DOC AIRBUS | AMM A320FInstallation of the APU Overheat Sensing-Elements
TASK 36-22-17-400-001-A
Installation of the APU Overheat Sensing-Elements
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Expendable Parts
E. Referenced Information
3. Job Set-up
Subtask 36-22-17-860-050-A ** ON A/C NOT FOR ALL
Subtask 36-22-17-210-050-A
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Install the grommet (4) on the sensing element.
(4) Put the sensing element in the correct installation position.
(5) Put the grommet (4) in position on the sensing element.
(6) Install the sensing element with the attached grommet (4) to the clamp (5).
(8) Remove the blanking caps from the electrical connector(s) and the receptacle(s).
(9) Install the socket of the sensing element to the bracket.
(10) Install the bonding jumper to the socket.
(11) Install the retaining nut (1) and TORQUE it to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in )
.
(12) Safety the retaining nut (1) and the socket with lockwire, corrosion-resistant steel dia. 0.8 mm (0.032 in.) to the bracket.
(13) Install the union nut (2) to the socket and TORQUE it to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in ).
(14) Safety the union nut (2) with lockwire, corrosion-resistant steel dia 0.8 mm (0.032 in.) to the retaining nut (1).
(15) On the bulkhead remove the blanking caps from the electrical connector(s).
(16) Clean the area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) .
(17) Make sure that you have a dry surface.
(18) Clean the bulkhead connection (6) with a BRUSH - NON METALLIC.
(19) Put the bulkhead connection (6) in position.
(20) Put the new AIPC 36-22-04-01-130 SEALING RING (7) or AIPC 36-22-84-01-130 SEALING RING (7) and washer (8) in position on the bulkhead connection (6).
(22) Install the union nut (2) to the bulkhead connection (6) and TORQUE to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in ).
(23) Safety the union nut (2) with lockwire, corrosion-resistant steel dia. 0.8 mm (0.032 in.) to the bulkhead connection (6).
Subtask 36-22-17-865-052-A
Subtask 36-22-17-410-051-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 12:39:16 UTC
Installation of the APU Overheat Sensing-Elements
WARNING:
MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START WORK. PRESSURIZED AIR CAN CAUSE INJURY TO PERSONNEL.
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
NOTE: The installation procedure for all sensing elements of the leak detection system (single loop 125 degree) is the same.
FIN: 11HF
FIN: 12HF
FIN: 13HF
FIN: 14HF
FIN: 15HF
FIN: 16HF
FIN: 17HF
FIN: 18HF
FIN: 19HF
FIN: 20HF
FIN: 84HF ** ON A/C NOT FOR ALL
1. Reason for the JobFIN: 12HF
FIN: 13HF
FIN: 14HF
FIN: 15HF
FIN: 16HF
FIN: 17HF
FIN: 18HF
FIN: 19HF
FIN: 20HF
FIN: 84HF ** ON A/C NOT FOR ALL
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE |
| No specific | 1 | BRUSH - NON METALLIC |
| No specific | Torque wrench: range to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in ) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.06AEA1) | Polysulfide Sealant-Low Adhesion Brushable - |
| (Material No.06AEB2) | Polysulfide Sealant-Low Adhesion Fillet Structure |
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| No specific | lockwire, corrosion-resistant steel dia 0.8 mm (0.032 in.) |
| No specific | lockwire, corrosion-resistant steel dia. 0.8 mm (0.032 in.) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 151BW, 161AW, 161BW, 161CW, 161DW, 312AR, 314AR | |
| 151CW, 151DW, 151EW, 151HW, 151JW | |
| 197BB | |
| 151RW, 197KB | |
| 151SW, 151TW, 151UW, 151VW |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 7 | SEALING RING | AIPC 36-22-04-01-130 |
| 7 | SEALING RING | AIPC 36-22-84-01-130 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 25-55-11-000-001-A | Removal of the Aft Cargo-Compartment Partition at FR47 |
| TASK 25-55-11-400-001-A | Installation of the Aft Cargo-Compartment Partition at FR47 |
| TASK 25-55-12-000-001-A | Removal of the Aft Cargo-Compartment Partition at FR65 |
| TASK 25-55-12-400-001-A | Installation of the Aft Cargo-Compartment Partition at FR65 |
| TASK 36-22-00-710-001-A | Operational Test of the Overheat Detection System |
| TASK 36-22-00-710-802-A | Operational Test of the Overheat Detection System |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
APU Overheat Sensing-ElementsSubtask 36-22-17-860-050-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) For access to the overheat sensing elements between FR49 and FR50:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position.
