Activation/Deactivation of the Avionics Data Sending

TASK 31-32-00-610-802-A
Activation/Deactivation of the Avionics Data Sending

ZONE: 210

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)

3. Job Set-up
Subtask 31-32-00-861-088-B

A. Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).

Subtask 31-32-00-865-106-A

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	AUTO FLT/MCDU/1	11CA1	B01
** ON A/C NOT FOR ALL
49VU	AUTO FLT/MCDU/1	11CA1	H07
** ON A/C NOT FOR ALL
121VU	CFDS/CFDIU/SPLY	2TW	J18
121VU	CFDS/CFDIU/BACK/UP	8TW	J17
** ON A/C ALL
121VU	AUTO FLT/MCDU/2	11CA2	N20
** ON A/C NOT FOR ALL
121VU	CFDS/CFDIU/SPLY	2TW	J41
121VU	CFDS/CFDIU/BACK/UP	8TW	J40

4. Procedure
Subtask 31-32-00-970-062-B

A. Activation/Deactivation of the Avionics Data Sending

NOTE: The actions and the results of this procedure occur on the MCDU that you use.

ACTION	RESULT
1.Adjust the brightness of the MCDU screen.
2.Push the MCDU MENU mode key.	The MCDU MENU page comes into view.
3.Push the line key adjacent to the CFDS indication.	The CFDS menu page comes into view.
4.Push the NEXT PAGE function key.
5.Access to the REPORTS PROGRAMMING page without a password: NOTE: The REPORTS PROGRAMMING page is not shown in the CFDS menu if the ACARS MU/ATSU is not installed.
Push the line key adjacent to the REPORTS PROGRAMMING indication.	The REPORTS PROGRAMMING page comes into view.
6.Access to the REPORTS PROGRAMMING page with a password: NOTE: The access to the REPORTS PROGRAMMING page is available only after selection of the password mode (access with a password). NOTE: If you use the transparent mode (free access), the ENTER PASSWORD page does not come into view.
Push the line key adjacent to the REPORTS PROGRAMMING indication.	The ENTER PASSWORD page comes into view.
Enter your password with the MCDU keyboard.
Push the line key adjacent to the ENTER indication.	The REPORTS PROGRAMMING page comes into view.
7.To change the programming:
Push the left line key adjacent to the AVIONICS DATA indication.	The programming display changes to: YES: The sending of Avionics Data report to Aircraft Communication Addressing and Reporting System (ACARS) is permitted. NO: The sending of Avionics Data report to ACARS is not permitted.

5. Close-up
Subtask 31-32-00-860-165-B

A. Put the aircraft back to its initial configuration.
(1) On the MCDU, push the line key adjacent to the RETURN indication until the CFDS menu page comes into view.
(2) Fully decrease the brightness of the MCDU screen (display off).

Subtask 31-32-00-862-069-B

B. De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 00:33:58 UTC