DOC AIRBUS | AMM A320FSpecial Detailed Inspection (Endoscope) of Aft Engine Mount Pins [CFMI]
TASK 71-22-11-210-802-A
Special Detailed Inspection (Endoscope) of Aft Engine Mount Pins
Refer to the MPD TASK: 712213-01
SPECIAL DETAILED INSPECTION (ENDOSCOPE) OF AFT ENGINE MOUNT PINS
This inspection criterion is only for those parts of the engine that you can see when the engine is installed on an aircraft. The limits and remarks are not applicable to the areas of the mount that you cannot see when the engine is installed.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Expendable Parts
E. Referenced Information
3. Job Set-up
Subtask 71-22-11-860-054-A ** ON A/C NOT FOR ALL
Subtask 71-22-11-280-055-A ** ON A/C NOT FOR ALL
PRE SB RA32071-164
PRE SB RA32071-174
(1) Removal of one shear bolt at the cross beam attachment:
(a) Remove the retaining pin (135) from the shear pin (145).
(b) Remove the nuts (120), washers (115), bolts (105) and washers (110).
(c) Remove the retainers (125), (130) and (155) and the nut (160) from the engine.
(d) Remove the anti-rotation bracket (150), shear pin (145) and shear bolt (140).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X.
1 Clean any dirt or unwanted material from the shear bolt (140) and the inner surface of the shear pin (145) with isopropyl alcohol (Material No.CP1041) .
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (140) and the inner surface of the shear pin (145) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt at the cross beam attachment:
(a) Visually examine the bracket (150), retainers (125), (130) and (155) and nuts (160) and (165) for indication of damage. If there are scratches, marks and/or damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (140).
(c) Install the shear bolt (140) into the shear pin (145).
(d) Install the nuts (165).
(e) TORQUE the nuts to the minimum value of to between 42 and 35 lbf.ft (5.69 and 4.75 m.daN )
.
(g) When the nut (165) is torqued and in the aligned position, install the outer retainers (125), (130) and (155), nut (160) with the bolts (105), washers (110), and (115) and nuts (120).
(h) TORQUE the nuts (120) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (150), shear pin (145), bolt (140) and retaining pin (135).
(4) Do steps 4.B.(1) to (3) again for the other two shear bolts and shear pins.
END OF PRE SB RA32071-164
END OF PRE SB RA32071-174
Subtask 71-22-11-280-057-A ** ON A/C NOT FOR ALL
POST SB RA32071-164
(1) Removal of the shear bolt from the left hand link:
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (73), (63) and (103) and the nut (90) from the engine.
(d) Remove the bracket (140) and the shear pin (130).
(e) Remove and discard the lock nut (81) from the shear bolt (120).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt on the left hand link:
(a) Visually examine the bracket (140) and the retainers (73), (63) and (103) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66.00 lbf.ft (9.63 and 8.95 m.daN ).
(g) When the lock nut (81) is torqued and in the aligned position, install the retainers (73), (63) and (103) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (140), shear pin (130), shear bolt (120) and retaining pin (110).
Subtask 71-22-11-280-058-A ** ON A/C NOT FOR ALL
POST SB RA32071-174
(1) Removal of the shear bolt from the left hand link:
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (74), (64) and (104) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt on the left hand link:
(a) Visually examine the bracket (140), retainers (74), (64) and (104) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN ).
(g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (74), (64) and (104) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (140), shear pin (130), bolt (120) and retaining pin (110).