(b) Make sure that the access panel 197BB is open.
(2) For access to the APU overheat sensing elements between FR46 and FR70 from the AFT cargo compartment:
(a) Make sure that the AFT cargo compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(3) For access to the APU overheat sensing elements between the FR46 and FR47:
(a) Make sure that the partition panel 151BW is removed (Ref. AMM TASK 25-55-11-000-001).
(4) For access to the APU overheat sensing elements between the FR47 and FR49:
(a) Make sure that the access panel 151CW is removed.
(5) For access to the APU overheat sensing elements between the FR49 and FR52:
(a) Make sure that the access panel 151DW is removed.
(6) For access to the APU overheat sensing elements between the FR52 and FR55:
(a) Make sure that the access panel 151EW is removed.
(7) For access to the APU overheat sensing elements between the FR55 and FR58:
(a) Make sure that the access panel 151HW is removed.
(8) For access to the APU overheat sensing elements between the FR58 and FR59:
(a) Make sure that the access panel 151JW is removed.
(9) For access to the APU overheat sensing elements between the FR59 and FR62:
(a) Make sure that the access panel 161AW is removed.
(10) For access to the APU overheat sensing elements between the FR62 and FR63:
(a) Make sure that the access panel 161BW is removed.
(11) For access to the APU overheat sensing elements between the FR63 and FR65:
(a) Make sure that the access panel 161CW is removed.
(12) For access to the APU overheat sensing elements between the FR65 and FR70:
(a) Make sure that the partition panel 161DW is removed (Ref. AMM TASK 25-55-12-000-001).
(13) For access to the APU overheat sensing elements aft of FR70:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position below the rear fuselage.
(14) For access to the APU overheat sensing elements between the FR70 and FR77:
(a) Make sure that the access door 312AR is open.
(15) For access to the APU overheat sensing elements aft of FR77:
(a) Make sure that the access door 314AR is open.
Subtask 36-22-17-860-050-B ** ON A/C NOT FOR ALL (1) For access to the overheat sensing elements between FR49 and FR50:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position.
(b) Make sure that the access panel 197BB is open.
(2) For access to the APU overheat sensing elements between FR46 and FR70 from the AFT cargo compartment:
(a) Make sure that the AFT cargo compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(3) For access to the APU overheat sensing elements between the FR46 and FR47:
(a) Make sure that the partition panel 151BW is removed (Ref. AMM TASK 25-55-11-000-001).
(4) For access to the APU overheat sensing elements between the FR47 and FR49:
(a) Make sure that the access panel 151CW is removed.
(5) For access to the APU overheat sensing elements between the FR49 and FR52:
(a) Make sure that the access panel 151DW is removed.
(6) For access to the APU overheat sensing elements between the FR52 and FR55:
(a) Make sure that the access panel 151EW is removed.
(7) For access to the APU overheat sensing elements between the FR55 and FR58:
(a) Make sure that the access panel 151HW is removed.
(8) For access to the APU overheat sensing elements between the FR58 and FR59:
(a) Make sure that the access panel 151JW is removed.
(9) For access to the APU overheat sensing elements between the FR59 and FR62:
(a) Make sure that the access panel 161AW is removed.
(10) For access to the APU overheat sensing elements between the FR62 and FR63:
(a) Make sure that the access panel 161BW is removed.
(11) For access to the APU overheat sensing elements between the FR63 and FR65:
(a) Make sure that the access panel 161CW is removed.
(12) For access to the APU overheat sensing elements between the FR65 and FR70:
(a) Make sure that the partition panel 161DW is removed (Ref. AMM TASK 25-55-12-000-001).
(13) For access to the APU overheat sensing elements aft of FR70:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position below the rear fuselage.
(14) For access to the APU overheat sensing elements between the FR70 and FR77:
(a) Make sure that the access door 312AR is open.
(15) For access to the APU overheat sensing elements aft of FR77:
(a) Make sure that the access door 314AR is open.
A. Aircraft Maintenance Configuration
(1) For access to the overheat sensing elements between FR49 and FR50:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position.
(b) Make sure that the access panel 197KB is open.
