Replace the Fan Intermediate Case Assembly Helical Coil Insert(s) [PW11]

TASK 72-22-00-960-801-A
Replace the Fan Intermediate Case Assembly Helical Coil Insert(s)

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: THIS AIRCRAFT MAINTENANCE MANUAL REPAIR LETS YOU REPLACE ONLY THE ORIGINAL EQUIPMENT MANUFACTURER'S HELICAL COIL INSERT(S). IF THERE IS DAMAGE TO THE HOLE(S) AND AN OVERSIZED INSERT IS NECESSARY, THEN YOU MUST DO THE REPAIR ON-WING. YOU MUST REMOVE AND REPAIR THE PART AS PER THE APPLICABLE CLEANING, INSPECTION AND REPAIR MANUAL.

ZONE: 400

1. Reason for the Job
Use this procedure to repair loose, missing, or damaged helical coil insert(s) of the fan intermediate case assembly.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL, 462AR

C. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
1	HELICAL COIL INSERT	EIPC 72-22-01-01-100
2	HELICAL COIL INSERT	EIPC 72-22-01-01-110

D. Referenced Information

REFERENCE	DESIGNATION
TASK 70-24-00-910-803-A	SPOP 415 - Installation of Helical Coil Threaded Inserts
TASK 71-00-00-860-833-A	Procedure to Prevent Engine Motoring
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-802-A	Closing of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-805-A	Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
TASK 78-36-00-410-802-A	Closing of the Thrust Reverser Cowl-Doors
Fan Intermediate Case Assembly Helical Coil Insert(s) Location

3. Job Set-up
Subtask 72-22-00-941-052-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Do the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).

Subtask 72-22-00-010-052-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR.
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.

Subtask 72-22-00-040-051-A ** ON A/C NOT FOR ALL

C. Deactivation of the Thrust Reverser for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 72-22-00-010-053-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL, 452AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL, 462AR.

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 72-22-00-960-050-A ** ON A/C NOT FOR ALL

A. Replace the Fan Intermediate Case Assembly Helical Coil Insert(s)
(1) Remove the loose or damaged helical coil insert(s) by SPOP 415 (Ref. AMM TASK 70-24-00-910-803).
(2) Install the new EIPC 72-22-01-01-100 HELICAL COIL INSERT (1) and/or EIPC 72-22-01-01-110 HELICAL COIL INSERT (2) by SPOP 415 (Ref. AMM TASK 70-24-00-910-803). For the location and identification of helical coil insert part numbers refer to Table 801.

Fan Intermediate Case Assembly Helical Coil Insert(s) Location ** ON A/C NOT FOR ALL

Table 801 - Helical Coil Insert Part Numbers

Index Number	Part Number
(1)	NAS1130-5FL15
(2)	NAS1130-4FL15

(3) Do a visual inspection of the installed helical coil insert(s) to make sure they are installed as specified in SPOP 415 (Ref. AMM TASK 70-24-00-910-803). engine.
(4) Examine the assembly for foreign objects, damage, and correct assembly.

5. Close-up
Subtask 72-22-00-410-052-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL, 452AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL, 462AR.

Subtask 72-22-00-440-051-A ** ON A/C NOT FOR ALL

B. Do the reactivation of the thrust reverser system after maintenance (Ref. AMM TASK 78-30-00-440-805).

Subtask 72-22-00-410-053-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR.
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR.
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 02:49:09 UTC