Partial Removal of the Exhaust Muffler for Inspection (APS 3200)

TASK 49-81-41-000-803-A
Partial Removal of the Exhaust Muffler for Inspection (APS 3200)

WARNING: DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

1. Reason for the Job
To get access to the APU rear housing for an inspection for oil leaks
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
315AL, 316AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 52-41-00-010-001-A	Open the APU Doors for Access
TASK 52-41-18-000-001-A	Removal of the APU Exhaust Access-Fairing
Exhaust Muffler

3. Job Set-up
Subtask 49-81-41-860-062-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) On panel 25VU, make sure that the APU MASTER SW pushbutton switch is released (ON legend off).
(3) Put a WARNING NOTICE(S) in position in the cockpit to tell persons not to start the APU.
(4) Make sure that the hydraulic systems are depressurized
(Ref. AMM TASK 29-00-00-864-001).

Subtask 49-81-41-865-062-A ** ON A/C NOT FOR ALL

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

Subtask 49-81-41-010-055-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Put an ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE below APU access doors 315AL and 316AR.
(2) Open APU access doors 315AL and 316AR (Ref. AMM TASK 52-41-00-010-001).
(3) Set the LIGHT control switch 11LJ to the ON position.
(4) Remove the APU exhaust access-fairing (Ref. AMM TASK 52-41-18-000-001).

4. Procedure
Subtask 49-81-41-020-054-A ** ON A/C NOT FOR ALL

A. Partial Removal of the Exhaust Muffler for Inspection
(1) Loosen the nut (14) and disconnect the drain line (13).
(2) Remove and discard the lockwire:

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(a) Remove and discard the lockwire from the stud fasteners of the insulation blanket forward of the bellow clamps.
(3) Remove the halves (19) and (20) of the insulation blanket.
(4) Remove the V-clamp (15) from the APU exhaust flange (16).
(5) Remove and discard the cotter pins (2) from the nuts (3) and (5).
(6) Remove the nut (5), washer (6), bolt (8) and washer (9).
(7) Remove the nut (3), washer (4), bushing (11) and bolt (12).
(8) Pull the exhaust muffler (7) a maximum distance of 2 in. (50.80 mm) from the guide rails (10).

[Rev.10 from 2021] 2026.04.01 12:41:44 UTC