Subtask 71-22-11-280-061-A ** ON A/C NOT FOR ALL
Subtask 71-22-11-410-080-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 02:23:00 UTC
Special Detailed Inspection (Endoscope) of Aft Engine Mount Pins
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 400
1. Reason for the JobRefer to the MPD TASK: 712213-01
SPECIAL DETAILED INSPECTION (ENDOSCOPE) OF AFT ENGINE MOUNT PINS
This inspection criterion is only for those parts of the engine that you can see when the engine is installed on an aircraft. The limits and remarks are not applicable to the areas of the mount that you cannot see when the engine is installed.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 1M(3 FT) |
| No specific | 1 | BORESCOPE - FLEXIBLE |
| No specific | 8 | FLASHLIGHT |
| No specific | 1 | MAGNIFYING GLASS POWER 10X |
| No specific | AR | WARNING NOTICE(S) |
| No specific | Torque wrench: range to between 42 and 35 lbf.ft (5.69 and 4.75 m.daN ) | |
| No specific | Torque wrench: range to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN ) | |
| No specific | Torque wrench: range to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ) | |
| 98D27803500001 | 1 | LOCKING TOOL ZERO POS |
| RSE1098 | 1 | WRENCH SET - AFT ENGINE MOUNT |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.CP1041) | isopropyl alcohol |
| (Material No.CP5063) | silicone lubricant |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 400 | POWER PLANT, NACELLES AND PYLONS |
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR, 451AL, 452AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR, 461AL, 462AR | |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 81 | NUT | AIPC 71-22-11-01-080 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 20-21-11-911-001-A | Tightening Torques for Standard Threaded Fasteners |
| TASK 71-13-00-010-040-A | Opening of the Fan Cowl Doors |
| TASK 71-13-00-410-040-A | Closing of the Fan Cowl Doors |
| TASK 71-22-11-000-040-A | Removal of the Aft Engine Mount |
| TASK 71-22-11-000-042-A | Removal of the Aft Engine Mount without Engine Removal |
| TASK 71-22-11-400-040-A | Installation of the Aft Engine Mount |
| TASK 71-22-11-400-042-A | Installation of the Aft Engine Mount without Engine Removal |
| TASK 78-30-00-081-041-A | Make the Thrust Reverser Serviceable after Maintenance |
| TASK 78-30-00-481-041-A | Make the Thrust Reverser Unserviceable for Maintenance |
| TASK 78-36-00-010-040-A | Opening of the Thrust Reverser Doors |
| TASK 78-36-00-410-040-A | Closing of the Thrust Reverser Doors |
Aft Engine Mount PinsSubtask 71-22-11-860-054-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.
(4) Make sure that the slats are retracted and install 98D27803500001 LOCKING TOOL ZERO POS on the flap and slat control lever.
Subtask 71-22-11-010-079-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.
(4) Make sure that the slats are retracted and install 98D27803500001 LOCKING TOOL ZERO POS on the flap and slat control lever.
B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(2) FOR [1000EM1] (ENGINE-1)
437AL, 438AR
(3) FOR [1000EM2] (ENGINE-2)
447AL, 448AR.
Subtask 71-22-11-040-062-A ** ON A/C NOT FOR ALL Subtask 71-22-11-010-111-A ** ON A/C NOT FOR ALL (1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(2) FOR [1000EM1] (ENGINE-1)
437AL, 438AR
(3) FOR [1000EM2] (ENGINE-2)
447AL, 448AR.
D. Make sure that the thrust reverser doors are open (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL, 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL, 462AR.
4. Procedure(1) FOR [1000EM1] (ENGINE-1)
451AL, 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL, 462AR.
Subtask 71-22-11-280-055-A ** ON A/C NOT FOR ALL
A. Special Detailed Inspection (Endoscope) of the Shear Bolt and Shear Pin
(a) Remove the retaining pin (85) from the shear pin (45).
(b) Remove the bolts (5), washers (10) and (15) and nuts (20) which attach the outer retainers (25) and (30) to the bracket (60).
(c) Remove the outer retainers (25) and (30) from the engine.
(d) Remove the slotted spanner nut (35) from the shear bolt (50).
(e) Remove the shear bolt (50).
1 If you cannot remove the shear bolt (50), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and shear pin.
(a) Do a special detailed inspection of the shear bolt and shear pin, with BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and a MAGNIFYING GLASS POWER 10X.
1 Clean any dirt or unwanted material from the shear bolt (50) and the inner surface of the shear pin (45) with isopropyl alcohol (Material No.CP1041) .
a Do a visual inspection of the shear pin (outer and inner surface of the pin) and bolt bore for unusual step(s), groove(s), unusual machining marks and sign of damage. Use FLASHLIGHT if needed.
