Read and Decode the Hardware Pin Programming of the SDAC and FWC

TASK 31-50-00-740-002-A
Read and Decode the Hardware Pin Programming of the SDAC and FWC

WARNING: MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT. UNWANTED ELECTRICAL POWER CAN BE DANGEROUS.

NOTE: Ignore all the ECAM WARNINGS as long as the computer is in the menu mode.

ZONE: 210

1. Reason for the Job
To make sure that the pin programming and parity of the SDACs and the FWCs are correct.
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 31-32-00-860-008-A	Procedure to Get Access to the SYSTEM REPORT/TEST/INST Page
AWM 315227
AWM 315228
AWM 315234
AWM 315405
AWM 315406
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E017271616)
Table of the SDAC Hardware Pin Programming Data
Table of the FWC Hardware Pin Programming Data
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E018312020 or 350E053020303)
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E053020404 or Subsequent)
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E017271616)
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E018312020 or 350E053020303)
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E053020404)
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E053020606)
ECAM-1/ECAM PIN PROGRAM HARDWARE Pages with SDAC in Full Mode and FWC std H2-F3 or subsequent (P/N: 350E053020707 or subsequent)
ECAM-1/ECAM PIN PROGRAM HARDWARE PAGES WITH FWC STANDARD H2-F8 (P/N 350E053021313 OR SUBSEQUENT) OR H2-F9 (P/N 350E053021616 OR SUBSEQUENT) OR H2-F10 (P/N 350E053022020 OR SUBSEQUENT) OR H2-F12 (P/N 350E053022121 OR SUBSEQUENT)
TABLE OF THE FWC HARDWARE PIN PROGRAMMING DATA - STANDARD H2-F8 (P/N 350E053021313 OR SUBSEQUENT) AND STANDARD H2-F9 (P/N 350E053021616 OR SUBSEQUENT)
TABLE OF THE FWC HARDWARE PIN PROGRAMMING DATA - STANDARD H2-F10 (P/N 350E053022020 OR SUBSEQUENT)
TABLE OF THE FWC HARDWARE PIN PROGRAMMING DATA - STANDARD H2-F12 (P/N 350E053022121 OR SUBSEQUENT)

3. Job Set-up
Subtask 31-50-00-860-063-A

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002)
(2) On one MCDU, get the SYSTEM REPORT/TEST/INST page. (Ref. AMM TASK 31-32-00-860-008)

Subtask 31-50-00-865-059-A

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
49VU	SDAC/1/SPLY	3WV	F04
49VU	SDAC/2/26VAC SYNC/AC ESS BUS	6WV	F03
49VU	SDAC/1/26VAC SYNC/AC ESS BUS	5WV	F02
49VU	FWS/FWC1/SPLY	3WW	F01
121VU	EIS/FWC2/SPLY	2WW	Q07
121VU	EIS/SDAC/2/SPLY	2WV	Q06
121VU	EIS/SDAC/1/BUS2/26VAC SYNC AC	7WV	Q03
121VU	EIS/SDAC/2/BUS2/26VAC SYNC AC	8WV	Q02

4. Procedure
Subtask 31-50-00-740-051-A

A. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151022 (standard H1/L8), 350E5161122 (standard H0/L8) or all SDACs in Basic Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E017271616)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with one word for the SDAC1 and one word for the SDAC2.
	NOTE: Each word has 16 digits from bit 14 (rightmost) to bit 29 (label number 007 SDI 01).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-079-A

B. Read and Decode the Pin Programming Indications of the FWC
(1) For FWC P/N: 350E017271616 (standard H1/E2).

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E017271616)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with three words for the FWC1 and three words for the FWC2.
	NOTE: The first two words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01 and 015 SDI 10). The third word has 13 concatenated digits from bit 14 (rightmost) to bit 24, bit 26 and bit 28 (label number 016 SDI 00).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-053-A

C. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151022 (standard H1/L8), 350E5161122 (standard H0/L8) or all SDACs in Basic Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E018312020 or 350E053020303)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with one word for the SDAC1 and one word for the SDAC2.
	NOTE: Each word has 16 digits from bit 14 (rightmost) to bit 29 (label number 007 SDI 01).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-080-A

D. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E018312020 (standard H1P/E3Q) or 350E053020303 (standard H2/E3P).