(2) For access to the APU overheat sensing elements between FR46 and FR70 from the AFT cargo compartment:
(a) Make sure that the AFT cargo compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(3) For access to the APU overheat sensing elements between the FR46 and FR47:
(a) Make sure that the partition panel 151BW is removed (Ref. AMM TASK 25-55-11-000-001).
(4) For access to the APU overheat sensing elements between the FR47 and FR47.4:
(a) Make sure that the access panel 151RW is removed.
(5) For access to the APU overheat sensing elements between the FR47.4 and FR49:
(a) Make sure that the access panel 151CW is removed.
(6) For access to the APU overheat sensing elements between the FR49 and FR52:
(a) Make sure that the access panel 151DW is removed.
(7) For access to the APU overheat sensing elements between the FR52 and FR55:
(a) Make sure that the access panel 151EW is removed.
(8) For access to the APU overheat sensing elements between the FR55 and FR58:
(a) Make sure that the access panel 151HW is removed.
(9) For access to the APU overheat sensing elements between the FR58 and FR59:
(a) Make sure that the access panel 151JW is removed.
(10) For access to the APU overheat sensing elements between the FR59 and FR62:
(a) Make sure that the access panel 161AW is removed.
(11) For access to the APU overheat sensing elements between the FR62 and FR63:
(a) Make sure that the access panel 161BW is removed.
(12) For access to the APU overheat sensing elements between the FR63 and FR65:
(a) Make sure that the access panel 161CW is removed.
(13) For access to the APU overheat sensing elements between the FR65 and FR70:
(a) Make sure that the partition panel 161DW is removed (Ref. AMM TASK 25-55-12-000-001).
(14) For access to the APU overheat sensing elements aft of FR70:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position below the rear fuselage.
(15) For access to the APU overheat sensing elements between the FR70 and FR77:
(a) Make sure that the access door 312AR is open.
(16) For access to the APU overheat sensing elements aft of FR77:
(a) Make sure that the access door 314AR is open.
Subtask 36-22-17-860-050-C ** ON A/C NOT FOR ALL (1) For access to the overheat sensing elements between FR49 and FR50:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position.
(b) Make sure that the access panel 197KB is open.
(2) For access to the APU overheat sensing elements between FR46 and FR70 from the AFT cargo compartment:
(a) Make sure that the AFT cargo compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(3) For access to the APU overheat sensing elements between the FR46 and FR47:
(a) Make sure that the partition panel 151BW is removed (Ref. AMM TASK 25-55-11-000-001).
(4) For access to the APU overheat sensing elements between the FR47 and FR47.4:
(a) Make sure that the access panel 151RW is removed.
(5) For access to the APU overheat sensing elements between the FR47.4 and FR49:
(a) Make sure that the access panel 151CW is removed.
(6) For access to the APU overheat sensing elements between the FR49 and FR52:
(a) Make sure that the access panel 151DW is removed.
(7) For access to the APU overheat sensing elements between the FR52 and FR55:
(a) Make sure that the access panel 151EW is removed.
(8) For access to the APU overheat sensing elements between the FR55 and FR58:
(a) Make sure that the access panel 151HW is removed.
(9) For access to the APU overheat sensing elements between the FR58 and FR59:
(a) Make sure that the access panel 151JW is removed.
(10) For access to the APU overheat sensing elements between the FR59 and FR62:
(a) Make sure that the access panel 161AW is removed.
(11) For access to the APU overheat sensing elements between the FR62 and FR63:
(a) Make sure that the access panel 161BW is removed.
(12) For access to the APU overheat sensing elements between the FR63 and FR65:
(a) Make sure that the access panel 161CW is removed.
(13) For access to the APU overheat sensing elements between the FR65 and FR70:
(a) Make sure that the partition panel 161DW is removed (Ref. AMM TASK 25-55-12-000-001).
(14) For access to the APU overheat sensing elements aft of FR70:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position below the rear fuselage.
(15) For access to the APU overheat sensing elements between the FR70 and FR77:
(a) Make sure that the access door 312AR is open.
(16) For access to the APU overheat sensing elements aft of FR77:
(a) Make sure that the access door 314AR is open.
A. Aircraft Maintenance Configuration
(1) For access to the overheat sensing elements between FR49 and FR50:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position.
(b) Make sure that the access panel 197BB is open.
