Special Detailed Inspection (US) of Pylon Forward Mount Fitting, End of Lower Arms, Aft of RIB 1, Forward Attachment, Bolt Holes

TASK 54-51-00-200-002-A
Special Detailed Inspection (US) of Pylon Forward Mount Fitting, End of Lower Arms, Aft of RIB 1, Forward Attachment, Bolt Holes

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 410
ZONE: 420
FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Refer to the MPD TASK: 545102-01
SPECIAL DETAILED INSPECTION (US) OF PYLON FORWARD MOUNT FITTING, END OF LOWER ARMS, AFT OF RIB 1, FORWARD ATTACHMENT, BOLT HOLES

NOTE: The effectivity of this task is "ALL". To know if this task is applicable to your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
410	ENG 1 PYLON BOX AND FORWARD FAIRING
420	ENG 2 PYLON BOX AND FORWARD FAIRING
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-081-041-A	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-081-041-B	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-440-012-A	Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
TASK 78-32-00-410-010-A	Closing of the Thrust Reverser Halves
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-A	Closing of the Thrust Reverser Doors
TASK 78-36-00-410-040-B	Closing of the Thrust Reverser Doors
NTM 545102
SRM 511100	(for corrective action)
SRM 512200	(for corrective action)
Inspection (US) of the Pylon Forward Mount-Fitting, Forward Attachment, Bolt Holes ** ON A/C NOT FOR ALL
Inspection (US) of the Pylon Forward Mount-Fitting, Forward Attachment, Bolt Holes ** ON A/C NOT FOR ALL
Inspection (US) of the Pylon Forward Mount-Fitting, Forward Attachment, Bolt Holes ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 54-51-00-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to start engine 1(2).
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 54-51-00-040-052-A ** ON A/C NOT FOR ALL

B. Deactivation of the Thrust Reverser

WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.

(1) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-481-041).

Subtask 54-51-00-010-051-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Open the thrust reverser doors (Ref. AMM TASK 78-36-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR.
(3) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position:
(a) For the left pylon, in zone 415
(b) For the right pylon, in zone 425.

Subtask 54-51-00-040-052-B ** ON A/C NOT FOR ALL

D. Deactivation of the Thrust Reverser

WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.

(1) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-040-012).

Subtask 54-51-00-010-051-B ** ON A/C NOT FOR ALL

E. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Open the thrust reverser doors (Ref. AMM TASK 78-32-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR.
(3) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position:
(a) For the left pylon, in zone 415
(b) For the right pylon, in zone 425.

Subtask 54-51-00-110-052-A ** ON A/C NOT FOR ALL

F. Preparation of the Inspection Area

Inspection (US) of the Pylon Forward Mount-Fitting, Forward Attachment, Bolt Holes ** ON A/C NOT FOR ALL

(1) Clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) , if necessary.
(2) Make sure that the surface of the inspection area is clean and smooth.
(3) Do a visual check of the inspection area for damage or discontinuities.
(4) Make sure that there is no:
(a) Corrosion damage:
- If you find corrosion damage, refer to Structural Repair Manual SRM 512200 for types of corrosion, inspection, removal and corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
- If you find this type of damage, refer to Structural Repair Manual SRM 511100 for damage classification and corrective action.

4. Procedure
Subtask 54-51-00-270-051-A ** ON A/C NOT FOR ALL

A. Inspection

Inspection (US) of the Pylon Forward Mount-Fitting, Forward Attachment, Bolt Holes ** ON A/C NOT FOR ALL

(1) Do a special detailed inspection (US) of the forward attachment bolt holes of the end of the lower arms. This inspection is applicable aft of RIB1. Refer to Non-destructive Testing Manual NTM 545102.
(a) For the inspection of the hole types A:
Do the inspection on each side of each pylon.
(2) Make a report of damage after NDT inspection:
(a) Corrosion damage:
- If you find corrosion damage, refer to Structural Repair Manual SRM 512200 for types of corrosion, inspection, removal and corrosion protection.
(b) Other damage (scratches, cracks, gouges, dents, creases):
- If you find this type of damage, refer to Structural Repair Manual SRM 511100 for damage classification and corrective action.

5. Close-up
Subtask 54-51-00-410-051-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Close the thrust reverser doors (Ref. AMM TASK 78-36-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.

Subtask 54-51-00-440-052-A ** ON A/C NOT FOR ALL

B. Reactivation of the Thrust Reverser
(1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-081-041).

Subtask 54-51-00-410-051-B ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the thrust reverser doors (Ref. AMM TASK 78-32-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.

Subtask 54-51-00-440-052-B ** ON A/C NOT FOR ALL

D. Reactivation of the Thrust Reverser
(1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-440-012).

Subtask 54-51-00-942-050-A ** ON A/C NOT FOR ALL

E. Aircraft Maintenance Configuration
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 01:59:23 UTC