Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance [IAE]

TASK 78-30-00-440-012-A
Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance

ZONE: 400
FIN: 4101KS1 ** ON A/C NOT FOR ALL
FIN: 4101KS2 ** ON A/C NOT FOR ALL

1. Reason for the Job
This procedure supplies the data to put the thrust reverser Hydraulic Control Unit (HCU) back in operation.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)
IAE1N20010	1	LOCKOUT PIN - THRUST REVERSER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 78-31-00-710-041-A	Operational Test of the Thrust Reverser System with the CFDS
TASK 78-31-00-710-041-A-02	Operational test of the Thrust Reverser without the CFDS and Engine Running
Thrust Reverser Hydraulic Control Unit (HCU)

3. Job Set-up
Subtask 78-30-00-860-051-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.

Subtask 78-30-00-010-060-A ** ON A/C NOT FOR ALL

B. Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR.

4. Procedure
Subtask 78-30-00-440-054-A ** ON A/C NOT FOR ALL

A. Activate the Thrust Reverser HCU

Thrust Reverser Hydraulic Control Unit (HCU) ** ON A/C NOT FOR ALL

(1) Remove the IAE1N20010 LOCKOUT PIN - THRUST REVERSER (2) from the HCU (1) and let the lock lever (3) go back to the unlock position.
(2) Make sure that the lock lever (3) has moved fully to its normal position.

5. Close-up
Subtask 78-30-00-410-056-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowls (Ref. AMM TASK 71-13-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).

Subtask 78-30-00-710-073-A ** ON A/C NOT FOR ALL

B. Operational Test
(1) Do the operational test of the thrust reverser system (Ref. AMM TASK 78-31-00-710-041).

NOTE: As an alternative procedure, you can do the operational test without the centralized fault display system:

The method with the engine running (Ref. AMM TASK 78-31-00-710-041).

[Rev.10 from 2021] 2026.04.01 03:51:34 UTC