(2) For access to the APU overheat sensing elements between FR46 and FR70 from the AFT cargo compartment:
(a) Make sure that the AFT cargo compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(3) For access to the APU overheat sensing elements between the FR46 and FR53:
(a) Make sure that the partition panel 151BW is removed (Ref. AMM TASK 25-55-11-000-001).
(b) Make sure that the access panel 151SW is removed.
(4) For access to the APU overheat sensing elements between the FR53 and FR56:
(a) Make sure that the access panel 151TW is removed.
(5) For access to the APU overheat sensing elements between the FR56 and FR58:
(a) Make sure that the access panel 151UW is removed.
(6) For access to the APU overheat sensing elements between the FR58 and FR59:
(a) Make sure that the access panel 151VW is removed.
(7) For access to the APU overheat sensing elements between the FR59 and FR62:
(a) Make sure that the access panel 161AW is removed.
(8) For access to the APU overheat sensing elements between the FR62 and FR63:
(a) Make sure that the access panel 161BW is removed.
(9) For access to the APU overheat sensing elements between the FR63 and FR65:
(a) Make sure that the access panel 161CW is removed.
(10) For access to the APU overheat sensing elements between the FR65 and FR70:
(a) Make sure that the partition panel 161DW is removed (Ref. AMM TASK 25-55-12-000-001).
(11) For access to the APU overheat sensing elements aft of FR70:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position below the rear fuselage.
(12) For access to the APU overheat sensing elements between the FR70 and FR77:
(a) Make sure that the access door 312AR is open.
(13) For access to the APU overheat sensing elements aft of FR77:
(a) Make sure that the access door 314AR is open.
Subtask 36-22-17-865-051-A (1) For access to the overheat sensing elements between FR49 and FR50:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position.
(b) Make sure that the access panel 197BB is open.
(2) For access to the APU overheat sensing elements between FR46 and FR70 from the AFT cargo compartment:
(a) Make sure that the AFT cargo compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(3) For access to the APU overheat sensing elements between the FR46 and FR53:
(a) Make sure that the partition panel 151BW is removed (Ref. AMM TASK 25-55-11-000-001).
(b) Make sure that the access panel 151SW is removed.
(4) For access to the APU overheat sensing elements between the FR53 and FR56:
(a) Make sure that the access panel 151TW is removed.
(5) For access to the APU overheat sensing elements between the FR56 and FR58:
(a) Make sure that the access panel 151UW is removed.
(6) For access to the APU overheat sensing elements between the FR58 and FR59:
(a) Make sure that the access panel 151VW is removed.
(7) For access to the APU overheat sensing elements between the FR59 and FR62:
(a) Make sure that the access panel 161AW is removed.
(8) For access to the APU overheat sensing elements between the FR62 and FR63:
(a) Make sure that the access panel 161BW is removed.
(9) For access to the APU overheat sensing elements between the FR63 and FR65:
(a) Make sure that the access panel 161CW is removed.
(10) For access to the APU overheat sensing elements between the FR65 and FR70:
(a) Make sure that the partition panel 161DW is removed (Ref. AMM TASK 25-55-12-000-001).
(11) For access to the APU overheat sensing elements aft of FR70:
(a) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position below the rear fuselage.
(12) For access to the APU overheat sensing elements between the FR70 and FR77:
(a) Make sure that the access door 312AR is open.
(13) For access to the APU overheat sensing elements aft of FR77:
(a) Make sure that the access door 314AR is open.
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/ENG 1/CTL | 3HA1 | D12 |
| 49VU | AIR BLEED/ENG 1/MONG | 2HA1 | D11 |
| ** ON A/C ALL | |||
| 49VU | AIR BLEED/X FEED/VALVE/BAT | 2HV | D13 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/ENG 2/MONG | 3HA2 | D12 |
| 49VU | AIR BLEED/ENG 1/CTL | 2HA1 | D11 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR BLEED/ENG 2/CTL | 3HA2 | Z23 |
| 122VU | AIR BLEED/ENG 2/MONG | 2HA2 | Z22 |
| ** ON A/C ALL | |||
| 122VU | AIR BLEED/X FEED VALVE/NORM | 1HV | Z20 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR BLEED/ENG 1/MONG | 3HA1 | Z23 |
| 122VU | AIR BLEED/ENG 2/CTL | 2HA2 | Z22 |
Subtask 36-22-17-210-050-A
A. Inspection of the Replacement Components
(1) Make sure that the sensing element is not damaged (flat or nicked).
