Functional Test of the Magnetic Chip Collectors [PW11]

TASK 79-22-01-720-801-A
Functional Test of the Magnetic Chip Collectors

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: WAIT FIVE MINUTES MINIMUM TO MAKE SURE THAT THE OIL SYSTEM IS NOT PRESSURIZED BEFORE YOU DO THIS PROCEDURE. IF YOU DO NOT OBEY THIS WARNING, INJURY CAN OCCUR.

ZONE: 400

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M(3 FT)
No specific	1	CARBON STEEL BALL 1 IN (25.4 MM)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-860-833-A	Procedure to Prevent Engine Motoring
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-802-A	Closing of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-805-A	Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
TASK 78-36-00-410-802-A	Closing of the Thrust Reverser Cowl-Doors
TASK 79-22-01-000-801-A	Removal and Inspection of the Magnetic Chip Collector Assemblies
TASK 79-22-01-400-801-A	Installation of the Magnetic Chip Collector Assemblies

3. Job Set-up
Subtask 79-22-01-941-052-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Do the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).

Subtask 79-22-01-010-054-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR.
(2) Put the ACCESS PLATFORM 1M(3 FT) in position.

Subtask 79-22-01-040-052-A ** ON A/C NOT FOR ALL

C. Deactivation of the Thrust Reverser for Ground Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for ground maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 79-22-01-010-055-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL, 452AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL, 462AR.

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 79-22-01-720-051-A ** ON A/C NOT FOR ALL

A. Functional Test of the Magnetic Chip Collectors
(1) Remove each chip collector probe (Ref. AMM TASK 79-22-01-000-801).
(2) Test each chip collector probe as follows:
(a) Use each chip collector probe to lift the CARBON STEEL BALL 1 IN (25.4 MM) or equivalent material and weight.

NOTE: The ball is anticipated to be available during maintenance visits and/or shop visits. If the ball is not available, you can perform the method described in step 4.A.(2)(b).

(b) Hang the magnetic probe on a horizontal steel surface so that the magnet has to fully support the weight of the probe. This is not the preferred strength test but it may be used at stations that do not have the CARBON STEEL BALL 1 IN (25.4 MM) required to perform the method described in step 4.A.(2)(a).
(c) If any of the probes do not operate correctly, replace the magnetic chip collector assembly (Ref. AMM TASK 79-22-01-000-801) and (Ref. AMM TASK 79-22-01-400-801).
(3) Install each chip collector probe again (Ref. AMM TASK 79-22-01-400-801).

5. Close-up
Subtask 79-22-01-410-051-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL, 452AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL, 462AR.

Subtask 79-22-01-440-051-A ** ON A/C NOT FOR ALL

B. Do the reactivation of the thrust reverser system after ground maintenance (Ref. AMM TASK 78-30-00-440-805).

Subtask 79-22-01-410-052-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR.
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 03:42:00 UTC