Removal of the Lower High Pressure Duct

TASK 36-11-49-000-045-A
Removal of the Lower High Pressure Duct

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE
No specific	AR	COVER - PROTECTION
No specific	AR	PLUG - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 49-00-00-860-006-A	APU Shutdown by External Power
TASK 49-00-00-860-006-A-01	APU Shutdown by Batteries
TASK 49-00-00-860-009-A	APU Shutdown by External Power (131-9(A))
TASK 49-00-00-860-009-A-01	APU Shutdown by Batteries (131-9(A))
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
High Pressure (HP) Ducts

3. Job Set-up
Subtask 36-11-49-861-066-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002) or (Ref. AMM TASK 24-41-00-861-002).

Subtask 36-11-49-941-056-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(2) On the AIR COND panel 30VU:

make sure that the ENG 1(2) BLEED pushbutton switch is released (the OFF legend is on),
make sure that the APU BLEED pushbutton switch is released (the ON legend is off),
put a WARNING NOTICE(S) to tell persons not to operate the pneumatic system.

(3) On the ENG panel 115VU:

put a WARNING NOTICE(S) to tell persons not to start the engine 1(2).

(4) On the HP ground connector:

Put a WARNING NOTICE(S) to tell persons not to pressurize the pneumatic system.

(5) On the ENG section of the maintenance panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off,
put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 36-11-49-865-059-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	AIR BLEED/ENG 1/CTL	3HA1	D12
49VU	AIR BLEED/ENG 1/MONG	2HA1	D11
122VU	AIR BLEED/ENG 2/CTL	3HA2	Z23
122VU	AIR BLEED/ENG 2/MONG	2HA2	Z22

Subtask 36-11-49-010-053-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE in position in zone 450 for engine 1 and in zone 460 for engine 2.

Subtask 36-11-49-040-061-A ** ON A/C NOT FOR ALL

E. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).

Subtask 36-11-49-010-096-A ** ON A/C NOT FOR ALL

F. Open the thrust reverser cowl doors (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR

4. Procedure
Subtask 36-11-49-020-053-A ** ON A/C NOT FOR ALL

A. Removal of the Lower High Pressure (HP) Duct
(1) If you use the APU to energize the electrical circuits, stop the APU:

For GTCP 36-300 APU (Ref. AMM D/O 49-00-00-86)
For APS 3200 APU (Ref. AMM TASK 49-00-00-860-006)
For 131-9(A) APU (Ref. AMM TASK 49-00-00-860-009).

(2) In the cockpit, on the SD bleed page:
(a) Make sure that the pressure and the temperature of the bleed-air duct system are in ambient conditions.

WARNING: MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

(3) Remove the coupling (10) and the E-seal (5) that connect the lower HP duct (15) to the HP tee duct.
(4) Disconnect the muscle pressure tube from the lower HP duct (15).
(5) Put COVER - PROTECTION on the muscle pressure tube and the fitting on the lower HP duct (15).
(6) Remove the bolts (20) and the E-seals (25), at two places, that connect the lower HP duct (15) to the engine ports.
(7) Remove the lower HP duct (15) from the engine.
(8) Put PLUG - BLANKING on the engine ports, the HP tee duct, and the lower HP duct (15).

[Rev.10 from 2021] 2026.04.01 01:10:32 UTC