(2) Make sure that the threaded section of the connector and socket are in the correct condition. Make sure that the center pin of the connector is free of corrosion, distortion, dirt and contamination.
(3) Make sure that the clamp is in the correct condition. Make sure that it is correctly attached to the structure and can be correctly locked.
Subtask 36-22-17-420-051-A (1) Make sure that the sensing element is not damaged (flat or nicked).
(2) Make sure that the threaded section of the connector and socket are in the correct condition. Make sure that the center pin of the connector is free of corrosion, distortion, dirt and contamination.
(3) Make sure that the clamp is in the correct condition. Make sure that it is correctly attached to the structure and can be correctly locked.
CAUTION:
REMOVE OR INSTALL THE SENSING ELEMENTS CAREFULLY. DO NOT TWIST, BEND OR CAUSE KINKS IN THE SENSING ELEMENTS. IF YOU DO, YOU CAN CAUSE DAMAGE TO THEM.
B. Installation of the Sensing-Elements NOTE: Obey the permitted tolerances for the installation of the sensing elements:
and
Make sure that the clearance between the sensing element and the duct is approximately 12.7 mm (0.5000 in.), measured over the full length of the sensing element.
(1) Clean the component interfaces and the adjacent area.and
Make sure that the clearance between the sensing element and the duct is approximately 12.7 mm (0.5000 in.), measured over the full length of the sensing element.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Install the grommet (4) on the sensing element.
(4) Put the sensing element in the correct installation position.
(5) Put the grommet (4) in position on the sensing element.
(6) Install the sensing element with the attached grommet (4) to the clamp (5).
NOTE: The slot of the grommet must be on the opposite to the camloc of the clamp.
(7) Close the clamp (5) and tighten the camloc (3). (8) Remove the blanking caps from the electrical connector(s) and the receptacle(s).
(9) Install the socket of the sensing element to the bracket.
(10) Install the bonding jumper to the socket.
(11) Install the retaining nut (1) and TORQUE it to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in )
. (12) Safety the retaining nut (1) and the socket with lockwire, corrosion-resistant steel dia. 0.8 mm (0.032 in.) to the bracket.
(13) Install the union nut (2) to the socket and TORQUE it to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in )
. (14) Safety the union nut (2) with lockwire, corrosion-resistant steel dia 0.8 mm (0.032 in.) to the retaining nut (1).
(15) On the bulkhead remove the blanking caps from the electrical connector(s).
(16) Clean the area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) .
(17) Make sure that you have a dry surface.
(18) Clean the bulkhead connection (6) with a BRUSH - NON METALLIC.
(19) Put the bulkhead connection (6) in position.
(20) Put the new AIPC 36-22-04-01-130 SEALING RING (7) or AIPC 36-22-84-01-130 SEALING RING (7) and washer (8) in position on the bulkhead connection (6).
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(21) Apply one of these sealants: Polysulfide Sealant-Low Adhesion Brushable - (Material No.06AEA1) or Polysulfide Sealant-Low Adhesion Fillet Structure (Material No.06AEB2) to the bulkhead connection (6) on the pressurized side. (22) Install the union nut (2) to the bulkhead connection (6) and TORQUE to between 0.69 and 0.58 m.daN (61.06 and 51.33 lbf.in )
. (23) Safety the union nut (2) with lockwire, corrosion-resistant steel dia. 0.8 mm (0.032 in.) to the bulkhead connection (6).
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 36-22-17-710-050-A ** ON A/C NOT FOR ALL Subtask 36-22-17-710-050-B ** ON A/C NOT FOR ALL 5. Close-up| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/ENG 1/CTL | 3HA1 | D12 |
| 49VU | AIR BLEED/ENG 1/MONG | 2HA1 | D11 |
| ** ON A/C ALL | |||
| 49VU | AIR BLEED/X FEED/VALVE/BAT | 2HV | D13 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR BLEED/ENG 2/MONG | 3HA2 | D12 |
| 49VU | AIR BLEED/ENG 1/CTL | 2HA1 | D11 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR BLEED/ENG 2/CTL | 3HA2 | Z23 |
| 122VU | AIR BLEED/ENG 2/MONG | 2HA2 | Z22 |
| ** ON A/C ALL | |||
| 122VU | AIR BLEED/X FEED VALVE/NORM | 1HV | Z20 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR BLEED/ENG 1/MONG | 3HA1 | Z23 |
| 122VU | AIR BLEED/ENG 2/CTL | 2HA2 | Z22 |
Subtask 36-22-17-410-051-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For the overheat sensing elements between FR49 and FR50:
(a) Install the access panel 197BB.