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E018312020 or 350E053020303)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first two words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01 and 015 SDI 10). The third word has 13 concatenated digits from bit 14 (rightmost) to bit 24, bit 26 and bit 28 (label number 016 SDI 00). The fourth word has 9 concatenated digits from bit 14 (rightmost) to bit 17, bit 22 to bit 24, bit 26 and bit 28 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-054-A

E. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151022 (standard H1/L8), 350E5161122 (standard H0/L8) or all SDACs in Basic Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E053020404 or Subsequent)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with one word for the SDAC1 and one word for the SDAC2.
	NOTE: Each word has 16 digits from bit 14 (rightmost) to bit 29 (label number 007 SDI 01).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-081-A

F. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E053020404 (standard H2/E4) or subsequent.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Basic Mode and FWC P/N: 350E053020404 or Subsequent)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, and from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-056-A

G. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151331 (standard H1/D1) or subsequent in FULL Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E017271616)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with two words for the SDAC1 and two words for the SDAC2.
	NOTE: The first word has 16 digits from bit 14 (rightmost) to bit 29 (label number 007 SDI 01). The second word has 8 digits from bit 14 (rightmost) to bit 21 (label number 007 SDI 10).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-083-A

H. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E017271616 (standard H1/E2).

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E017271616)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with three words for the FWC1 and three words for the FWC2.
	NOTE: The first two words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01 and 015 SDI 10). The third word has 13 concatenated digits from bit 14 (rightmost) to bit 24, bit 26 and bit 28 (label number 016 SDI 00).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-057-A

I. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151331 (standard H1/D1) or subsequent in Full Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E018312020 or 350E053020303)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with two words for the SDAC1 and two words for the SDAC2.
	NOTE: The first word has 16 digits from bit 14 (rightmost) to bit 29 (label number 007 SDI 01). The second word has 8 digits from bit 14 (rightmost) to bit 21 (label number 007 SDI 10).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-084-A

J. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E018312020 (standard H1P/E3Q) or 350E053020303 (standard H2/E3P).

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E018312020 or 350E053020303)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first two words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01 and 015 SDI 10). The third word has 13 concatenated digits from bit 14 (rightmost) to bit 24, bit 26 and bit 28 (label number 016 SDI 00). The fourth word has 9 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 24, bit 26 and bit 28 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-058-A

K. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151331 (standard H1/D1) or subsequent in Full Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E053020404)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with two words for the SDAC1 and two words for the SDAC2.
	NOTE: The first word has 16 digits from bit 14 (rightmost) to bit 29 (label number 007 SDI 01). The second word has 8 digits from bit 14 (rightmost) to bit 21 (label number 007 SDI 10).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-085-A

L. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E053020404 (standard H2/E4).

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E053020404)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-059-A

M. Read and Decode the Pin Programming Indications for the SDAC
(1) For SDAC P/N: 350E5151331 (standard H1/D1) or subsequent in Full Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E053020606)

These figures give the table of the SDAC hardware pin programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with two words for the SDAC1 and two words for the SDAC2.
	NOTE: Each word has 16 digits from bit 14 (rightmost) to bit 29 (label numbers 007 SDI 01 and 007 SDI 10).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin programming:
Use the table of the SDAC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-086-A

N. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E053020606 (standard H2/F2).

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages (SDAC in Full Mode and FWC P/N: 350E053020606)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-060-A

O. Read and decode the pin programming indications for the System Data Analog Converter (SDAC):
(1) For SDAC Part Numbers (P/N): 350E5151331 (standard H1/D1), 350E5500201 (standard H2/D1), 350E5500202 (standard H2/D2), 350E5500204 (standard H2/E2) and 350E5500206 (standard H2/E4) or subsequent ones in the Full Mode.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages with SDAC in Full Mode and FWC std H2-F3 or subsequent (P/N: 350E053020707 or subsequent)

These figures give the table of the SDAC hardware pin-programming data:

Table of the SDAC Hardware Pin Programming Data

NOTE: The pin programming is shown in a binary code:

0 is related to a pin that is operated (connected to the ground).
1 is related to a pin that is not operated (connected to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for SDAC1 and four words for SDAC2.
	NOTE: The first two words have 16 digits from bit 14 to bit 29 (label numbers 007 SDI 01 and 007 SDI 10). The last two words have 9 concatenated digits from bit 14 (nearest to the right) to bit 17, from bit 22 to bit 24, bit 26 and bit 28 (label numbers 005 SDI 00 and 005 SDI 10).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
2.On the data table of the SDAC hardware pin-programming:
Use the table of the SDAC hardware pin-programming to find the data of each bit.
Compare the data with the condition of the aircraft pin programming given in the AWM AWM 315405, AWM 315406.

