Deactivation of the ATT HDG Selector Switch
TASK 31-68-00-040-004-A
Deactivation of the ATT HDG Selector Switch
MMEL 31-68-02A
ATT HDG SWITCHING SELECTOR ON THE CENTER PEDESTAL (FAA ONLY)
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 31-68-00-860-053-A Subtask 31-68-00-865-051-A
Subtask 31-68-00-710-051-A ** ON A/C NOT FOR ALL
Subtask 31-68-00-860-055-A
[Rev.10 from 2021]
2026.04.01 00:39:00 UTC
Deactivation of the ATT HDG Selector Switch
ZONE: 210
1. Reason for the JobMMEL 31-68-02A
ATT HDG SWITCHING SELECTOR ON THE CENTER PEDESTAL (FAA ONLY)
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 210 | CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 31-60-00-860-001-A | EIS Start Procedure |
| TASK 31-60-00-860-002-A | EIS Stop Procedure |
| TASK 34-10-00-860-005-A | ADIRS Stop Procedure |
Subtask 31-68-00-860-053-A Subtask 31-68-00-865-051-A
B. Make sure that this(these) circuit breaker(s) is(are) closed:
Subtask 31-68-00-860-054-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | EIS/PFD CAPT/SPLY | 11WT1 | E03 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | EIS/RLY/BOX/CAPT | 17WT1 | E08 |
| 49VU | NAV/STBY/ALTM | 16FN | F14 |
| 49VU | NAV/STBY/HORIZON | 5FN | F12 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | NAV/VOR/DME/RMI | 12FN | F13 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | NAV PROBES/ADIRU3/PWR/SWTG | 8FP | F09 |
| 49VU | NAV/ADF/1 | 1RP1 | H14 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | EIS/ECAM/CTL/PNL | 15WT | E12 |
| 49VU | EIS/DMC1/SPLY | 10WT1 | E11 |
| 49VU | EIS/DMC3/STBY/SPLY | 14WT1 | E10 |
| 49VU | EIS/DMC1/SWTG | 21WT1 | E09 |
| ** ON A/C ALL | |||
| 49VU | L/G/LGCIU/SYS1/NORM | 1GA | C09 |
| 49VU | EIS/DMC3/SWTG | 21WT3 | E07 |
| 49VU | EIS/ECAM DU/UPPER/SWTG | 24WT1 | E06 |
| 49VU | EIS/ECAM DU/UPPER/SPLY | 13WT1 | E05 |
| 49VU | EIS/PFD CAPT/SWTG | 22WT1 | E04 |
| 49VU | NAV PROBES/ADIRU 1/AND AOA 1/26VAC | 5FP1 | F07 |
| 49VU | NAV PROBES/ADIRU1/115VAC | 4FP1 | F06 |
| 49VU | NAV/DME/1 | 1SD1 | G14 |
| 49VU | NAV/VOR/1 | 2RS1 | G13 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | NAV/ILS/1 | 1RT1 | G12 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | EIS/PFD/CAPT/SPLY | 11WT1 | E03 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | NAV/STBY/INST | 5FN | F12 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | NAV PROBES/ADF/1 | 1RP1 | F09 |
| 49VU | NAV PROBES/ADIRU3/PWR/SWTG | 8FP | F08 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | EIS/ECAM/CTL/PNL | 15WT | E11 |
| 49VU | EIS/DMC1/SPLY | 10WT1 | E10 |
| 49VU | EIS/DMC3/STBY/SPLY | 14WT1 | E09 |
| 49VU | EIS/DMC1/SWTG | 21WT1 | E08 |
| ** ON A/C ALL | |||
| 105VU | ADIRS/ADIRU1/28VDC | 6FP1 | C02 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | EIS/RLY/BOX/F/O | 17WT2 | R07 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | ADIRS/ADIRU/2PWR/SHED | 10FP | N10 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/TCAS | 4SG | K10 |
| 121VU | EIS/GPWS/115VAC | 3WZ | P07 |
| ** ON A/C ALL | |||
| 121VU | COM NAV/RADAR/1 | 5SQ1 | K13 |
| 121VU | COM NAV/RAD ALTM/2 | 1SA2 | K12 |
| 121VU | COM NAV/RAD ALTM/1 | 1SA1 | K11 |
| 121VU | COM NAV/VOR/2 | 2RS2 | K08 |
| 121VU | COM NAV/DME/2 | 1SD2 | K06 |
| 121VU | ADIRS/ADIRU/3PWR/SWTG | 9FP | N09 |
| 121VU | ADIRS/ADIRU/2/26VAC AND AOA | 5FP2 | N08 |
| 121VU | ADIRS/ADIRU/3/26VAC AND AOA | 5FP3 | N07 |
| 121VU | ADIRS/ADIRU/2/115VAC | 4FP2 | N06 |
| 121VU | ADIRS/ADIRU/3/115VAC | 4FP3 | N05 |
| 121VU | ADIRS/ADIRU/2/28VDC | 6FP2 | N04 |
| 121VU | ADIRS/ADIRU/3/28VDC | 6FP3 | N03 |
| 121VU | EIS/GPWS/28VDC | 2WZ | P06 |
| 121VU | HYDRAULIC/LGCIU/SYS2 | 2GA | Q35 |
| 121VU | HYDRAULIC/LGCIU/SYS1/GRND SPLY | 52GA | Q34 |
| 121VU | EIS/DMC3/SPLY | 10WT3 | Q09 |
| 121VU | EIS/DMC2/SPLY | 10WT2 | Q08 |
| 121VU | EIS/ECAM DU/LOWER/SPLY | 13WT2 | R11 |
| 121VU | EIS/ECAM DU/LOWER/SWTG | 24WT2 | R10 |
| 121VU | EIS/DMC2/SWTG | 21WT2 | R08 |
| 121VU | EIS/PFD/F/O/SWTG | 22WT2 | R05 |
| 121VU | EIS/PFD/F/O | 11WT2 | R03 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/ILS/2 | 1RT2 | K09 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | COM NAV/ADF/2 | 1RP2 | K02 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | ADIRS/2PWR/SHED &/AOA2 MON | 10FP | N10 |
| ** ON A/C ALL | |||
| 122VU | ELEC/AC/BUS1/CTL | 17XN1 | V25 |
C. Aircraft Maintenance Configuration
(1) Do the EIS start procedure (PFDs and NDs only) (Ref. AMM TASK 31-60-00-860-001).
