Adjustment of the Aileron

TASK 27-14-00-820-001-A
Adjustment of the Aileron

ZONE: 210
ZONE: 575
ZONE: 675

1. Reason for the Job

NOTE: This task can contribute to fuel savings.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	1	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	1	RULE
No specific	1	RULER - GRADUATED
No specific	AR	WARNING NOTICE(S)
98D27903500000	2	PIN-SIDE STICK LOCKING

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.14QFB1)	Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD
575	AFT OUTBD SE OF WING AND TE FIXED STRUCT
675	AFT OUTBD SE OF WING AND TE FIXED STRUCT
575KB, 675KB, 822

D. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 27-14-00-200-001-A	Check of the Aileron Servo Control Oscillations
TASK 29-10-00-863-001-A	Pressurize the Green Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-003-A	Pressurize the Blue Hydraulic System with a Hydraulic Ground Power-Cart
TASK 29-10-00-863-003-A-01	Pressurize the Blue Hydraulic System with the Blue Electric Pump
TASK 29-10-00-864-001-A	Depressurize the Green Hydraulic System
TASK 29-10-00-864-003-A	Depressurize the Blue Hydraulic System
TASK 29-23-00-863-001-A	Pressurize the Green Hydraulic System from the Yellow Hydraulic System through the PTU with the Electric Pump
TASK 29-23-00-864-001-A	Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU
TASK 31-60-00-860-001-A	EIS Start Procedure
TASK 31-60-00-860-002-A	EIS Stop Procedure
Position of the Aileron Servocontrol
Aileron Adjustment

3. Job Set-up
Subtask 27-14-00-861-053-A

A. Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).

Subtask 27-14-00-865-053-A

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B11
49VU	FLIGHT CONTROLS/FCDC1/SPLY	20CE1	B10
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
49VU	AUTO FLT/FAC1/28VDC	5CC1	B04
49VU	AUTO FLT/FAC1/26VAC	14CC1	B03
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/ELAC1/NORM/SPLY	15CE1	B06
49VU	FLIGHT CONTROLS/FCDC1/SPLY	20CE1	B05
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B03
49VU	AUTO FLT/FAC1/28VDC	5CC1	H10
49VU	AUTO FLT/FAC1/26VAC	14CC1	H09
** ON A/C ALL
105VU	FLIGHT CONTROLS/ELAC2/STBY SPLY	16CE2	A02
105VU	FLT CTL/ELAC1/STBY SPLY	16CE1	A01
** ON A/C NOT FOR ALL
121VU	PTR/SPLY	6TW	J21
121VU	CFDS/CFDIU/SPLY	2TW	J18
121VU	CFDS/CFDIU/BACK/UP	8TW	J17
** ON A/C ALL
121VU	FLIGHT CONTROLS/FCDC2/SPLY	20CE2	Q20
121VU	FLIGHT CONTROLS/ELAC2/NORM/SPLY	15CE2	R20
** ON A/C NOT FOR ALL
121VU	PTR/SPLY	6TW	J44
121VU	CFDS/CFDIU/SPLY	2TW	J41
121VU	CFDS/CFDIU/BACK/UP	8TW	J40

Subtask 27-14-00-860-064-A

C. Aircraft Maintenance Configuration
(1) On the panel 23VU, make sure that the FLT CTL/ELAC1 pushbutton switch is pushed (on this pushbutton switch, the OFF and FAULT legends are off).
(2) On the panel 24VU, make sure that the FLT CTL/ELAC2 pushbutton switch is pushed (on this pushbutton switch, the OFF and FAULT legends are off).
(3) Make sure that all the hydraulic systems are depressurized.
(4) On the center pedestal, make sure that the flap and slat control lever is in the O position.
(5) On the center pedestal, make sure that the speed brake control lever is in the RET position.
(6) Pressurize the Green and Blue hydraulic systems (Ref. AMM TASK 29-10-00-863-001) or (Ref. AMM TASK 29-23-00-863-001) and (Ref. AMM TASK 29-10-00-863-003).
(7) Operate the aileron ten times with the side stick to bleed the system.
(8) On the panel 23 VU, release the FLT CTL/ELAC1 pushbutton switch (on this pushbutton switch, the OFF legend comes on).
(9) Operate the aileron ten times with the side stick to bleed the system.
(10) Put the side stick in the neutral position.
(11) Install the 98D27903500000 PIN-SIDE STICK LOCKING on the side sticks.
(12) Put the WARNING NOTICE(S) on the CAPT and F/O side sticks to tell persons not to operate the side sticks.
(13) On the panel 23 VU, push the FLT CTL/ELAC1 pushbutton switch (on this pushbutton switch, the OFF legend goes off).
(14) Depressurize the Green hydraulic system (Ref. AMM TASK 29-10-00-864-001) or (Ref. AMM TASK 29-23-00-864-001).