(3) For the APU overheat sensing elements between the FR46 and FR47:
(a) Install the partition panel 151BW (Ref. AMM TASK 25-55-11-400-001).
(4) For the APU overheat sensing elements between the FR47 and FR49:
(a) Install the access panel 151CW.
(5) For the APU overheat sensing elements between the FR49 and FR52:
(a) Install the access panel 151DW.
(6) For the APU overheat sensing elements between the FR52 and FR55:
(a) Install the access panel 151EW.
(7) For the APU overheat sensing elements between the FR55 and FR58:
(a) Install the access panel 151HW.
(8) For the APU overheat sensing elements between the FR58 and FR59:
(a) Install the access panel 151JW.
(9) For the APU overheat sensing elements between the FR59 and FR62:
(a) Install the access panel 161AW.
(10) For the APU overheat sensing elements between the FR62 and FR63:
(a) Install the access panel 161BW.
(11) For the APU overheat sensing elements between the FR63 and FR65:
(a) Install the access panel 161CW.
(12) For the APU overheat sensing elements between the FR65 and FR70:
(a) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(13) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(14) For the APU overheat sensing elements between the FR70 and FR77:
(a) Close the access door 312AR.
(15) For the APU overheat sensing elements aft of FR77:
(a) Close the access door 314AR.
(16) Remove the access platform(s).
Subtask 36-22-17-410-051-B ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) For the overheat sensing elements between FR49 and FR50:
(a) Install the access panel 197BB.
(3) For the APU overheat sensing elements between the FR46 and FR47:
(a) Install the partition panel 151BW (Ref. AMM TASK 25-55-11-400-001).
(4) For the APU overheat sensing elements between the FR47 and FR49:
(a) Install the access panel 151CW.
(5) For the APU overheat sensing elements between the FR49 and FR52:
(a) Install the access panel 151DW.
(6) For the APU overheat sensing elements between the FR52 and FR55:
(a) Install the access panel 151EW.
(7) For the APU overheat sensing elements between the FR55 and FR58:
(a) Install the access panel 151HW.
(8) For the APU overheat sensing elements between the FR58 and FR59:
(a) Install the access panel 151JW.
(9) For the APU overheat sensing elements between the FR59 and FR62:
(a) Install the access panel 161AW.
(10) For the APU overheat sensing elements between the FR62 and FR63:
(a) Install the access panel 161BW.
(11) For the APU overheat sensing elements between the FR63 and FR65:
(a) Install the access panel 161CW.
(12) For the APU overheat sensing elements between the FR65 and FR70:
(a) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(13) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(14) For the APU overheat sensing elements between the FR70 and FR77:
(a) Close the access door 312AR.
(15) For the APU overheat sensing elements aft of FR77:
(a) Close the access door 314AR.
(16) Remove the access platform(s).
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For the overheat sensing elements between FR49 and FR50:
(a) Install the access panel 197KB.
(3) For the APU overheat sensing elements between the FR46 and FR47:
(a) Install the partition panel 151BW (Ref. AMM TASK 25-55-11-400-001).
(4) For the APU overheat sensing elements between the FR47 and 47.4:
(a) Install the access panel 151RW.
(5) For the APU overheat sensing elements between the FR47.4 and FR49:
(a) Install the access panel 151CW.
(6) For the APU overheat sensing elements between the FR49 and FR52:
(a) Install the access panel 151DW.
(7) For the APU overheat sensing elements between the FR52 and FR55:
(a) Install the access panel 151EW.
(8) For the APU overheat sensing elements between the FR55 and FR58:
(a) Install the access panel 151HW.
(9) For the APU overheat sensing elements between FR58 and FR59:
(a) Install the access panel 151JW.
(10) For the APU overheat sensing elements between the FR59 and FR62:
(a) Install the access panel 161AW.
(11) For the APU overheat sensing elements ducts between the FR62 and FR63:
(a) Install the access panel 161BW.
(12) For the APU overheat sensing elements between the FR63 and FR65:
(a) Install the access panel 161CW.
(13) For the APU overheat sensing elements between the FR65 and FR70:
(a) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(14) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(15) For the APU overheat sensing elements between the FR70 and FR77:
(a) Close the access door 312AR.
