Installation of the Low Oil Pressure Switch (131-9(A))

TASK 49-94-14-400-003-A
Installation of the Low Oil Pressure Switch (131-9(A))

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

FIN: 8091KM ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	CONTAINER 3 L(3/4 USGAL)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.03ABA1)	Synthetic base Lubricating Oil-Turbine Engine - -
(Material No.03ABB1)	Synthetic base Lubricating Oil-Turbine Engine Low Temp. -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
315AL, 316AR

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
3	PACKING	AIPC 49-94-09-01-030

E. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 49-00-00-860-008-A	APU Start by External Power
TASK 49-00-00-860-008-A-01	APU Start by Batteries
TASK 49-00-00-860-009-A	APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01	APU Shutdown by Batteries (131-9(A))
TASK 49-90-00-600-007-A	Check Oil Level and Replenish (131-9(A))
TASK 52-41-00-010-001-A	Open the APU Doors for Access
TASK 52-41-00-410-001-A	Close the APU Doors after Access
Low Oil Pressure Switch

3. Job Set-up
Subtask 49-94-14-860-057-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
(2) On the panel 25VU make sure that the APU MASTER SW p/bsw is OFF.
(3) Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.
(4) Make sure that the hydraulic systems are depressurized
(Ref. AMM TASK 29-00-00-864-001).
(5) Make sure that the access platform is in position below the APU compartment.
(6) Make sure that the APU access doors are open (Ref. AMM TASK 52-41-00-010-001).
(7) Make sure that the LIGHT SW 11LJ is set to the ON position.
(8) Make sure that the CONTAINER 3 L(3/4 USGAL) is in position below the LOP switch.

Subtask 49-94-14-865-059-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

Subtask 49-94-14-010-054-A ** ON A/C NOT FOR ALL

C. Make sure that the APU access doors 315AL and 316AR are open.

4. Procedure
Subtask 49-94-14-420-052-A ** ON A/C NOT FOR ALL

A. Installation of the Low Oil Pressure (LOP) Switch
(1) Apply a layer of Synthetic base Lubricating Oil-Turbine Engine - - (Material No.03ABA1) or Synthetic base Lubricating Oil-Turbine Engine Low Temp. - (Material No.03ABB1) to the new AIPC 49-94-09-01-030 PACKING (3).
(2) Install the new packing (3) on the LOP switch (2).
(3) Remove the blanking plug from the gearbox port.
(4) Install the LOP switch (2) in the gearbox.
(5) Tighten the bolt (4).
(6) Remove the container.
(7) Remove the blanking caps from the electrical connectors.
(8) Connect the electrical connector (1) to the LOP switch (2).

Subtask 49-94-14-210-052-A ** ON A/C NOT FOR ALL

B. Do a visual check of the oil quantity. (Ref. AMM TASK 49-90-00-600-007).

Subtask 49-94-14-865-060-A ** ON A/C NOT FOR ALL

C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

Subtask 49-94-14-710-053-A ** ON A/C NOT FOR ALL

D. Start and Operate the APU to check the System Report/Test on the MCDU
(1) Start and operate the APU (Ref. AMM TASK 49-00-00-860-008).
(2) Let the APU run for 5 minutes to check the System Report/Test on the MCDU.

NOTE: The SYSTEM SELF-TEST page must not show LOP switch.

(3) Shut down the APU (Ref. AMM TASK 49-00-00-860-009).
(4) Do a leak check of the LOP switch.

NOTE: No leaks are permitted.

5. Close-up
Subtask 49-94-14-410-052-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Set the LIGHT SW 11LJ to the OFF position.
(3) Close the APU access doors 315AL 316AR (Ref. AMM TASK 52-41-00-410-001).
(4) Remove the access platform(s).

Subtask 49-94-14-860-058-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration
(1) Put the related hydraulic system in the pressurized configuration (Ref. AMM TASK 29-00-00-864-001).
(2) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 12:41:58 UTC