865-050-A

E. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
49VU	L/G/LGCIU/SYS1/NORM	1GA	C09
49VU	SDAC/1/SPLY	3WV	F04
49VU	FWS/FWC1/SPLY	3WW	F01
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05
121VU	EIS/SDAC1 AND 2/DOOR/DET/AVNCS	46WV	P02
121VU	HYDRAULIC/LGCIU/SYS2	2GA	Q35
121VU	HYDRAULIC/LGCIU/SYS1/GRND SPLY	52GA	Q34
121VU	EIS/FWC2/SPLY	2WW	Q07
121VU	EIS/SDAC/2/SPLY	2WV	Q06

4. Procedure
Subtask 52-71-00-710-050-B ** ON A/C NOT FOR ALL

A. Test of the Door Warning System

"DOOR/OXY" Page ** ON A/C NOT FOR ALL

(Ref. AMM TASK 52-30-00-860-001) (Ref. AMM TASK 52-30-00-860-002)

WARNING: INSTALL A SAFETY BARRIER WHEN YOU OPEN A DOOR IF THE ACCESS PLATFORM IS NOT USED.

(1) Do the test that follows:

ACTION	RESULT
1.On the ECAM control panel, push the DOOR key.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors, the two cargo compartment doors and the bulk cargo-compartment door become green. The symbols of the four passenger/crew doors and the four emergency exit doors become green. The "AVIONIC", "CARGO", "BULK", "CABIN" and "EMER EXIT" messages go out of view.
2.On circuit breaker panel 121VU: Open circuit breaker 2WV. Open circuit breakers 15WN and 2WW.	No change.
3.On circuit breaker panel 121VU: Close circuit breakers 2WV and 2WW. On circuit breaker panel 49VU: Open circuit breakers 3WV and 3WW.	No change.
4.Open the four avionics compartment doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors and the "AVIONIC" message comes into view in amber.
5.Open the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-001).	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the two cargo compartment doors and the "CARGO" message come into view in amber.
6.Open the bulk cargo-compartment door.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the bulk cargo-compartment door and the "BULK" message come into view in amber.
7.Open the four passenger/crew doors and the four flaps that give access to the control handles of the emergency exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors and the four emergency exit doors become amber. The "CABIN" and "EMER EXIT" messages come into view in amber.
8.On circuit breaker panel 121VU: Close circuit breaker 15WN. Open circuit breaker 13WN.	No change.
9.Close the four passenger/crew doors and the four flaps that give access to the control handles of the emergency exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors and the four emergency exit doors become green. The "CABIN" and "EMER EXIT" messages go out of view.
10.Close the four avionics compartment doors, the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-002) and the bulk cargo-compartment door.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors, the two cargo compartment doors and the bulk cargo-compartment door become green. The "AVIONIC", "CARGO" and "BULK" messages go out of view.
11.On circuit breaker panel 121VU: Close circuit breaker 13WN.
12.On circuit breaker panel 49VU: Close circuit breakers 3WW and 3WV.

Subtask 52-71-00-710-050-G ** ON A/C NOT FOR ALL

A. Test of the Door Warning System

"DOOR/OXY" Page ** ON A/C NOT FOR ALL

(Ref. AMM TASK 52-30-00-860-001) (Ref. AMM TASK 52-30-00-860-002)

WARNING: INSTALL A SAFETY BARRIER WHEN YOU OPEN A DOOR IF THE ACCESS PLATFORM IS NOT USED.