(2) On the overhead panel:
On the ADIRS CDU, on the panel 20VU, make sure that the OFF/NAV/ATT selector switches for ADIRU1 and ADIRU2 are at NAV.
(3) On the center pedestal, on the SWITCHING panel 8VU, check that the ATT HDG selector switch is in NORM position.
Subtask 31-68-00-860-054-B ** ON A/C NOT FOR ALL (1) Do the EIS start procedure (PFDs and NDs only) (Ref. AMM TASK 31-60-00-860-001).
(2) On the overhead panel:
On the ADIRS CDU, on the panel 20VU, make sure that the OFF/NAV/ATT selector switches for ADIRU1 and ADIRU2 are at NAV.
(3) On the center pedestal, on the SWITCHING panel 8VU, check that the ATT HDG selector switch is in NORM position.
C. Aircraft Maintenance Configuration
(1) Do the EIS start procedure (PFDs and NDs only) (Ref. AMM TASK 31-60-00-860-001).
(2) On the ADIRS MSU, on the panel 20VU, make sure that the OFF/NAV/ATT selector switches for ADIRU1 and ADIRU2 are set to NAV.
(3) On the center pedestal, on the SWITCHING panel 8VU, make sure that the ATT HDG selector switch is set to NORM.
4. Procedure(1) Do the EIS start procedure (PFDs and NDs only) (Ref. AMM TASK 31-60-00-860-001).
(2) On the ADIRS MSU, on the panel 20VU, make sure that the OFF/NAV/ATT selector switches for ADIRU1 and ADIRU2 are set to NAV.
(3) On the center pedestal, on the SWITCHING panel 8VU, make sure that the ATT HDG selector switch is set to NORM.
Subtask 31-68-00-710-051-A ** ON A/C NOT FOR ALL
A. Check of the ATT HDG switch
Subtask 31-68-00-710-051-B ** ON A/C NOT FOR ALL | ACTION | RESULT |
|---|---|
| 1.On the ADIRS CDU: | |
| On the CAPT PFD, check that the pitch and roll attitudes and the heading indications go out of view. The ATT flag comes into view. Ignore the related warnings. |
| On the F/O PFD, check that the pitch and roll attitudes and the heading indications go out of view. The ATT flag comes into view. Ignore the related warnings. |
A. Check of the ATT HDG Switch
Subtask 31-68-00-020-052-A | ACTION | RESULT |
|---|---|
| 1.On the ADIRS MSU: | |
| On the CAPT PFD, the pitch and roll attitudes and the heading indications go out of view. The ATT flag comes into view. Ignore the related warnings. |
| On the F/O PFD, the pitch and roll attitudes and the heading indications go out of view. The ATT flag comes into view. Ignore the related warnings. |
B. Deactivation of the ATT HDG selector switch
(1) On the SWITCHING panel 8VU, near the ATT HDG selector switch, put a placard in position to tell the crew that no position other than the NORM position is permitted.
5. Close-up(1) On the SWITCHING panel 8VU, near the ATT HDG selector switch, put a placard in position to tell the crew that no position other than the NORM position is permitted.
Subtask 31-68-00-860-055-A
A. Aircraft Maintenance Configuration
(1) Do the EIS Stop Procedure (Ref. AMM TASK 31-60-00-860-002)
(2) Do the ADIRS Stop Procedure (Ref. AMM TASK 34-10-00-860-005)
(3) Make an entry in the log book.
(4) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002)
(1) Do the EIS Stop Procedure (Ref. AMM TASK 31-60-00-860-002)
(2) Do the ADIRS Stop Procedure (Ref. AMM TASK 34-10-00-860-005)
(3) Make an entry in the log book.
(4) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002)