Removal of the fixed APU Diverter (APS 3200)

TASK 49-16-41-000-004-A
Removal of the fixed APU Diverter (APS 3200)

1. Reason for the Job
Self explanatory.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	SCRAPER - NON METALLIC

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
315AL, 316AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
TASK 49-16-43-000-002-A	Removal of the Air Intake Flap (APS 3200)
TASK 52-41-00-010-001-A	Open the APU Doors for Access
TASK 52-41-23-010-801-A	Opening of Access Door 314AR
Fixed Diverter

3. Job Set-up
Subtask 49-16-41-860-059-B ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Put the warning notices on panel 25VU to tell persons not to start the APU.
(2) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
(3) Make sure that the hydraulic systems are depressurized (Ref. AMM TASK 29-14-00-614-001).

Subtask 49-16-41-010-058-B ** ON A/C NOT FOR ALL

B. Get Access

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(1) Put on and attach a safety harness before you start work in the work area
(2) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE below the APU access doors 315AL, 316AR and the maintenance door 314AR.
(3) Open access door 314AR and safety it in the open position.
(Ref. AMM TASK 52-41-23-010-801).
(4) Set the LIGHT control switch 3LJ to the ON position.
(5) Open the APU access doors 315AL 316AR (Ref. AMM TASK 52-41-00-010-001).
(6) Set the LIGHT control switch 11LJ to the ON position.
(7) Remove the air intake flap (Ref. AMM TASK 49-16-43-000-002)

Subtask 49-16-41-865-069-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

4. Procedure
Subtask 49-16-41-020-053-B ** ON A/C NOT FOR ALL

A. Removal of the fixed Diverter
(1) Remove the sealant from the screws (1) and washers (2) with a SCRAPER - NON METALLIC.
(2) Remove the screws (1) and the washers (2).
(3) Remove the nuts (5), the washers (6) and the screws (4).
(4) Remove the screws (7) and the washers (8).
(5) Remove the screws (9) and the washers (10), (11).
(6) Remove the sealant around the fixed diverter (12) with a non-metallic scraper.
(7) Remove the fixed diverter (12) and the shim (3).

[Rev.10 from 2021] 2026.04.01 01:27:45 UTC