W DOC AIRBUS | AMM A320F

Replacement of the Aft Fixed-Fairing Seal

TASK 54-54-41-300-001-A
Replacement of the Aft Fixed-Fairing Seal

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 470
ZONE: 480
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 3M (10 FT)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
AR
WARNING NOTICE(S)
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
470
ENGINE 1 AFT PYLON
480
ENGINE 2 AFT PYLON
 D. Expendable Parts
FIG.ITEM
DESIGNATION
IPC-CSN
1
SEAL
AIPC 54-54-11-01-090
1
SEAL
AIPC 54-54-11-01-110
2
SEAL
AIPC 54-54-11-01-120
2
SEAL
AIPC 54-54-11-01-140
1
SEAL
AIPC 54-54-11-01-150
2
SEAL
AIPC 54-54-11-01-180
 E. Referenced Information
REFERENCE
DESIGNATION
TASK 29-00-00-910-002-A
Safety Procedures of the Hydraulic System
TASK 54-54-00-000-001-A-01
Removal of the Aft Fixed Fairing
TASK 54-54-00-400-001-A-01
Installation of the Aft Fixed Fairing
TASK 78-30-00-040-012-A
Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-081-041-A
Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-081-041-B
Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-440-012-A
Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance
TASK 78-30-00-481-041-A
Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-30-00-481-041-B
Make the Thrust Reverser Unserviceable for Maintenance
F Aft Fixed-Fairing Seal ** ON A/C NOT FOR ALL
F Aft Fixed-Fairing Seal ** ON A/C NOT FOR ALL
F Aft Fixed-Fairing Seal ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 54-54-41-865-050-A ** ON A/C NOT FOR ALL
A. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUHYD/HYD PWR/B WARN/& CTL2702GJC12
121VUHYDRAULIC/HYD POWER/Y3803GXN30
123VUB HYD/ELEC PUMP2701GJAB09
123VUY HYD/ELEC/PUMP3802GXAB06
123VUY HYD/ELEC/ELEC PUMP/NORM3801GXAB03
Subtask 54-54-41-941-050-A ** ON A/C NOT FOR ALL
B. Safety Precautions
   (1) On the center pedestal, on ENG panel 115VU:
     (a) Put the WARNING NOTICE(S) to tell persons not to start the engine.
   (2) Make sure that the engine 1(2) shutdown occurred not less than five minutes before you do this procedure.
   (3) On overhead maintenance-panel 50VU:
     (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
     (b) Put the WARNING NOTICE(S) to tell persons not to energize FADEC 1(2).
   (4) Obey the safety procedures of the hydraulic system (Ref. AMM TASK 29-00-00-910-002).
Subtask 54-54-41-040-050-A ** ON A/C NOT FOR ALL
C. Aircraft Maintenance Configuration
   (1) Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).
Subtask 54-54-41-040-050-B ** ON A/C NOT FOR ALL
C. Aircraft Maintenance Configuration
   (1) Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-040-012).
Subtask 54-54-41-010-053-A ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put the ACCESS PLATFORM 3M (10 FT) in position at zone 470 (480).
Subtask 54-54-41-020-050-A ** ON A/C NOT FOR ALL
E. Removal of the Components
   (1) Remove the aft fixed fairing (Ref. AMM TASK 54-54-00-000-001).
4. Procedure
Subtask 54-54-41-010-051-A ** ON A/C NOT FOR ALL
A. Removal of the Aft Fixed-Fairing Seals
   (1) Remove and discard the seals (1) and (2) from the retainers.
   (2) Clean the retainers with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
Subtask 54-54-41-410-050-A ** ON A/C NOT FOR ALL
B. Installation of the Aft Fixed-Fairing Seals
   (1) Put the new AIPC 54-54-11-01-090 SEAL (1), the new AIPC 54-54-11-01-110 SEAL (1) or the new AIPC 54-54-11-01-150 SEAL (1) and the new AIPC 54-54-11-01-120 SEAL (2), the new AIPC 54-54-11-01-140 SEAL (2) or the new AIPC 54-54-11-01-180 SEAL (2) in position on the retainers.
5. Close-up
Subtask 54-54-41-420-051-A ** ON A/C NOT FOR ALL
A. Installation of the Components
   (1) Install the aft fixed fairing (Ref. AMM TASK 54-54-00-400-001).
Subtask 54-54-41-440-050-A ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
   (1) Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-081-041).
Subtask 54-54-41-440-050-B ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
   (1) Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-440-012).
Subtask 54-54-41-865-051-A ** ON A/C NOT FOR ALL
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUHYD/HYD PWR/B WARN/& CTL2702GJC12
121VUHYDRAULIC/HYD POWER/Y3803GXN30
123VUB HYD/ELEC PUMP2701GJAB09
123VUY HYD/ELEC/PUMP3802GXAB06
123VUY HYD/ELEC/ELEC PUMP/NORM3801GXAB03
Subtask 54-54-41-942-050-A ** ON A/C NOT FOR ALL
D. Put the aircraft back to its initial configuration.
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Remove the access platform(s).
   (3) Remove the WARNING NOTICE(S).
[Rev.10 from 2021] 2026.04.01 02:03:04 UTC
"Aviabrain" 2025