The inner and outer surface should be a smooth,constant machined diameter where no disruption is witnessed. If any of these defects are found parts must be discarded and replaced.
2 Examine the shear bolt (50) and the inner surface of the shear pin (45) for cracks. No cracks are permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt at the turbine case attachment.
(b) Apply silicone lubricant (Material No.CP5063) to the threads of the shear bolt (50).
(c) Install the shear bolt (50) into the shear pin (45).
(d) Install the slotted spanner.
1 TORQUE the nut (35) to between 42 and 35 lbf.ft (5.69 and 4.75 m.daN ).
2 Use the RSE1098 WRENCH SET - AFT ENGINE MOUNT to adapt the torque wrench to the spanner nut (35).
(g) If the holes in the anti-rotation bracket (25) do not line up with the holes in brackets (30) and (60), increase the torque on the nut (35) as necessary to line up the holes. Do not TORQUE the nut(35) more than 42 lbf.ft (5.69 m.daN).
(h) TORQUE the nuts (20) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the retaining pin (85) through the shear pin (45).
(4) Do steps 4.A.(1) to (3) again for the other two shear bolts and shear pins.
Subtask 71-22-11-280-056-A ** ON A/C NOT FOR ALL CAUTION:
ONLY CHECK ONE PIN AT A TIME.
(1) Removal of one shear bolt at the turbine case attachment. (a) Remove the retaining pin (85) from the shear pin (45).
(b) Remove the bolts (5), washers (10) and (15) and nuts (20) which attach the outer retainers (25) and (30) to the bracket (60).
(c) Remove the outer retainers (25) and (30) from the engine.
(d) Remove the slotted spanner nut (35) from the shear bolt (50).
(e) Remove the shear bolt (50).
1 If you cannot remove the shear bolt (50), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and shear pin.
(a) Do a special detailed inspection of the shear bolt and shear pin, with BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and a MAGNIFYING GLASS POWER 10X.
1 Clean any dirt or unwanted material from the shear bolt (50) and the inner surface of the shear pin (45) with isopropyl alcohol (Material No.CP1041) .
a Do a visual inspection of the shear pin (outer and inner surface of the pin) and bolt bore for unusual step(s), groove(s), unusual machining marks and sign of damage. Use FLASHLIGHT if needed.
The inner and outer surface should be a smooth,constant machined diameter where no disruption is witnessed. If any of these defects are found parts must be discarded and replaced.
2 Examine the shear bolt (50) and the inner surface of the shear pin (45) for cracks. No cracks are permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt at the turbine case attachment.
CAUTION:
USE OF THE SPANNER WRENCHES AS A TORQUE WRENCH ADAPTER WILL CHANGE THE TORQUE VALUE WHICH IS REALLY APPLIED. THE EFFECTIVE LENGTH OF THE SPANNER WRENCHES ARE:
RSE1098-1 : 6-INCHES (152.4 MM)
RSE1098-5 : 8-INCHES (203.2 MM)
(a) Visually examine the retainers (25) and (30) and nut (35) for indication of damage. If there are scratches, marks and/or other damage, reject the parts. (b) Apply silicone lubricant (Material No.CP5063) to the threads of the shear bolt (50).
(c) Install the shear bolt (50) into the shear pin (45).
(d) Install the slotted spanner.
NOTE: To find the correct torque value when spanner wrenches are used, refer to the formula in the standard practices (Ref. AMM TASK 20-21-11-911-001).
(e) Install the slotted spanner nut (35) on the shear bolt (50). 1 TORQUE the nut (35) to between 42 and 35 lbf.ft (5.69 and 4.75 m.daN )
. 2 Use the RSE1098 WRENCH SET - AFT ENGINE MOUNT to adapt the torque wrench to the spanner nut (35).
NOTE: It is recommended that you position the flat side of the nut (35) forward.
(f) Install the outer retainers (25) and (30) on the bracket (60) with washers (10) below bolts (5) and washers (15) below nuts (20). (g) If the holes in the anti-rotation bracket (25) do not line up with the holes in brackets (30) and (60), increase the torque on the nut (35) as necessary to line up the holes. Do not TORQUE the nut(35) more than 42 lbf.ft (5.69 m.daN).
