Read the LRU Identification Report (Menu Mode) [CFML]

TASK 73-29-00-740-809-A
Read the LRU Identification Report (Menu Mode)

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

ZONE: 210

1. Reason for the Job
The LRU IDENTIFICATION function in menu mode provides the operator with the following engine and LRU details:
(a) Engine thrust rating
(b) EEC part number and ATA
(c) PSS part number and ATA
(d) AS software part number (SW1)
(e) OMAP software part number (SW2)
(f) Engine Bump available (Yes/No)
(g) N1 Trim (0 through 7)
(h) Engine serial number
(i) EEC serial number and ATA
(j) PSS serial number and ATA
(k) Engine hardware configuration (01-16)
(l) HPT deteriorated (Y/N).
The LRU IDENTIFICATION function in menu mode provides the operators with these additional aircraft and LRU details:
(m) Prognostic and health management software part number (SW3)
(n) Modulated turbine cooling configuration
(o) Accelerometer configuration
(p) Aircraft type.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-32-00-860-012-A	Procedure to Get Access to the SYSTEM REPORT/TEST/ENG Page
TASK 32-69-00-860-001-A	Simulation of Flight (With Aircraft on Ground)
TASK 73-29-00-740-810-A	Entry of the Engine Serial Number (ESN) (Menu Mode)
FUNCTION TERMINATED Screen
Menu Mode Main Menu - Screen 1
LRU IDENTIFICATION Report Screen 1 Format
LRU IDENTIFICATION Report Screen 2 Format
LRU IDENTIFICATION Report Screen 3 Format

3. Job Set-up
Subtask 73-29-00-861-072-A

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 73-29-00-941-068-A

B. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Put WARNING NOTICE(S) in position to tell persons not to operate:

The ENG/MODE selector switch, and
The ENG/MASTER 1(2) control switch.

(2) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 73-29-00-865-085-A

C. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
49VU	L/G/LGCIU/SYS1/NORM	1GA	C09
121VU	HYDRAULIC/LGCIU/SYS2	2GA	Q35
121VU	HYDRAULIC/LGCIU/SYS1/GRND SPLY	52GA	Q34
FOR FIN: 4020KM1 (POWER PLANTDEMOUNTABLE, ENGINE 1)
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R40
FOR FIN: 4020KM2 (POWER PLANTDEMOUNTABLE, ENGINE 2)
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/ENG2/FADEC B/AND EIU2	4KS2	R41

Subtask 73-29-00-860-100-A

D. Aircraft Maintenance Configuration
(1) On the ENG section of maintenance panel 50VU:

Release the FADEC GND PWR 1(2) pushbutton switch (the ON legend comes on).

(2) After the FADEC is energized, wait a minimum of 60 seconds before you start the test. If you do not wait 60 seconds, the interactive mode stops the EEC self-test which can cause unwanted faults and the OMAP software part number (SW2) will not be displayed.
(3) On the left or right Multipurpose Control and Display Unit (MCDU), get the SYSTEM REPORT/TEST/ENG page (Ref. AMM TASK 31-32-00-860-012).
(4) Make sure that the landing gear system is not simulated in the flight configuration (Ref. AMM TASK 32-69-00-860-001).

4. Procedure
Subtask 73-29-00-710-075-A

A. General
(1) A sub-function allows modification of the engine serial number, perform task (Ref. AMM TASK 73-29-00-740-810) to modify the engine serial number.