Subtask 27-14-00-010-051-A

D. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE at the access door 822.
(2) Open the access door 822.
(3) Open the battery power center 105VU:

loosen the two screws and remove the protective cover.

(4) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone:
(a) 575 for the left aileron,
(b) 675 for the right aileron.
(5) Open the access door:
(a) 575KB for the left aileron,
(b) 675KB for the right aileron.

NOTE: For an easier access for adjustment of the aileron servocontrol, remove the rubbing strip seal, if necessary.

4. Procedure
Subtask 27-14-00-820-052-A

A. Adjustment of the Aileron when the Blue Outboard Servocontrol is Pressurized.

NOTE: If you see oscillations when the servocontrol is in the active mode, do a check of these oscillations (Ref. AMM TASK 27-14-00-200-001).

NOTE: To adjust an aileron, you must adjust the surface with one servocontrol active and then the other.

NOTE: At this time, the Blue servocontrol (33CE3, 33CE4) is in the active mode.

(1) Put a RULE in position on the trailing edge of the wing (inboard end of the wing) (see detail E).
(2) Use a RULER - GRADUATED to measure the position of the aileron in relation to the RULE .

NOTE: To optimize the theoretical loft line, the ailerons position must be as close as possible to the nominal values.
If the position of the aileron is not satisfactory, adjust the Blue servocontrol as follows:

(a) Cut and remove the lockwire from the bolts (3).
(b) Remove the bolts (3) and the lock plate (1).
(c) Set the control surface to zero with the adjusting nut (2).

NOTE: Always turn the adjusting nut (2) in the same direction to adjust the clearances and the hysteresis.

NOTE: If you turn the adjusting nut (2) clockwise while you look in the aircraft nose direction, the aileron trailing edge will move down.

(d) Install the lock plate (1) and the bolts (3).
(e) Safety the bolts (3) with the 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.
(3) Pressurize the Green hydraulic system (Ref. AMM TASK 29-10-00-863-001) or (Ref. AMM TASK 29-23-00-863-001)
(4) Depressurize the Blue hydraulic system (Ref. AMM TASK 29-10-00-864-003).

Subtask 27-14-00-820-053-A

B. Adjustment of the Aileron when the Green Inboard Servocontrol is Pressurized.

NOTE: If you see oscillations when the servocontrol is in the active mode, do a check of these oscillations (Ref. AMM TASK 27-14-00-200-001).

NOTE: To adjust an aileron, you must adjust the surface with one servocontrol active and then the other.

NOTE: At this time, the Green servocontrol (33CE1, 33CE2) is in the active mode.

(1) Use a RULER - GRADUATED to measure the position of the aileron in relation to the RULE .

(a) Cut and remove the lockwire from the bolts (3).
(b) Remove the bolts (3) and the lock plate (1).
(c) Set the control surface to zero with the adjusting nut (2).

NOTE: Always turn the adjusting nut (2) in the same direction to adjust the clearances and the hysteresis.

NOTE: If you turn the adjusting nut (2) clockwise while you look in the aircraft nose direction, the aileron trailing edge will move down.

(d) Install the lock plate (1) and the bolts (3).
(e) Safety the bolts (3) with the lockwire.
(2) Remove the RULE from the trailing edge of the wing.
(3) On the panel 24VU, make sure that the OFF and FAULT legends of the FLT CTL/ELAC 2 pushbutton switch are off.

