Remove Emergency Locator Transmitter (ELT) for In Shop Discard of Battery Pack of ELT

TASK 25-65-00-920-802-A
Remove Emergency Locator Transmitter (ELT) for In Shop Discard of Battery Pack of ELT

ZONE: 200
FIN: 110MX ** ON A/C NOT FOR ALL

1. Reason for the Job
Refer to the MPD TASK: 256535-03
REMOVE ELT FOR IN SHOP DISCARD OF BATTERY PACK OF ELT
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 25-65-00-710-001-A	Operational Check of ELT System by Manual Activation
TASK 25-65-00-840-001-A	Procedure after a Change of Aircraft Registration Number
TASK 25-65-35-000-001-A	Removal of the Emergency Locator Transmitter (ELT)
TASK 25-65-35-400-001-A	Installation of the Emergency Locator Transmitter (ELT)

3. Job Set-up
Subtask 25-65-00-861-061-A ** ON A/C NOT FOR ALL

A. Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001)

Subtask 25-65-00-861-061-AG ** ON A/C NOT FOR ALL

A. Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001)

4. Procedure
Subtask 25-65-00-010-065-A ** ON A/C NOT FOR ALL

A. Get Access
(1) Remove the ELT (Ref. AMM TASK 25-65-35-000-001).

Subtask 25-65-00-960-051-A ** ON A/C NOT FOR ALL

B. Workshop Procedure

NOTE: If the aircraft has a programming dongle (141MX), where the aircraft code is permanently stored, it is not necessary to change that code.

(1) Send the ELT to the workshop.
(2) If the aircraft registration code/number (ICAO) changed, or the programming equipment is not available, refer to (Ref. AMM TASK 25-65-00-840-001).

Subtask 25-65-00-410-065-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Install a serviceable ELT (Ref. AMM TASK 25-65-35-400-001).
(2) Do the operational test of the ELT (Ref. AMM TASK 25-65-00-710-001).

Subtask 25-65-00-010-065-AH ** ON A/C NOT FOR ALL

D. Get Access
(1) Remove the ELT (Ref. AMM TASK 25-65-35-000-001).

Subtask 25-65-00-960-051-AG ** ON A/C NOT FOR ALL

E. Workshop Procedure

NOTE: If the aircraft is equipped with a programming dongle (141MX), where the aircraft code is permanently stored, it is not necessary to change that code.

(1) Send the ELT to the workshop.
(2) If the aircraft registration code/number (ICAO) has changed, or the programming equipment is not available, refer to (Ref. AMM TASK 25-65-00-840-001)

Subtask 25-65-00-410-065-AH ** ON A/C NOT FOR ALL

F. Close Access
(1) Install a serviceable ELT (Ref. AMM TASK 25-65-35-400-001)
(2) Make the Operational Test (Ref. AMM TASK 25-65-00-710-001).

5. Close-up
Subtask 25-65-00-862-061-A ** ON A/C NOT FOR ALL

A. De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).

Subtask 25-65-00-862-061-AG ** ON A/C NOT FOR ALL

A. De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001)

[Rev.10 from 2021] 2026.03.31 23:41:03 UTC