(h) TORQUE the nuts (20) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
. (i) Install the retaining pin (85) through the shear pin (45).
(4) Do steps 4.A.(1) to (3) again for the other two shear bolts and shear pins.
CAUTION:
ONLY CHECK ONE PIN AT A TIME.
B. Special Detailed Inspection (Endoscope) of the Shear Bolt at the Cross Beam Attachment PRE SB RA32071-164
PRE SB RA32071-174
(1) Removal of one shear bolt at the cross beam attachment:
(a) Remove the retaining pin (135) from the shear pin (145).
(b) Remove the nuts (120), washers (115), bolts (105) and washers (110).
(c) Remove the retainers (125), (130) and (155) and the nut (160) from the engine.
(d) Remove the anti-rotation bracket (150), shear pin (145) and shear bolt (140).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X.
1 Clean any dirt or unwanted material from the shear bolt (140) and the inner surface of the shear pin (145) with isopropyl alcohol (Material No.CP1041) .
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (140) and the inner surface of the shear pin (145) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt at the cross beam attachment:
(a) Visually examine the bracket (150), retainers (125), (130) and (155) and nuts (160) and (165) for indication of damage. If there are scratches, marks and/or damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (140).
(c) Install the shear bolt (140) into the shear pin (145).
(d) Install the nuts (165).
(e) TORQUE the nuts to the minimum value of to between 42 and 35 lbf.ft (5.69 and 4.75 m.daN )
. NOTE: TORQUE the nuts (165) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (73).
(f) Temporarily install the anti-rotation retainers (125) and record the position necessary for the alignment of the nuts. Increase the torque on the nuts (165) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (125). (g) When the nut (165) is torqued and in the aligned position, install the outer retainers (125), (130) and (155), nut (160) with the bolts (105), washers (110), and (115) and nuts (120).
(h) TORQUE the nuts (120) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
. (i) Install the anti-rotation bracket (150), shear pin (145), bolt (140) and retaining pin (135).
(4) Do steps 4.B.(1) to (3) again for the other two shear bolts and shear pins.
END OF PRE SB RA32071-164
END OF PRE SB RA32071-174
CAUTION:
ONLY CHECK ONE PIN AT A TIME.
C. Special Detailed Inspection (Endoscope) of the Shear Bolt of the Left Hand Link POST SB RA32071-164
(1) Removal of the shear bolt from the left hand link:
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (73), (63) and (103) and the nut (90) from the engine.
(d) Remove the bracket (140) and the shear pin (130).
(e) Remove and discard the lock nut (81) from the shear bolt (120).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt on the left hand link:
(a) Visually examine the bracket (140) and the retainers (73), (63) and (103) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66.00 lbf.ft (9.63 and 8.95 m.daN )
. NOTE: TORQUE the lock nuts (81) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (73).
(f) Temporarily install the anti-rotation retainers (73) and record the position necessary for the alignment of the nuts. Increase the torque on the lock nuts (81) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (73). (g) When the lock nut (81) is torqued and in the aligned position, install the retainers (73), (63) and (103) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
. (i) Install the anti-rotation bracket (140), shear pin (130), shear bolt (120) and retaining pin (110).
D. Special Detailed Inspection (Endoscope) of the Shear Bolt of the Right Hand Link
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (75), (65) and (105) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Install the shear bolt on the right hand link:
(a) Visually examine the bracket (140), retainers (75), (65) and (105) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66.00 lbf.ft (9.63 and 8.95 m.daN ).
(g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (75), (65) and (105) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (140), shear pin (130), shear bolt (120) and retaining pin (110).
Subtask 71-22-11-280-059-A ** ON A/C NOT FOR ALL CAUTION:
ONLY CHECK ONE PIN AT A TIME.
(1) Removal of the shear bolt from the right hand link: (a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (75), (65) and (105) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Install the shear bolt on the right hand link:
(a) Visually examine the bracket (140), retainers (75), (65) and (105) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66.00 lbf.ft (9.63 and 8.95 m.daN )
. NOTE: TORQUE the lock nuts (81) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (75).
