Installation of the Engine Drain Mast [PW11]

TASK 71-71-01-400-802-A
Installation of the Engine Drain Mast

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	Torque wrench: range to between 35 and 31.5 lbf.in (0.40 and 0.36 m.daN )

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-860-833-A	Procedure to Prevent Engine Motoring
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-802-A	Closing of the Fan Cowl Doors
TASK 71-71-49-000-801-A	Removal of the Engine Drain Tubes and Pylon Drain Hoses
TASK 71-71-49-400-801-A	Installation of the Engine Drain Tubes and Pylon Drain Hoses
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-805-A	Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
TASK 78-36-00-410-802-A	Closing of the Thrust Reverser Cowl-Doors
Engine Drain Mast

3. Job Set-up
Subtask 71-71-01-941-053-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Make sure that you did the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).

Subtask 71-71-01-010-056-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR

Subtask 71-71-01-040-053-A ** ON A/C NOT FOR ALL

C. Deactivation of the Thrust Reverser System for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Make sure that you did the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 71-71-01-010-057-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Make sure that the right thrust reverser cowl-door is open (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
462AR

Subtask 71-71-01-840-050-A ** ON A/C NOT FOR ALL

E. Make sure that the engine drain tubes are correctly installed (Ref. AMM TASK 71-71-49-400-801).

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 71-71-01-420-051-A ** ON A/C NOT FOR ALL

A. Installation of the Engine Drain Mast
(1) Removal of the protection covers

CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY TO PREVENT ENGINE DAMAGE.

(a) Make sure that you remove all the necessary COVER - PROTECTION to prevent damage to the engine and adjacent components.
(2) Installation of the drain mast assembly (5) as follows:
(a) Install the bracket (2), four spacers (3), lower line block (4) and drain mast assembly (5) on the brackets on the drain tubes. Use the four bolts (1).
(b) Make sure there is no preload on the drain tubes. If you find preload, loosen the drain tubes as necessary, adjust the tubes to remove the preload and tighten them again (Ref. AMM TASK 71-71-49-000-801) and (Ref. AMM TASK 71-71-49-400-801).
(c) TORQUE the four bolts (1) to between 35 and 31.5 lbf.in (0.40 and 0.36 m.daN )

5. Close-up
Subtask 71-71-01-410-052-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the right thrust reverser cowl-door (Ref. AMM TASK 78-36-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
462AR

Subtask 71-71-01-440-051-A ** ON A/C NOT FOR ALL

B. Do the reactivation of the thrust reverser system after maintenance (Ref. AMM TASK 78-30-00-440-805).

Subtask 71-71-01-410-053-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR
(2) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 02:33:54 UTC