(1) Do the test that follows:

ACTION	RESULT
1.On the ECAM control panel, push the DOOR key:	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors and the two cargo compartment doors become green. The symbols of the four passenger/crew doors and the two emergency exit doors become green. The "AVIONIC", "CARGO", "CABIN" and "EMER EXIT" messages go out of view.
2.On circuit breaker panel 121VU: Open circuit breaker 2WV. Open circuit breakers 15WN and 2WW.	No change.
3.On circuit breaker panel 121VU: Close circuit breakers 2WV and 2WW. On circuit breaker panel 49VU: Open circuit breakers 3WV and 3WW.	No change.
4.Open the four avionics compartment doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors and the "AVIONIC" message come into view in amber.
5.Open the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-001).	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the two cargo compartment doors and the "CARGO" message come into view in amber.
6.Open the four passenger/crew doors and the two flaps that give access to the control handles of the emergency exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors and the two emergency exit doors become amber. The "CABIN" and "EMER EXIT" messages come into view in amber.
7.On circuit breaker panel 121VU: Close circuit breaker 15WN. Open circuit breaker 13WN.	No change.
8.Close the four passenger/crew doors and the two flaps that give access to the control handles of the emergency exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors and the two emergency exit doors become green. The "CABIN" and "EMER EXIT" messages go out of view.
9.Close the four avionics compartment doors and the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-002).	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors and the two cargo compartment doors become green. The "AVIONIC" and "CARGO" messages go out of view.
10.On circuit breaker panel 121VU: Close circuit breaker 13WN.
11.On circuit breaker panel 49VU: Close circuit breakers 3WW and 3WV.

Subtask 52-71-00-710-050-I ** ON A/C NOT FOR ALL

A. Test of the Door Warning System

"DOOR/OXY" Page ** ON A/C NOT FOR ALL

(Ref. AMM TASK 52-30-00-860-001) (Ref. AMM TASK 52-30-00-860-002)

WARNING: INSTALL A SAFETY BARRIER WHEN YOU OPEN A DOOR IF THE ACCESS PLATFORM IS NOT USED.

(1) Do the test that follows:

ACTION	RESULT
1.On the ECAM control panel, push the DOOR key.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors, the two cargo compartment doors and the bulk cargo-compartment door become green. The symbols of the four passenger/crew doors and the four emergency exit doors become green. The "AVIONIC", "CARGO", "BULK", "CABIN" and "EMER EXIT" messages go out of view.
2.On circuit breaker panel 121VU: Open circuit breaker 2WV. Open circuit breakers 15WN and 2WW.	No change.
3.On circuit breaker panel 121VU: Close circuit breakers 2WV and 2WW. On circuit breaker panel 49VU: Open circuit breakers 3WV and 3WW.	No change.
4.Open the four avionics compartment doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors and the "AVIONIC" message come into view in amber.
5.Open the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-001).	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the two cargo compartment doors and the "CARGO" message come into view in amber.
6.Open the bulk cargo-compartment door.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the bulk cargo-compartment door and the "BULK" message come into view in amber.
7.Open the four passenger/crew doors and the four emergency exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors and the four emergency exit doors become amber. The "CABIN" and "EMER EXIT" messages come into view in amber.
8.On circuit breaker panel 121VU: Close circuit breaker 15WN. Open circuit breaker 13WN.	No change.
9.Close the four passenger/crew doors and the four emergency exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors and the four emergency exit doors become green. The "CABIN" and "EMER EXIT" messages go out of view.
10.Close the four avionics compartment doors, the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-002) and the bulk cargo-compartment door.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment doors, the two cargo compartment doors and the bulk cargo-compartment door become green. The "AVIONIC", "CARGO" and "BULK" messages go out of view.
11.On circuit breaker panel 121VU: Close circuit breaker 13WN.
12.On circuit breaker panel 49VU: Close circuit breakers 3WW and 3WV.

Subtask 52-71-00-710-050-N ** ON A/C NOT FOR ALL

A. Test of the Door Warning System

"DOOR/OXY" Page ** ON A/C NOT FOR ALL

(Ref. AMM TASK 52-30-00-860-001) (Ref. AMM TASK 52-30-00-860-002)

WARNING: INSTALL A SAFETY BARRIER WHEN YOU OPEN A DOOR IF THE ACCESS PLATFORM IS NOT USED.