(f) Temporarily install the anti-rotation retainers (75) and record the position necessary for the alignment of the nuts. Increase the torque on the lock nuts (81) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (75). (g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (75), (65) and (105) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
. (i) Install the anti-rotation bracket (140), shear pin (130), shear bolt (120) and retaining pin (110).
E. Special Detailed Inspection (Endoscope) of the Shear Bolt of the Center Link
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (75), (65) and (105) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Install the shear bolt on the center link:
(a) Visually examine the bracket (140), retainers (75), (65) and (105) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66.00 lbf.ft (9.63 and 8.95 m.daN ).
(g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (75), (65) and (105) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (140), shear pin (130), shear bolt (120) and retaining pin (110).
END OF POST SB RA32071-164
Subtask 71-22-11-280-060-A ** ON A/C NOT FOR ALL CAUTION:
ONLY CHECK ONE PIN AT A TIME.
(1) Remove the shear bolt from the center link: (a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (75), (65) and (105) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Install the shear bolt on the center link:
(a) Visually examine the bracket (140), retainers (75), (65) and (105) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66.00 lbf.ft (9.63 and 8.95 m.daN )
. NOTE: TORQUE the lock nuts (81) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (75).
(f) Temporarily install the anti-rotation retainers (75) and record the position necessary for the alignment of the nuts. Increase the torque on the lock nuts (81) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (75). (g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (75), (65) and (105) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
. (i) Install the anti-rotation bracket (140), shear pin (130), shear bolt (120) and retaining pin (110).
END OF POST SB RA32071-164
CAUTION:
ONLY CHECK ONE PIN AT A TIME.
F. Special Detailed Inspection (Endoscope) of the Shear Bolt of the Left Hand Link for the Four Lug Turbine Case ConfigurationPOST SB RA32071-174
(1) Removal of the shear bolt from the left hand link:
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (74), (64) and (104) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary.
The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt on the left hand link:
(a) Visually examine the bracket (140), retainers (74), (64) and (104) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN )
.NOTE: TORQUE the lock nuts (81) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (74).
(f) Temporarily install the anti-rotation retainers (74) and record the position necessary for the alignment of the nuts. Increase the torque on the lock nuts (81) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (74). (g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (74), (64) and (104) and the nut (90) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
.(i) Install the anti-rotation bracket (140), shear pin (130), bolt (120) and retaining pin (110).
G. Special Detailed Inspection (Endoscope) of the Shear Bolt of the Right Hand Link for the Four Lug Turbine Case Configuration
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (76), (66) and (106) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary. The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt on the right hand link:
(a) Visually examine the bracket (140), retainers (76), (66) and (106) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN ).
(g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (76), (66), and (106) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (140), shear pin (130), bolt (120) and retaining pin (110).
Subtask 71-22-11-280-062-A ** ON A/C NOT FOR ALL CAUTION:
ONLY CHECK ONE PIN AT A TIME.
(1) Removal the shear bolt from the right hand link:(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (76), (66) and (106) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) :
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary. The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Installation of the shear bolt on the right hand link:
(a) Visually examine the bracket (140), retainers (76), (66) and (106) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) on the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN )
.NOTE: TORQUE the lock nuts (81) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (76).
(f) Temporarily install the anti-rotation retainers (76) and record the position necessary for the alignment of the nuts. Increase the torque on the lock nuts (81) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (76). (g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (76), (66), and (106) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
.(i) Install the anti-rotation bracket (140), shear pin (130), bolt (120) and retaining pin (110).
H. Special Detailed Inspection (Endoscope) of the Shear Bolt of the Center Link for the Four Lug Turbine Case Configuration
(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (77), (67) and (107) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) .
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary. The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Install the shear bolt on the center link:
(a) Visually examine the bracket (140), retainers (77), (67) and (107) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) to the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN ).
(g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (77), (67) and (107) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN ).
(i) Install the anti-rotation bracket (140), shear pin (130), bolt (120) and retaining pin (110).
