DOC AIRBUS | AMM A320FInstallation of the Programming Dongle
TASK 25-65-35-400-003-A
Installation of the Programming Dongle
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 25-65-35-860-052-B ** ON A/C NOT FOR ALL
Subtask 25-65-35-560-053-B ** ON A/C NOT FOR ALL
Subtask 25-65-35-410-052-B ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:41:24 UTC
Installation of the Programming Dongle
ZONE: 200
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| 261BC |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
| TASK 25-23-42-000-002-A | Removal of the Ceiling Panels - Aft Utility Area |
| TASK 25-23-42-400-002-A | Installation of the Ceiling Panels - Aft Utility Area |
| TASK 25-65-00-740-001-A | Emergency Locator Transmitter (ELT) System - BITE Test |
| TASK 25-65-00-840-001-A | Procedure after a Change of Aircraft Registration Number |
DONGLE (141 MX)Subtask 25-65-35-860-052-B ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the ceiling panel 261BC is removed (Ref. AMM TASK 25-23-42-000-002).
4. Procedure(1) Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the ceiling panel 261BC is removed (Ref. AMM TASK 25-23-42-000-002).
Subtask 25-65-35-560-053-B ** ON A/C NOT FOR ALL
A. Preparation for Installation
(1) If the aircraft registration code/number (ICAO) is changed refer to (Ref. AMM TASK 25-65-00-840-001).
Subtask 25-65-35-420-053-B ** ON A/C NOT FOR ALL (1) If the aircraft registration code/number (ICAO) is changed refer to (Ref. AMM TASK 25-65-00-840-001).
B. Installation of the Programming Dongle 141MX
(1) Make sure that the ON/OFF/ARM switch (6) is in the OFF position.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Remove the CAP-BLANKING from each electrical connector and receptacle.
(4) Make sure that all the electrical connections are clean and in the correct condition.
(5) Clean the component interfaces and the adjacent area.
(6) Connect the electrical connector (1) with the bracket (5).
(7) Connect the electrical connector (3) or the programming-dongle (2) to the connector (7) of the ELT (4).
Subtask 25-65-35-740-052-B ** ON A/C NOT FOR ALL 5. Close-up(1) Make sure that the ON/OFF/ARM switch (6) is in the OFF position.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Remove the CAP-BLANKING from each electrical connector and receptacle.
(4) Make sure that all the electrical connections are clean and in the correct condition.
(5) Clean the component interfaces and the adjacent area.
(6) Connect the electrical connector (1) with the bracket (5).
(7) Connect the electrical connector (3) or the programming-dongle (2) to the connector (7) of the ELT (4).
Subtask 25-65-35-410-052-B ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the ceiling panel 261BC (Ref. AMM TASK 25-23-42-400-002).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 25-65-35-862-052-B ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the ceiling panel 261BC (Ref. AMM TASK 25-23-42-400-002).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.