71-00 (IAE) - POWER PLANT - GENERAL

71-00-00 (IAE) - POWER PLANT - GENERAL

PB.001 CONF:[13] POWER PLANT - GENERAL - DESCRIPTION AND OPERATION
PB.201 CONF:[13] POWER PLANT - GENERAL - MAINTENANCE PRACTICES
- 71-00-00-500-010-A [IAE] [10]
  List of Preservation Procedures
- 71-00-00-550-010-A [IAE] [10]
  General Data for Storage of Installed Engines
- 71-00-00-550-011-A [IAE] [10]
  Depreservation of Installed Engine
- 71-00-00-100-010-A [IAE] [10]
  Clean and Examine the Power Plant
- 71-00-00-600-011-A [IAE] [10]
  Protect the Engine External Surfaces
- 71-00-00-550-012-A [IAE] [10]
  Preservation of the Main Line Bearings
- 71-00-00-860-011-C [IAE] [10]
  Table of Idle Indications
- 71-00-00-860-011-C-01 [IAE] [10]
  Table of Idle Indications
- 71-00-00-860-013-A [IAE] [10]
  Oil and Fuel Systems Priming Procedure
- 71-00-00-860-014-A [IAE] [10]
  Procedure After the Use of Fire Extinguishing Agents
- 71-00-00-860-012-A [IAE] [10]
  Engine Safety Precautions
- 71-00-00-860-010-B [IAE] [10]
  Engine Operation Limits, Guidelines and Special Procedures
- 71-00-00-710-015-A [IAE] [10]
  Procedure for an Emergency Shutdown
- 71-00-00-710-018-A [IAE] [10]
  Discontinued Start, Restart and Shutdown Procedures
- 71-00-00-710-019-B [IAE] [10]
  Procedure After Engine Surge or Stall (No Overtemperature)
- 71-00-00-710-043-A [IAE] [10]
  Normal Engine Automatic-Start Procedure
- 71-00-00-710-047-A [IAE] [10]
  Normal Engine Manual-Start Procedure
- 71-00-00-710-021-A [IAE] [10]
  Procedure for an Emergency Shutdown (New or Overhauled Engines)
- 71-00-00-600-010-A [IAE] [10]
  Inhibit the Engine Fuel System
- 71-00-00-700-040-A [IAE] [10]
  Procedure after Accidental Opening of the Thrust Reverser Pressure Relief Door
- 71-00-00-700-014-B [IAE] [10]
  Cold Weather Operation Procedure
- 71-00-00-700-016-A [IAE] [10]
  Procedure for a Bowed Rotor Start Prevention
- 71-00-00-710-023-A [IAE] [10]
  Emergency Procedures in case of Engine Fire
PB.501 CONF:[13] POWER PLANT - GENERAL - ADJUSTMENT/TEST
- 71-00-00-710-017-B [IAE] [10]
  Ground Test Requirements after Power Plant Module/Component Repair or Replacement Procedures
- 71-00-00-710-045-A [IAE] [10]
  Test No.1 : Dry Motor Leak Check
- 71-00-00-710-046-B [IAE] [10]
  Test No.2 : Wet Motor Leak Check
- 71-00-00-710-012-B [IAE] [10]
  Test No.3 : Idle Leak Check
- 71-00-00-710-022-B [IAE] [10]
  Test No. 6: Electronic Engine Control (EEC) System Idle Test
- 71-00-00-700-022-B [IAE] [10]
  Test No.8 : Vibration Survey
- 71-00-00-700-012-B [IAE] [10]
  Test No.9 : Low Pressure (LP) Compressor (Fan) Trim Balancing - One Shot Method
- 71-00-00-700-012-B-01 [IAE] [10]
  Test No.9A : LP Compressor (Fan) Trim Balancing - Trial Weight Method
- 71-00-00-710-013-C [IAE] [10]
  Test No.11 : High Power Assurance Test
- 71-00-00-700-011-B [IAE] [10]
  Test No.13 : Pretested Replacement Engine Test
- 71-00-00-700-013-A [IAE] [10]
  Procedure to Dry Out the High Pressure Turbine (HPT) after Oil Contamination
- 71-00-00-710-016-A [IAE] [10]
  Test No.14 : Pressure Raising Valve Operational Check (POST SBE 73-1098)

71-00-20 (IAE) - POWER PLANT - DEMOUNTABLE

PB.401 CONF:[13] POWER PLANT - DEMOUNTABLE - REMOVAL/INSTALLATION
- 71-00-20-000-040-A [IAE] [10]
  Removal of the Power Plant
- 71-00-20-000-040-A-01 [IAE] [10]
  Removal of the Power Plant with the Engine Positioner TWW 75E (MIAG)
- 71-00-20-400-040-A [IAE] [10]
  Installation of the Power Plant
- 71-00-20-400-040-A-01 [IAE] [10]
  Installation of the Power Plant with the Engine Positioner TWW 75E (MIAG)
- 71-00-20-400-802-A [IAE] [10]
  Reload the Power Plant
- 71-00-20-000-802-A [IAE] [10]
  Unload the Power Plant
- 71-00-20-000-040-A-02 [IAE] [8]
  Removal of the Power Plant with Cobra Tool
- 71-00-20-400-040-A-02 [IAE] [8]
  Installation of the Power Plant with Cobra Tool
PB.601 CONF:[13] POWER PLANT - DEMOUNTABLE - INSPECTION/CHECK
- 71-00-20-200-010-A [IAE] [10]
  Examine the Engine Mount Bolts