NOTE: The following list provides the letter format designations for the LRU IDENTIFICATION Report:

LRU IDENTIFICATION Report Screen 1 Format

LRU IDENTIFICATION Report Screen 2 Format

LRU IDENTIFICATION Report Screen 3 Format

"F" = 1 digit engine designation (engine 1 or 2)
"C" = 1 letter EEC channel designation (channel A or B)
"TTTT" = Thrust rating
"XXXXXXXXXX" = Last 10 digits of EEC part number
"DDDDDD" = 6-digit EEC ATA number
"PPPPPPPPPP" = PSS Part Number
"AAAAAA" = 6-digit PSS ATA number
"SSSSSSSSSS" = EEC Software part number (SW1)
"OOOOOOOOOO" = OMAP Software part number (SW2)
"B" = Bump available (Y - Yes / N - No)
"N" = 1-digit N1 trim designation (0-7)
"SSSSSS" = 6-digit engine serial number (ESN)
"QQQQQQQQ" = ECC serial number
"RRRRRRRRR" = PSS serial number
"JJ" = Hardware configuration (01-16)
"H" = HPT deteriorated (Y/N).
"VVVVVVVVVV" = EEC Prognostic and health management software part number
"MMMMMM" = Modulated turbine cooling configuration stored in NVM (SINGLE or DUAL)
"HHHH" = Accelerometer configuration (NORM, TCF or PX36)
"AAAAAAA" = Aircraft type

NOTE: The EEC will not enter the menu mode (interactive mode) after an enquire command from the CFDS (Centralized Fault Display System) when any of the following conditions are set:

N2 more than ten percent or invalid
Rotary selector on CRANK or IGN/START or invalid
Manual Start Button ON or invalid
Throttle Lever Angle (TLA) not at idle or invalid
Aircraft in the air
MASTER lever ON or invalid
BITE command code input label invalid.

NOTE: The EEC will abort a running test or special function when any of the following conditions becomes set:

N2 more than ten percent or invalid
Engine state not off
Engine not in default start state
TLA not at idle or invalid
Aircraft in the air
MASTER lever ON or invalid
You enter in the interactive mode of the other channel.

Subtask 73-29-00-740-052-A

B. Do the LRU Identification function in Menu Mode

ACTION	RESULT
1.On the Menu Mode main menu page 1, Menu Mode Main Menu - Screen 1 push the key adjacent to LRU IDENT REPORT (3L).	The LRU IDENTIFICATION page 1 screen is shown. LRU IDENTIFICATION Report Screen 1 Format If OMAP software part number (SW2) is not displayed, exit the LRU Identification Report, wait 5 minutes and then try again.
2.Review engine and LRU details. If an engine serial number change is necessary, see (Ref. AMM TASK 73-29-00-740-810).	NOTE: If one of the following conditions occurs while the LRU IDENTIFICATION screen is displayed, the function is aborted and the FUNCTION TERMINATED screen is displayed: FUNCTION TERMINATED Screen Engine is not in the OFF state Master Lever is set to ON or signal is invalid Core Speed (N2) is above 10% or invalid Throttle Lever Angle (TLA) not at idle or TLA signals invalid FADEC channel switch requested by standby channel Aircraft indicates in air.
3.Select the key adjacent to PAGE 2 (5L) to view additional engine and LRU details. LRU IDENTIFICATION Report Screen 2 Format	The LRU IDENTIFICATION page 2 is shown. LRU IDENTIFICATION Report Screen 2 Format
4.Select the key adjacent to PAGE 3 (5L) to view additional engine and LRU details. LRU IDENTIFICATION Report Screen 3 Format	The LRU IDENTIFICATION page 3 is shown. LRU IDENTIFICATION Report Screen 3 Format
5.Select the key adjacent to RETURN (6L) to the main menu. If the FUNCTION TERMINATED screen is displayed, verify the cockpit settings as indicated on: FUNCTION TERMINATED Screen Set the Master Lever to OFF. Set the Manual Start button to OFF. Set the Start Switch to NORM. Press the key adjacent to RETURN (6L) to return to the main menu.	The Menu Mode main menu is shown. Menu Mode Main Menu - Screen 1

5. Close-up
Subtask 73-29-00-860-101-A

A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) On the ENG section of maintenance panel 50VU:
(a) Release the FADEC GND PWR 1(2) pushbutton switch (the ON legend goes off).
(3) Remove the WARNING NOTICE(S).

Subtask 73-29-00-862-072-A

B. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 03:06:09 UTC