DOC AIRBUS | AMM A320FInstallation of the Accent Washtable Light
TASK 33-24-12-400-805-A
Installation of the Accent Washtable Light
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 33-24-12-860-071-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-420-055-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-860-062-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 06:20:28 UTC
Installation of the Accent Washtable Light
FIN: 54LQ13 ** ON A/C NOT FOR ALL
FIN: 56LQ6 ** ON A/C NOT FOR ALL
FIN: 61LQ111 ** ON A/C NOT FOR ALL
FIN: 61LQ112 ** ON A/C NOT FOR ALL
1. Reason for the JobFIN: 56LQ6 ** ON A/C NOT FOR ALL
FIN: 61LQ111 ** ON A/C NOT FOR ALL
FIN: 61LQ112 ** ON A/C NOT FOR ALL
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20 |
| No specific | 1 | PIN - NON METALLIC |
| No specific | AR | TIE WRAP |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 33-24-00-710-001-A | Operational Test of the Lavatory Lighting LQ |
| FOR [56LQ6] (WASH TABLE LIGHT) | |
| TASK 25-45-38-400-802-A | Installation of the Wash Basin of the Space Flex Lavatory |
Wash Table LightSubtask 33-24-12-860-071-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
(2) In the SMART lavatory:
(a) FOR 61LQ*
1 Make sure that the baby nursing table is open.
2 Make sure that the service cabinet above baby nursing table is open.
Subtask 33-24-12-865-068-A ** ON A/C NOT FOR ALL (1) Make sure that the aircraft electrical circuits are energized (Ref. AMM TASK 24-41-00-861-002).
(2) In the SMART lavatory:
(a) FOR 61LQ*
1 Make sure that the baby nursing table is open.
2 Make sure that the service cabinet above baby nursing table is open.
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
Subtask 33-24-12-420-055-A ** ON A/C NOT FOR ALL
A. Install the Wash Table Light in the Spaceflex Lavatory
(1) Put the wash table light (5) in position and push it until all the clamps (6) engage.
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(4) Put the cable (2) in position and install the new TIE WRAP(S) (3).
(5) Install the passenger service unit (1) and the screws (7).
Subtask 33-24-12-420-060-A ** ON A/C NOT FOR ALL (1) Put the wash table light (5) in position and push it until all the clamps (6) engage.
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
CAUTION:
REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU CONNECT THE ELECTRICAL WIRES.
INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(3) Connect the electrical connector (4). (4) Put the cable (2) in position and install the new TIE WRAP(S) (3).
(5) Install the passenger service unit (1) and the screws (7).
B. Install the Wash Table Light in the SMART Lavatory
(1) Put the wash table light (4) in position and push it until all the clamps (7) engage.
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(4) Put the terminal block (2) and the brackets (11) in the correct position on the lavatory wall and install the washers (10) and the screws (9).
(5) Put the cable (8) in position and install the new TIE WRAP(S) (3).
(6) Hold the cover (5) in the correct position and install the quick-release fasteners (6) with the PIN - NON METALLIC.
Subtask 33-24-12-410-055-A ** ON A/C NOT FOR ALL (1) Put the wash table light (4) in position and push it until all the clamps (7) engage.
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
CAUTION:
REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU CONNECT THE ELECTRICAL WIRES.
INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(3) Connect the electrical contacts (1) to the terminal block (2), use the ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20. (4) Put the terminal block (2) and the brackets (11) in the correct position on the lavatory wall and install the washers (10) and the screws (9).
(5) Put the cable (8) in position and install the new TIE WRAP(S) (3).
(6) Hold the cover (5) in the correct position and install the quick-release fasteners (6) with the PIN - NON METALLIC.
C. Close Access
(1) Close Access to the Wash Table Light in the Spaceflex lavatory:
(2) FOR [56LQ6] (WASH TABLE LIGHT)
(a) Install the wash basin (if necessary) (Ref. AMM TASK 25-45-38-400-802).
Subtask 33-24-12-410-056-A ** ON A/C NOT FOR ALL (1) Close Access to the Wash Table Light in the Spaceflex lavatory:
(2) FOR [56LQ6] (WASH TABLE LIGHT)
(a) Install the wash basin (if necessary) (Ref. AMM TASK 25-45-38-400-802).
D. Close Access
(1) Close Access to the Wash Table Light in the SMART lavatory:
(a) FOR 61LQ*
1 Close the baby nursing table.
2 Close the service cabinet above the baby nursing table.
Subtask 33-24-12-865-069-A ** ON A/C NOT FOR ALL (1) Close Access to the Wash Table Light in the SMART lavatory:
(a) FOR 61LQ*
1 Close the baby nursing table.
2 Close the service cabinet above the baby nursing table.
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 33-24-12-710-055-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
F. Operational Test
(1) Do the operational test of the lavatory lighting (Ref. AMM TASK 33-24-00-710-001).
5. Close-up(1) Do the operational test of the lavatory lighting (Ref. AMM TASK 33-24-00-710-001).
Subtask 33-24-12-860-062-A ** ON A/C NOT FOR ALL
A. Put the aircraft back to its initial configuration.
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).