Subtask 31-50-00-740-087-A

P. Read and Decode the Pin Programming Indications for the FWC
(1) For FWC P/N: 350E053020707 (standard H2/F3) or subsequent.

ECAM-1/ECAM PIN PROGRAM HARDWARE Pages with SDAC in Full Mode and FWC std H2-F3 or subsequent (P/N: 350E053020707 or subsequent)

These figures give the table of the FWC hardware pin programming data:

Table of the FWC Hardware Pin Programming Data

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On the MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-091-A

Q. Read and Decode the Pin Programming Indications for the FWC
(1)

ECAM-1/ECAM PIN PROGRAM HARDWARE PAGES WITH FWC STANDARD H2-F8 (P/N 350E053021313 OR SUBSEQUENT) OR H2-F9 (P/N 350E053021616 OR SUBSEQUENT) OR H2-F10 (P/N 350E053022020 OR SUBSEQUENT) OR H2-F12 (P/N 350E053022121 OR SUBSEQUENT)

TABLE OF THE FWC HARDWARE PIN PROGRAMMING DATA - STANDARD H2-F8 (P/N 350E053021313 OR SUBSEQUENT) AND STANDARD H2-F9 (P/N 350E053021616 OR SUBSEQUENT)

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On one MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-093-A

R. Read and Decode the Pin Programming Indications for the FWC
(1)

TABLE OF THE FWC HARDWARE PIN PROGRAMMING DATA - STANDARD H2-F10 (P/N 350E053022020 OR SUBSEQUENT)

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On one MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

Subtask 31-50-00-740-095-A

S. Read and Decode the Pin Programming Indications for the FWC
(1)

TABLE OF THE FWC HARDWARE PIN PROGRAMMING DATA - STANDARD H2-F12 (P/N 350E053022121 OR SUBSEQUENT)

NOTE: The pin programming is shown in binary code:

0 is related to an activated pin (wired to ground),
1 is related to a pin not activated (wired to an open circuit).

ACTION	RESULT
1.On one MCDU, on the INST menu page:	On the MCDU:
Push the line key adjacent to the ECAM 1 indication.	The ECAM 1 page comes into view after some seconds.
Push the NEXT PAGE key.	The ECAM 1/FWC1/2-SDAC1/2-ECP page comes into view.
Push the line key adjacent to the SYSTEM CONFIGURATION indication.	The ECAM-1/SYSTEM CONFIGURATION page comes into view.
Push the line key adjacent to the ECAM PIN PROGRAM HARD indication.	The ECAM-1/ECAM PIN PROGRAM page for the SDAC1 and SDAC2 comes into view.
2.On one MCDU:
Push the NEXT PAGE key.	The ECAM-1/ECAM PIN PROGRAM page comes into view with four words for the FWC1 and four words for the FWC2.
	NOTE: The first three words have 16 digits from bit 14 (rightmost) to bit 29 (label numbers 015 SDI 01, 015 SDI 10 and 016 SDI 00). The fourth word has 12 concatenated digits from bit 14 (rightmost) to bit 17, from bit 22 to bit 29 (label number 016 SDI 11).
Push the line key adjacent to the PRINT indication.	The printer prints the MCDU page.
Make sure that the indications on the printed page agree with the indications shown on the MCDU.
3.On the data table of the FWC hardware pin programming:
Use the table of the FWC hardware pin programming to find the data of each bit.
Compare the data with the state of the aircraft pin programming given in the AWM AWM 315227, AWM 315228, AWM 315234.

5. Close-up
Subtask 31-50-00-860-062-A

A. Put the aircraft back to its initial configuration.
(1) On the MCDU, push the line key adjacent to the RETURN indication until the CFDS MENU page comes into view.
(2) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002)
(3) Put the system back to the serviceable condition.
(4) Put the aircraft back to the serviceable condition.

[Rev.10 from 2021] 2026.04.01 00:37:12 UTC