Removal of the Nacelle Anti-Ice Core-Pressure-Transducer

TASK 30-21-22-000-801-A
Removal of the Nacelle Anti-Ice Core-Pressure-Transducer

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.

ZONE: 454
ZONE: 464
FIN: 4003DN ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	1	CAP - BLANKING
No specific	1	CAP - PROTECTION
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
454	HOT SECTION
464	HOT SECTION
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 30-21-12-000-801-A	Removal of the Nacelle Anti-Ice Sense-Tubes
TASK 71-00-00-860-832-A	Procedure to Prevent Engine Motoring and to Stop the Electrical Supply to the EEC
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
Nacelle Anti-Ice Core Pressure Transducer

3. Job Set-up
Subtask 30-21-22-861-050-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 30-21-22-941-050-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Do the procedure to prevent engine motoring and to stop the electrical supply to the Electronic Engine Control (EEC)
(Ref. AMM TASK 71-00-00-860-832).

Subtask 30-21-22-865-050-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
122VU	ANTI ICE/ENG/2	1DN2	W10
122VU	ANTI ICE/ENG/1	1DN1	X10

Subtask 30-21-22-010-050-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR

Subtask 30-21-22-040-050-A ** ON A/C NOT FOR ALL

E. Deactivation of the Thrust Reverser for Maintenance

WARNING: MAKE SURE THAT YOU DO THE DEACTIVATION OF THE THRUST REVERSER BEFORE YOU DO MAINTENANCE WORK ON OR AROUND THE THRUST REVERSER. IF YOU DO NOT DO THIS PROCEDURE, THERE IS A RISK OF UNWANTED OPERATION AND THUS OF INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.

(1) Do the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 30-21-22-010-051-A ** ON A/C NOT FOR ALL

F. Get Access
(1) Open the right thrust reverser cowl-door (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
462AR
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.

4. Procedure

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

CAUTION: USE TEFLON-JAWED PLIERS TO LOOSEN/TIGHTEN ELECTRICAL CONNECTORS. DO NOT USE METAL-JAWED PLIERS. IF YOU DO NOT OBEY THIS INSTRUCTION, DAMAGE TO THE ELECTRICAL CONNECTORS CAN OCCUR.

Subtask 30-21-22-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the Nacelle Anti-Ice Core-Pressure-Transducer (4003DN)
(1) Disconnect the transducer harness connector (4003DN-A) from the transducer (1) (4003DN).
(2) Put a CAP - BLANKING on the transducer harness.
(3) Disconnection of the forward transducer sense-tube:

CAUTION: USE A SECOND WRENCH TO HOLD THE MATING PARTS WHEN YOU LOOSEN OR TIGHTEN THE TUBE OR HOSE NUTS. IF YOU DO NOT OBEY THIS CAUTION, YOU CAN TWIST OR CAUSE DAMAGE TO THE TUBES OR HOSES.

(a) Disconnect the forward transducer sense-tube from the transducer (1) (Ref. AMM TASK 30-21-12-000-801).
(b) Install a CAP - PROTECTION on the forward transducer sense-tube and transducer (1).
(4) Remove the two bolts (3) and two washers (2) that hold the transducer (1) to the engine bracket.
(5) Remove the transducer (1) from the engine.

[Rev.10 from 2021] 2026.04.01 00:29:13 UTC