(1) Do the test that follows:

ACTION	RESULT
1.On the ECAM control panel, push the DOOR key.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment access-doors, the two cargo compartment doors and the bulk cargo-compartment door become green. The symbols of the four passenger/crew doors, the applicable emergency exit doors and the applicable overwing emergency-exit doors become green. The "AVIONIC", "CARGO", "BULK","CABIN", "EMER EXIT" and "OVERWING" messages go out of view.
2.On circuit breaker panel 121VU: Open circuit breaker 2WV. Open circuit breakers 15WN and 2WW.	No change.
3.On circuit breaker panel 121VU: Close circuit breakers 2WV and 2WW.	No change.
4.On circuit breaker panel 49VU: Open circuit breakers 3WV and 3WW.	No change.
5.Open the four avionics compartment access-doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment access-doors and the "AVIONIC" message come into view in amber.
6.Open the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-001).	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the two cargo compartment doors and the "CARGO" message come into view in amber.
7.Open the bulk cargo-compartment door.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the bulk cargo-compartment door and the "BULK" message come into view in amber.
8.Open the four passenger/crew doors, the applicable emergency exit doors and the applicable overwing emergency-exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors, the applicable emergency exit doors and the applicable overwing emergency-exit doors become amber. The "CABIN", "EMER EXIT" and "OVERWING" messages come into view in amber.
9.On circuit breaker panel 121VU: Close circuit breaker 15WN. Open circuit breaker 13WN.	No change.
10.Close the four passenger/crew doors, the applicable emergency exit doors and the applicable overwing emergency-exit doors.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four passenger/crew doors, the applicable emergency exit doors and the applicable overwing emergency-exit doors become green. The "CABIN", "EMER EXIT" and "OVERWING" messages go out of view.
11.Close the four avionics compartment access-doors, the two cargo compartment doors (Ref. AMM TASK 52-30-00-860-002) and the bulk cargo-compartment door.	On the lower ECAM DU, on the "DOOR/OXY" page: The symbols of the four avionics compartment access-doors, the two cargo compartment doors and the bulk cargo-compartment door become green. The "AVIONIC", "CARGO" and "BULK" messages go out of view.
12.On circuit breaker panel 121VU: Close circuit breaker 13WN.
13.On circuit breaker panel 49VU: Close circuit breakers 3WW and 3WV.

5. Close-up
Subtask 52-71-00-860-061-A

A. Put the aircraft back to its initial configuration.
(1) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).

Subtask 52-71-00-865-081-A

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	LIGHTING/EMER LT/CABIN	2WL	H06
49VU	LIGHTING/EMER LT/CABIN	1WL	H05
** ON A/C NOT FOR ALL
49VU	LIGHTING/EMER LT/CABIN	2WL	H04
49VU	LIGHTING/EMER LT/CABIN	1WL	H03
** ON A/C ALL
122VU	LIGHTING/CABIN/EMER/LT	3WL	V07

Subtask 52-71-00-410-071-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Arm the escape slides of the emergency exits (3):

Disarming of the Emergency Exit Doors ** ON A/C NOT FOR ALL

(a) Open and remove the cover flaps (2) from the emergency exit doors (3).
(b) Use the WRENCH - SPANNER to turn the head of the latch pin (1) a quarter turn clockwise to extend the latch pin (1).
(c) Make sure that the SLIDE ARMED indicator lights (4) come on.
(d) Install and close the cover flaps (2) on the emergency exit doors (3).
(e) Make sure that the SLIDE ARMED indicator lights (4) go off.
(2) Obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(4) Close the applicable passenger/crew door (Ref. AMM TASK 52-10-00-410-001).
(5) Remove the access platform(s).
(6) Make sure that the work area is clean and clear of tools and other items.

Subtask 52-71-00-410-071-B ** ON A/C NOT FOR ALL

C. Close Access
(1) Obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3) Close the applicable passenger/crew door (Ref. AMM TASK 52-10-00-410-001).
(4) Obey the special precautions after the work on the emergency exit door (Ref. AMM TASK 52-22-00-860-004).
(5) Close the applicable emergency exit door (Ref. AMM TASK 52-22-00-410-002).
(6) Remove the access platform(s).
(7) Make sure that the work area is clean and clear of tools and other items.

Subtask 52-71-00-862-050-A

D. De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 12:44:09 UTC