(16) For the APU overheat sensing elements aft of FR77:
(a) Close the access door 314AR.
(17) Remove the access platform(s).
Subtask 36-22-17-410-051-C ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) For the overheat sensing elements between FR49 and FR50:
(a) Install the access panel 197KB.
(3) For the APU overheat sensing elements between the FR46 and FR47:
(a) Install the partition panel 151BW (Ref. AMM TASK 25-55-11-400-001).
(4) For the APU overheat sensing elements between the FR47 and 47.4:
(a) Install the access panel 151RW.
(5) For the APU overheat sensing elements between the FR47.4 and FR49:
(a) Install the access panel 151CW.
(6) For the APU overheat sensing elements between the FR49 and FR52:
(a) Install the access panel 151DW.
(7) For the APU overheat sensing elements between the FR52 and FR55:
(a) Install the access panel 151EW.
(8) For the APU overheat sensing elements between the FR55 and FR58:
(a) Install the access panel 151HW.
(9) For the APU overheat sensing elements between FR58 and FR59:
(a) Install the access panel 151JW.
(10) For the APU overheat sensing elements between the FR59 and FR62:
(a) Install the access panel 161AW.
(11) For the APU overheat sensing elements ducts between the FR62 and FR63:
(a) Install the access panel 161BW.
(12) For the APU overheat sensing elements between the FR63 and FR65:
(a) Install the access panel 161CW.
(13) For the APU overheat sensing elements between the FR65 and FR70:
(a) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(14) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(15) For the APU overheat sensing elements between the FR70 and FR77:
(a) Close the access door 312AR.
(16) For the APU overheat sensing elements aft of FR77:
(a) Close the access door 314AR.
(17) Remove the access platform(s).
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For the overheat sensing elements between FR49 and FR50:
(a) Install the access panel 197BB.
(3) For the APU overheat sensing elements between the FR46 and FR53:
(a) Install the partition panel 151BW (Ref. AMM TASK 25-55-11-400-001).
(b) Install the access panel 151SW.
(4) For the APU overheat sensing elements between the FR53 and FR56:
(a) Install the access panel 151TW.
(5) For the APU overheat sensing elements between the FR56 and FR58:
(a) Install the access panel 151UW.
(6) For the APU overheat sensing elements between the FR58 and FR59:
(a) Install the access panel 151VW.
(7) For the APU overheat sensing elements between the FR59 and FR62:
(a) Install the access panel 161AW.
(8) For the APU overheat sensing elements between FR62 and FR63:
(a) Install the access panel 161BW.
(9) For the APU overheat sensing elements between the FR63 and FR65:
(a) Install the access panel 161CW.
(10) For the APU overheat sensing elements between the FR65 and FR70:
(a) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(11) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(12) For the APU overheat sensing elements between the FR70 and FR77:
(a) Close the access door 312AR.
(13) For the APU overheat sensing elements aft of FR77:
(a) Close the access door 314AR.
(14) Remove the access platform(s).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For the overheat sensing elements between FR49 and FR50:
(a) Install the access panel 197BB.
(3) For the APU overheat sensing elements between the FR46 and FR53:
(a) Install the partition panel 151BW (Ref. AMM TASK 25-55-11-400-001).
(b) Install the access panel 151SW.
(4) For the APU overheat sensing elements between the FR53 and FR56:
(a) Install the access panel 151TW.
(5) For the APU overheat sensing elements between the FR56 and FR58:
(a) Install the access panel 151UW.
(6) For the APU overheat sensing elements between the FR58 and FR59:
(a) Install the access panel 151VW.
(7) For the APU overheat sensing elements between the FR59 and FR62:
(a) Install the access panel 161AW.
(8) For the APU overheat sensing elements between FR62 and FR63:
(a) Install the access panel 161BW.
(9) For the APU overheat sensing elements between the FR63 and FR65:
(a) Install the access panel 161CW.
(10) For the APU overheat sensing elements between the FR65 and FR70:
(a) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(11) Close the AFT cargo compartment door (Ref. AMM TASK 52-30-00-860-002).
(12) For the APU overheat sensing elements between the FR70 and FR77:
(a) Close the access door 312AR.
(13) For the APU overheat sensing elements aft of FR77:
(a) Close the access door 314AR.
(14) Remove the access platform(s).