W DOC AIRBUS | AMM A320F

Installation of the Rear Mount-Fairing Block Fire-Seal

TASK 54-57-22-400-820-A
Installation of the Rear Mount-Fairing Block Fire-Seal

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 410
ZONE: 420
FIN: 4020KM1 ** ON A/C NOT FOR ALL
FIN: 4020KM2 ** ON A/C NOT FOR ALL
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
Torque wrench: range to between 4.7 and 3.7 m.N (41.59 and 32.74 lbf.in ) T
No specific
Torque wrench: range to between 0.17 and 0.13 m.daN (15.04 and 11.50 lbf.in ) T
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
410
ENG 1 PYLON BOX AND FORWARD FAIRING
420
ENG 2 PYLON BOX AND FORWARD FAIRING
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL, 462AR
 D. Expendable Parts
FIG.ITEM
DESIGNATION
IPC-CSN
3
FIRE-SEAL
AIPC 54-51-86-07-130
3
FIRE-SEAL
AIPC 54-51-86-07-200
 E. Referenced Information
REFERENCE
DESIGNATION
TASK 54-56-11-410-801-A
Closing of the Rear Mount Fairing (RMF) Door
TASK 71-00-00-860-833-A
Procedure to Prevent Engine Motoring
TASK 71-13-00-410-802-A
Closing of the Fan Cowl Doors
TASK 78-30-00-040-805-A
Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-805-A
Reactivation of the Thrust Reverser System after Ground Maintenance
TASK 78-36-00-410-802-A
Closing of the Thrust Reverser Cowl-Doors
F Rear Mount-Fairing Block Fire-Seal
3. Job Set-up
Subtask 54-57-22-941-100-A ** ON A/C NOT FOR ALL
A. Safety Precautions
   (1) Make sure that you did the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).
   (2) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position:
     (a) For the left pylon, at zone 415
     (b) For the right pylon, at zone 425.
Subtask 54-57-22-040-088-A ** ON A/C NOT FOR ALL
B. Deactivation of the Thrust Reverser
WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.
   (1) Make sure that the thrust reverser is unserviceable for maintenance (Ref. AMM TASK 78-30-00-040-805).
Subtask 54-57-22-110-061-A ** ON A/C NOT FOR ALL
C. Preparation for Installation
   (1) Make sure that the parts retained from the removed component are clean and in the correct condition.
   (2) Clean the parts kept from the removed component with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) , if necessary.
   (3) Do an inspection of the component interfaces and the adjacent area.
4. Procedure
Subtask 54-57-22-420-082-A ** ON A/C NOT FOR ALL
A. Installation of the Rear Mount-Fairing Block Fire-Seal
F Rear Mount-Fairing Block Fire-Seal ** ON A/C NOT FOR ALL
   (1) Make sure that the rear mount-fairing block fire-seal (3) is in the correct condition. If it is not in the correct condition, discard it and install a new rear mount-fairing block fire-seal (3).
   (2) Put and hold the rear mount-fairing block fire-seal (3) and the bracket (2) in position.
   (3) Install the nuts (1).
   (4) TORQUE the nuts (1) to between 0.17 and 0.13 m.daN (15.04 and 11.50 lbf.in ) T.
Subtask 54-57-22-420-082-B ** ON A/C NOT FOR ALL
A. Installation of the Rear Mount-Fairing Block Fire-Seal
F Rear Mount-Fairing Block Fire-Seal ** ON A/C NOT FOR ALL
   (1) Make sure that the rear mount-fairing block fire-seal (3) is in the correct condition. If it is not in the correct condition, discard it and install a new rear mount-fairing block AIPC 54-51-86-07-130 FIRE-SEAL (3) or a new rear mount-fairing block AIPC 54-51-86-07-200 FIRE-SEAL (3).
   (2) Put and hold the rear mount-fairing block fire-seal (3) and the bracket (2) in position.
   (3) Install the nuts (1).
   (4) TORQUE the nuts (1) to between 4.7 and 3.7 m.N (41.59 and 32.74 lbf.in ) T.
5. Close-up
Subtask 54-57-22-410-077-A ** ON A/C NOT FOR ALL
A. Close Access
   (1) Close the rear mount-fairing doors (Ref. AMM TASK 54-56-11-410-801).
   (2) Close the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-410-802):
     (a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
     (b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
   (3) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-802):
     (a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
     (b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
Subtask 54-57-22-440-071-A ** ON A/C NOT FOR ALL
B. Reactivation of the Thrust Reverser
   (1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-440-805).
Subtask 54-57-22-942-067-A ** ON A/C NOT FOR ALL
C. Aircraft Maintenance Configuration
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Remove the access platform(s).
   (3) Remove the WARNING NOTICE(S).
[Rev.10 from 2021] 2026.04.01 12:49:35 UTC
"Aviabrain" 2025