Deactivation of the Landing Lights

TASK 33-42-00-040-001-A
Deactivation of the Landing Lights

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: MAKE SURE THAT THERE ARE NO SIGNS OF FUEL CONTAMINATION IN THE LANDING LIGHT ASSEMBLY. IF YOU FIND FUEL CONTAMINATION, NO PERSON MUST OPERATE THE LANDING LIGHT UNTIL:

YOU REPAIR THE FUEL LEAK
YOU REPLACE THE LANDING LIGHT ASSEMBLY.

IF YOU DO NOT OBEY THIS PRECAUTION, IGNITION OF THE REMAINING FUEL IN THE LANDING LIGHT CAN OCCUR.

FIN: 7LB
FIN: 8LB

1. Reason for the Job
CDL 33-07
Landing Light Lens 7LB, 8LB
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	1	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RAB9)	Adhesive Film Tape-- Aluminium Foil -

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
Landing Light Hole - Location

3. Job Set-up
Subtask 33-42-00-941-052-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Put a WARNING NOTICE(S) in position on panel 25VU to tell persons not to operate the landing lights.

Subtask 33-42-00-860-051-A

B. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) If necessary, retract the applicable landing light 7LB(8LB):
(a) In zone 571 (671), make sure the travel range of the landing light is clear.
(b) In the cockpit, on the lighting panel 25VU, set the LAND L (R) switch to RETRACT.
(c) Make sure the landing light retracts.
(3) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).
(4) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable zone 571(671).

Subtask 33-42-00-865-057-A

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
FOR FIN: 7LB (LTLANDING, L)
122VU	LIGHTING/LANDING LT/L/CTL	3LB	T05
122VU	LIGHTING/LANDING LT/L/SPLY	1LB	T04
FOR FIN: 8LB (LTLANDING, R)
122VU	LIGHTING/LANDING LT/R/CTL	4LB	T07
122VU	LIGHTING/LANDING LT/R/SPLY	2LB	T06

4. Procedure
Subtask 33-42-00-040-050-A

A. Deactivation of the Landing Lights
(1) Apply Adhesive Film Tape-- Aluminium Foil - (Material No.05RAB9) across the opening of the applicable landing light 7LB(8LB).

NOTE: Make sure that the tape is correctly installed and has no bubbles, wrinkles or tears in it.

(2) Write a note in the aircraft technical log that the applicable landing light 7LB(8LB) is deactivated.

5. Close-up
Subtask 33-42-00-942-052-A

A. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 00:55:16 UTC