Installation of the Strut 5 [CFML]

TASK 72-24-03-400-802-A
Installation of the Strut 5

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 400

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )
No specific	Torque wrench: range to between 92.4 and 83.6 lbf.in (1.04 and 0.94 m.daN )
No specific	Torque wrench: range to between 120.75 and 109.25 lbf.in (1.36 and 1.23 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.CP2101)	graphite mineral vaseline

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL, 448AR, 461AL, 462AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-803-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-803-A	Closing of the Fan Cowl Doors
TASK 78-30-00-040-809-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-809-A	Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-010-806-A	Opening of the Thrust Reverser Cowl Doors
TASK 78-36-00-410-806-A	Closing of the Thrust Reverser Cowl Doors
Strut 5

3. Job Set-up
Subtask 72-24-03-941-053-A

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Make sure that the WARNING NOTICE(S) are in position to tell persons not to operate:

The ENG/MODE selector switch, and
The ENG/MASTER 1(2) control switch.

(2) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Make sure that the WARNING NOTICE(S) is in position to tell persons not to energize FADEC 1(2).

Subtask 72-24-03-010-056-A

B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR.

Subtask 72-24-03-040-053-A

C. Deactivation of the Thrust Reverser System for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Make sure that you did the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-809).

Subtask 72-24-03-010-057-A

D. Get Access
(1) Make sure that the thrust reverser cowl doors are open (Ref. AMM TASK 78-36-00-010-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR.

4. Procedure
Subtask 72-24-03-420-051-A

A. Installation of the Strut 5
(1) Make sure that the mating surfaces are clean and clear of unwanted materials.
(2) Installation of the strut 5 pad (right) (24):
(a) Lubricate the threads of the two bolts (23) with the graphite mineral vaseline (Material No.CP2101) .
(b) Install the strut 5 pad (right) (24) in the correct position.
(c) Install the two bolts (23) to attach the strut 5 pad (right) (24) to the fan frame hub (21) and tighten them with your hand.
(d) TORQUE the two bolts (23) to between 120.75 and 109.25 lbf.in (1.36 and 1.23 m.daN )

.
(3) Installation of the strut 5 pad (left) (22):
(a) Lubricate the threads of the two bolts (20) and the bolt (19) with the graphite mineral vaseline (Material No.CP2101) .
(b) Install the strut 5 pad (left) (22) in the correct position.
(c) Install the bolt (19) to attach the strut 5 pad (left) (22) to the strut 5 pad (right) (24) and tighten it with your hand.
(d) TORQUE the bolt (19) to between 120.75 and 109.25 lbf.in (1.36 and 1.23 m.daN )

.
(e) Install the two bolts (20) to attach the strut 5 pad (left) (22) to the fan frame hub (21) and tighten them by hand.
(f) TORQUE the two bolts (20) to between 120.75 and 109.25 lbf.in (1.36 and 1.23 m.daN )

.
(4) Lubricate the threads of the bolt (18) with the graphite mineral vaseline (Material No.CP2101) .
(5) Install the nut (17) and the bolt (18) to attach the strut 5 pad (right) (24) to the strut 5 pad (left) (22) and tighten them with your hand.
(6) TORQUE the nut (17) to between 120.75 and 109.25 lbf.in (1.36 and 1.23 m.daN )

.
(7) Installation of the strut 5 fairing (left) (12):
(a) Lubricate the threads of the four screws (16), the three screws (15), the three screws (13) and the screw (14) with the graphite mineral vaseline (Material No.CP2101) .
(b) Install the strut 5 fairing (left) (12) in the correct position.
(c) Install the three screws (13) to attach the strut 5 fairing (left) (12) to the strut 5 outer fitting (11) and tighten them with your hand.
(d) TORQUE the three screws (13) to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )

.
(e) Install the three screws (15) and the screw (14) to attach the strut 5 fairing (left) (12) to the strut 5 fairing support (6) and tighten with them your hand.
(f) TORQUE the three screws (15) and the screw (14) to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )

.
(g) Install the four screws (16) to attach the strut 5 fairing (left) (12) to the strut 5 pad (left) (22) and tighten them with your hand.
(h) TORQUE the four screws (16) to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )

.
(8) Connection of the bracket (4):
(a) Lubricate the threads of the four bolts (5) with the graphite mineral vaseline (Material No.CP2101) .
(b) Install the seal (3) on the bracket (4).
(c) Install the four nuts (2) and the four bolts (5) to connect the bracket (4) to the strut 5 (1) and tighten them with your hand.
(d) TORQUE the four bolts (5) to between 92.4 and 83.6 lbf.in (1.04 and 0.94 m.daN )

.
(9) Installation of the strut 5 fairing (right) (10):
(a) Lubricate the threads of the four screws (7), the three screws (8), the three screws (9) and the screw (2) with the graphite mineral vaseline (Material No.CP2101) .
(b) Install the strut 5 fairing (right) (10) in the correct position.
(c) Install the three screws (9) to attach the strut 5 fairing (right) (10) to the strut 5 outer fitting (11) and tighten them with your hand.
(d) TORQUE the three screws (9) to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )

.
(e) Install the three screws (8) and the screw (2) to attach the strut 5 fairing (right) (10) to the strut 5 fairing support (6) and tighten them with your hand.
(f) TORQUE the three screws (8) and the screw (2) to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )

.
(g) Install the four screws (7) to attach the strut 5 fairing (right) (10) to the strut 5 pad (right) (24) and tighten them with your hand.
(h) TORQUE the four screws (7) to between 84 and 76 lbf.in (0.95 and 0.86 m.daN )

5. Close-up
Subtask 72-24-03-410-054-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser cowl doors (Ref. AMM TASK 78-36-00-410-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR.

Subtask 72-24-03-440-052-A

B. Do the reactivation of the thrust reverser system after maintenance (Ref. AMM TASK 78-30-00-440-809).

Subtask 72-24-03-410-055-A

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR.
(2) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 02:52:42 UTC