END OF POST SB RA32071-174
5. Close-upCAUTION:
ONLY CHECK ONE PIN AT A TIME.
(1) Removal of the shear bolt from the center link:(a) Remove the retaining pin (110) from the shear pin (130).
(b) Remove the nuts (50), washers (45) and bolts (20).
(c) Remove the retainers (77), (67) and (107) and the nut (90) from the engine.
(d) Remove and discard the lock nut (81) from the shear bolt (120).
(e) Remove the bracket (140) and the shear pin (130).
(f) Remove the shear bolt (120):
1 If you cannot remove the shear bolt (120), replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(2) Special detailed inspection (endoscope) of the shear bolt and the shear pin:
(a) Do the special detailed inspection of the shear bolt and the shear pin with the BORESCOPE - FLEXIBLE dia. up to 5 mm (0.1969 in.) and the MAGNIFYING GLASS POWER 10X:
1 Clean any dirt or unwanted material from the shear bolt (120) and the inner surface of the shear pin (130) with isopropyl alcohol (Material No.CP1041) .
a Do the visual inspection of the shear pin (outer and inner surfaces of the pin) and the bolt bore for unusual step(s), groove(s), unusual machining marks and signs of damage. Use the FLASHLIGHT, if necessary. The inner and outer surfaces must be a smooth, constant machined diameter where no disruption is witnessed. If you find any of these defects, discard and replace the parts.
2 Examine the shear bolt (120) and the inner surface of the shear pin (130) for cracks. Cracks are not permitted. If cracks are found, replace the mount (Ref. AMM TASK 71-22-11-000-040) and (Ref. AMM TASK 71-22-11-400-040) or (Ref. AMM TASK 71-22-11-000-042) and (Ref. AMM TASK 71-22-11-400-042).
(3) Install the shear bolt on the center link:
(a) Visually examine the bracket (140), retainers (77), (67) and (107) and nut (90) for indication of damage. If there are scratches, marks and/or other damage, reject the parts.
(b) Apply silicone lubricant (Material No.CP5063) to the threads of the shear bolt (120).
(c) Install the shear bolt (120) into the shear pin (130).
(d) Install the new AIPC 71-22-11-01-080 NUT (81).
(e) TORQUE the lock nuts (81) to the minimum value of to between 71.02 and 66 lbf.ft (9.63 and 8.95 m.daN )
.NOTE: TORQUE the lock nuts (81) to the minimum value. When the retainers are installed, increase the value as necessary to align the nuts with the anti-rotation retainers (77).
(f) Temporarily install the anti-rotation retainers (77) and record the position necessary for the alignment of the nuts. Increase the torque on the lock nuts (81) as necessary (do not torque more than the maximum torque value), to align the nuts with the retainers (77).(g) When the lock nuts (81) are torqued and in the aligned position, install the retainers (77), (67) and (107) with the bolts (20), washers (45) and nuts (50).
(h) TORQUE the nuts (50) to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
.(i) Install the anti-rotation bracket (140), shear pin (130), bolt (120) and retaining pin (110).
END OF POST SB RA32071-174
Subtask 71-22-11-410-080-A ** ON A/C NOT FOR ALL
A. Close the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-410-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL, 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL, 462AR.
Subtask 71-22-11-440-060-A ** ON A/C NOT FOR ALL Subtask 71-22-11-410-081-A ** ON A/C NOT FOR ALL (1) FOR [1000EM1] (ENGINE-1)
451AL, 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL, 462AR.
C. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(3) FOR [1000EM1] (ENGINE-1)
437AL, 438AR
(4) FOR [1000EM2] (ENGINE-2)
447AL, 448AR.
(5) Remove the WARNING NOTICE(S).
(6) On panel 114VU, remove the locking tool from the flap and slat control lever.
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(3) FOR [1000EM1] (ENGINE-1)
437AL, 438AR
(4) FOR [1000EM2] (ENGINE-2)
447AL, 448AR.
(5) Remove the WARNING NOTICE(S).
(6) On panel 114VU, remove the locking tool from the flap and slat control lever.