DOC AIRBUS | AMM A320FClosing of the Emergency Exit Doors from the Outside
TASK 52-22-00-410-002-A
Closing of the Emergency Exit Doors from the Outside
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 52-22-00-860-062-A ** ON A/C NOT FOR ALL
Subtask 52-22-00-010-056-B ** ON A/C NOT FOR ALL
Subtask 52-22-00-010-058-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 03:55:05 UTC
Closing of the Emergency Exit Doors from the Outside
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE |
| 98A52107632000 | 1 | PIN - SAFETY SLIDE |
| 98D52207551000 | 1 | PIN-SAFETY - SLIDE RELEASE LEVER |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 52-10-00-010-001-A | Opening of the Passenger/Crew Door |
| TASK 52-10-00-410-001-A | Closing of the Passenger/Crew Door |
| TASK 52-22-00-860-004-A | Special Precaution after Maintenance on the Door Damper and Emergency Operation Cylinder |
Subtask 52-22-00-860-062-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
(2) Make sure that the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE is in position below the opened door.
4. Procedure(1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
(2) Make sure that the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE is in position below the opened door.
Subtask 52-22-00-010-056-B ** ON A/C NOT FOR ALL
A. Closing of the Door
Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL
Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL
Normal Operation from the Outer Side ** ON A/C NOT FOR ALL
Normal Operation from the Outer Side ** ON A/C NOT FOR ALL
(2) Push the release button so that the door stay mechanism releases the door.
(3) Pull the door rearward until you get access to the door damper and emergency operation cylinder.
(4) Do the special precaution after maintenance on the door damper and emergency operation cylinder (Ref. AMM TASK 52-22-00-860-004).
(5) Remove the 98D52207551000 PIN-SAFETY - SLIDE RELEASE LEVER from the slide release lever and the frame fitting.
(6) Move the door rearward and inboard until it is in the correct position at the opening.
(7) Push down the outboard handle so that the door lowers into the opening.
Subtask 52-22-00-860-063-A ** ON A/C NOT FOR ALL Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL Normal Operation from the Outer Side ** ON A/C NOT FOR ALL Normal Operation from the Outer Side ** ON A/C NOT FOR ALL WARNING:
BEFORE YOU CONNECT THE INFLATION RESERVOIR TO THE SYSTEM, MAKE SURE THAT THE RELEASE LEVER IS IN THE DISARMED POSITION. IF IT IS NOT, THE INFLATION RESERVOIR WILL OPERATE IMMEDIATELY AND THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1) Make sure that the slide release lever is in the DISARMED position. (2) Push the release button so that the door stay mechanism releases the door.
(3) Pull the door rearward until you get access to the door damper and emergency operation cylinder.
(4) Do the special precaution after maintenance on the door damper and emergency operation cylinder (Ref. AMM TASK 52-22-00-860-004).
(5) Remove the 98D52207551000 PIN-SAFETY - SLIDE RELEASE LEVER from the slide release lever and the frame fitting.
(6) Move the door rearward and inboard until it is in the correct position at the opening.
(7) Push down the outboard handle so that the door lowers into the opening.
B. Final Procedure
Normal Operation from the Passenger Compartment ** ON A/C NOT FOR ALL
Normal Operation from the Passenger Compartment ** ON A/C NOT FOR ALL
Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL
Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL
(1) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(2) Arm the escape slide-release mechanism of the door as follows:
(a) Remove the 98A52107632000 PIN - SAFETY SLIDE from the slide control handle.
(b) Push down the slide control handle to the ARMED position.
(3) Remove the lock pin from the inflation reservoir as follows:
(a) Remove the lock pin from the operation valve of the inflation reservoir.
(b) Put the lock pin in the stowage pocket of the inflation reservoir.
(c) Make sure that the work area is clean and clear of tools and other items.
(d) Install the rear inside fairing in the applicable overhead stowage compartment.
(e) Close the access door of the applicable overhead stowage compartment.
(4) Make sure that the handle cover is over the inboard handle.
Subtask 52-22-00-860-063-B ** ON A/C NOT FOR ALL Normal Operation from the Passenger Compartment ** ON A/C NOT FOR ALL Normal Operation from the Passenger Compartment ** ON A/C NOT FOR ALL Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL Lock Pin in the Inflation Reservoir ** ON A/C NOT FOR ALL (2) Arm the escape slide-release mechanism of the door as follows:
(a) Remove the 98A52107632000 PIN - SAFETY SLIDE from the slide control handle.
(b) Push down the slide control handle to the ARMED position.
(3) Remove the lock pin from the inflation reservoir as follows:
(a) Remove the lock pin from the operation valve of the inflation reservoir.
(b) Put the lock pin in the stowage pocket of the inflation reservoir.
(c) Make sure that the work area is clean and clear of tools and other items.
(d) Install the rear inside fairing in the applicable overhead stowage compartment.
(e) Close the access door of the applicable overhead stowage compartment.
(4) Make sure that the handle cover is over the inboard handle.
B. Final Procedure
(1) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(2) Arm the escape slide-release mechanism of the door as follows:
(a) Remove the 98A52107632000 PIN - SAFETY SLIDE from the slide control handle.
(b) Push down the slide control handle to the ARMED position.
(c) Close the protection cover to prevent the direct access to the slide control handle.
(3) Remove the lock pin from the inflation reservoir as follows:
(a) Remove the lock pin from the operation valve of the inflation reservoir.
(b) Put the lock pin in the stowage pocket of the inflation reservoir.
(c) Make sure that the work area is clean and clear of tools and other items.
(d) Install the rear inside fairing in the applicable overhead stowage compartment.
(e) Close the access door of the applicable overhead stowage compartment.
(4) Make sure that the handle cover is over the inboard handle.
5. Close-up(1) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(2) Arm the escape slide-release mechanism of the door as follows:
(a) Remove the 98A52107632000 PIN - SAFETY SLIDE from the slide control handle.
(b) Push down the slide control handle to the ARMED position.
(c) Close the protection cover to prevent the direct access to the slide control handle.
(3) Remove the lock pin from the inflation reservoir as follows:
(a) Remove the lock pin from the operation valve of the inflation reservoir.
(b) Put the lock pin in the stowage pocket of the inflation reservoir.
(c) Make sure that the work area is clean and clear of tools and other items.
(d) Install the rear inside fairing in the applicable overhead stowage compartment.
(e) Close the access door of the applicable overhead stowage compartment.
(4) Make sure that the handle cover is over the inboard handle.
Subtask 52-22-00-010-058-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Close the applicable passenger/crew door (Ref. AMM TASK 52-10-00-410-001).
(2) Remove the access platform(s).
(1) Close the applicable passenger/crew door (Ref. AMM TASK 52-10-00-410-001).
(2) Remove the access platform(s).