Installation of the Catwalk Panel (131-9(A))

TASK 49-16-43-400-006-A
Installation of the Catwalk Panel (131-9(A))

ZONE: 314

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	1	FLASHLIGHT
No specific	1	WARNING NOTICE(S)
98L12003001000	1	HARNESS,SAFETY

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
314	TAIL CONE APU AIR INTAKE AREA
314AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 52-41-23-010-801-A	Opening of Access Door 314AR
TASK 52-41-23-410-801-A	Closing of Access Door 314AR
Catwalk Panel

3. Job Set-up
Subtask 49-16-43-860-064-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-41-00-861-002).
(2) On the overhead panel 25VU, make sure that the APU MASTER SW pushbutton switch is released (ON legend is off).
(3) On the APU section of overhead panel 25VU, make sure that the WARNING NOTICE(S) is in position to tell persons not to start the APU.
(4) Make sure that the hydraulic systems are depressurized
(Ref. AMM TASK 29-00-00-864-001).

Subtask 49-16-43-865-068-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

Subtask 49-16-43-010-058-A ** ON A/C NOT FOR ALL

C. Get Access

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(1) Make sure that the 98L12003001000 HARNESS,SAFETY is put and attached before you start work in the work area.
(2) Make sure that the access platform ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE is in position below access door 314AR.
(3) Make sure that access door 314AR is open and safetied in the open position.
(Ref. AMM TASK 52-41-23-010-801).
(4) If necessary, use a FLASHLIGHT.

4. Procedure
Subtask 49-16-43-420-059-B ** ON A/C NOT FOR ALL

A. Installation of the catwalk panel
(1) Put the catwalk panel (1) in position and install the bolts (2) and (4) with the washers (3).
(2) Tighten the bolts (2) and (4).

5. Close-up
Subtask 49-16-43-410-055-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close access door 314AR (Ref. AMM TASK 52-41-23-410-801).
(3) Remove the access platform(s).
(4) Remove the safety harness.

Subtask 49-16-43-865-069-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

Subtask 49-16-43-860-065-A ** ON A/C NOT FOR ALL

C. Aircraft Maintenance Configuration
(1) Put the related hydraulic system in the pressurized configuration (Ref. AMM TASK 29-00-00-864-001).
(2) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 12:42:30 UTC