Apply Temporary Protection to End-Fittings of Electrical Conduits in Wing Outboard Trailing Edge

TASK 24-92-00-210-006-A
Apply Temporary Protection to End-Fittings of Electrical Conduits in Wing Outboard Trailing Edge

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 575
ZONE: 675

1. Reason for the Job
Refer to the MPD TASK: 240000-07
APPLY TEMPORARY PROTECTION TO END FITTINGS OF ELECTRICAL CONDUITS IN WING OUTBOARD TRAILING EDGE
Apply temporary protection to end fittings of electrical conduits in wing outboard trailing-edge.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	BRUSH - BRISTLED
No specific	AR	SPRAY - BOTTLE, PUMP TYPE (NON AEROSOL)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ACB1)	Corrosion Preventive Compound-Heavy Duty Hard Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
575	AFT OUTBD SE OF WING AND TE FIXED STRUCT
675	AFT OUTBD SE OF WING AND TE FIXED STRUCT
575BB, 575CB, 575DB, 575EB, 575FB, 575GB, 575HB, 575KB, 575LB, 575MB, 675BB, 675CB, 675DB, 675EB, 675FB, 675GB, 675HB, 675KB, 675LB, 675MB

D. Referenced Information

REFERENCE	DESIGNATION
TASK 12-34-24-869-002-A	Aircraft Grounding (Earthing) for the Maintenance Operations
TASK 12-34-24-869-002-A-01	Aircraft Grounding (Earthing) during Transit, Turnaround or Overnight Stop
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 27-50-00-866-008-A	Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01	Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A	Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01	Retraction of the Flaps/Slats on the Ground
TASK 27-60-00-866-002-A	Extension-Retraction of the Spoilers for Maintenance
TASK 57-51-37-000-004-A	Removal of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
TASK 57-51-37-000-005-A	Removal of the Access Panels 575KB(675KB), 575LB(675LB), 575MB(675MB)
TASK 57-51-37-400-004-A	Installation of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
TASK 57-51-37-400-005-A	Installation of the Access Panels 575KB(675KB), 575LB(675LB), 575MB(675MB)
ESPM 203330
Location of Conduit Fittings
Electrical Harness Conduits - Corrosion Protection ** ON A/C NOT FOR ALL
Typical Fittings
Location of Conduit Fittings ** ON A/C NOT FOR ALL
Electrical Harness Conduits - Corrosion Protection ** ON A/C NOT FOR ALL
Location of Conduit Fittings ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 24-92-00-860-061-A

A. Aircraft Maintenance Configuration
(1) Extend the flaps (Ref. AMM TASK 27-50-00-866-008).
(2) Extend the spoilers (Ref. AMM TASK 27-60-00-866-002).

Subtask 24-92-00-862-055-A

B. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

Subtask 24-92-00-869-061-A

C. Connect the aircraft to the ground (Ref. AMM TASK 12-34-24-869-002).

Subtask 24-92-00-010-055-A

D. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position at the wing outboard trealing-edge.
(2) For the left wing.
(a) Remove and retain the access panel:

(3) For the right wing.
(a) Remove and retain the access panel:

4. Procedure
Subtask 24-92-00-210-055-A

A. Temporary Protection of the Electrical Conduits End-Fittings in the Wing Outboard Trailing-Edge

WARNING: BE CAREFUL NOT TO CUT YOUR FINGERS. FLAKES OF NICKEL ARE SHARP.

(1) At each fitting, use the procedure that follows to protect against corrosion:
(a) Use Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) to remove any contamination from the fitting.
(b) Remove any flakes or blisters, make sure that the you do not damage the base metal while you do this task.

NOTE: We recommend that you use a dental tool or a seal tool (non metallic) to remove the flakes and the blisters.

(c) Use a BRUSH - BRISTLED or an SPRAY - BOTTLE, PUMP TYPE (NON AEROSOL) to apply a continuous thin and smooth coat of Corrosion Preventive Compound-Heavy Duty Hard Film - (Material No.12ACB1) , to cover all the fitting ESPM 203330.

5. Close-up
Subtask 24-92-00-410-056-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For the left wing.
(a) Install the access panel:

(3) For the right wing.
(a) Install the access panel:

Subtask 24-92-00-860-062-A

B. Put the aircraft back to its initial configuration.
(1) Disconnect the aircraft from the ground (Ref. AMM TASK 12-34-24-869-002).
(2) Retract the spoilers (Ref. AMM TASK 27-60-00-866-002).
(3) Retract the flaps (Ref. AMM TASK 27-50-00-866-009).
(4) Remove the access platform(s).

[Rev.10 from 2021] 2026.03.31 23:25:44 UTC