Subtask 27-14-00-860-063-A

C. Aircraft Maintenance Configuration
(1) Remove the rigging pins and the warning notices from the side sticks.
(2) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
(3) On the center pedestal, on the ECAM control panel, push the F/CTL key (on the lower ECAM D.U, the F/CTL page comes into into view).
(4) Pressurize the Blue hydraulic system (Ref. AMM TASK 29-10-00-863-003).
(5) On the panel 23 VU, release the FLT CTL/ELAC1 pushbutton switch (on this pushbutton switch, the OFF legend comes on).

Subtask 27-14-00-710-052-A

D. Do this test:

ACTION	RESULT
1.In the CAPT or F/O seat: move the side stick until it touches the left stop and hold it in this position.	The left aileron moves up smoothly. The right aileron moves down smoothly. On the F/CTL page of the lower ECAM DU: the index of the L/AIL indicator moves smoothly to the upper stop. the index of the R/AIL indicator moves smoothly to the lower stop.
2.In the CAPT or F/O seat: move the side stick from the left stop until it touches the right stop and hold it in this position.	The left aileron moves down smoothly. The right aileron moves up smoothly. On the F/CTL page of the lower ECAM DU: the index of the L/AIL indicator moves smoothly from the upper stop until it touches the lower stop. the index of the R/AIL indicator moves smoothly from the lower stop until it touches the upper stop.
3.In the CAPT or F/O seat: put the side stick in the neutral position.	The left aileron moves smoothly to the neutral position. The right aileron moves smoothly to the neutral position. On the F/CTL page of the lower ECAM DU: the index of the L/AIL indicator moves smoothly to the neutral mark. the index of the R/AIL indicator moves smoothly to the neutral mark.
	Make sure that no fault indication come into view.
4.On the panel 23VU: push the FLT CTL/ELAC 1 pushbutton switch.	On the panel 23VU: the OFF legend of the FLT CTL/ELAC 1 pusbutton switch goes off.
5.On the panel 24VU: release the FLT CTL/ELAC 2 pushbutton switch.	On the panel 24VU: the OFF legend of the FLT CTL/ELAC 2 pushbutton switch comes on.
6.In the CAPT or F/O seat: move the side stick until it touches the left stop and hold it in this position.	The left aileron moves up smoothly. The right aileron moves down smoothly. On the F/CTL page of the lower ECAM DU: the index of the L/AIL indicator moves smoothly to the upper stop. the index of the R/AIL indicator moves smoothly to the lower stop.
7.In the CAPT or F/O seat: move the side stick from the left stop until it touches the right stop and hold it in this position.	The left aileron moves down smoothly. The right aileron moves up smoothly. On the F/CTL page of the lower ECAM DU: the index of the L/AIL indicator moves smoothly from the upper stop until it touches the lower stop. the index of the R/AIL indicator moves smoothly from the lower stop until it touches the upper stop.
8.In the CAPT or F/O seat: put the side stick in the neutral position.	The left aileron moves smoothly to the neutral position. The right aileron moves smoothly to the neutral position. On the F/CTL page of the lower ECAM DU: the index of the L/AIL indicator moves smoothly to the neutral mark. the index of the R/AIL indicator moves smoothly to the neutral mark.
	Make sure that no fault indication comes into view.

5. Close-up
Subtask 27-14-00-860-065-A

A. Aircraft Maintenance Configuration
(1) Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
(2) On the panel 24VU, push the FLT CTL/ELAC2 pushbutton switch (on this pushbutton switch, the OFF legend goes off).
(3) Depressurize the Green and Blue hydraulic systems (Ref. AMM TASK 29-10-00-864-001) or (Ref. AMM TASK 29-23-00-864-001) and (Ref. AMM TASK 29-10-00-864-003).
(4) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).
(5) Make sure that the work area is clean and clear of tools and other items.

Subtask 27-14-00-410-051-A

B. Close Access
(1) Close the access door :
(a) 575KB for the left aileron.
(b) 675KB for the right aileron.
(2) Install the protective cover on the battery power center 105VU.
(3) Tighten the two screws.
(4) Close the access door 822.
(5) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.01 06:47:10 UTC