DOC AIRBUS | AMM A320FInstallation of the Oven(s)
TASK 25-35-19-400-001-A
Installation of the Oven(s)
Self Explanatory
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 25-35-19-860-059-A ** ON A/C NOT FOR ALL
Subtask 25-35-19-210-051-A ** ON A/C NOT FOR ALL
Subtask 25-35-19-410-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 04:35:55 UTC
Installation of the Oven(s)
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
WARNING:
BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY (MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
ZONE: 200
1. Reason for the JobSelf Explanatory
NOTE: More than one person is necessary for this procedure.
2. Job Set-up InformationA. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | VACUUM CLEANER |
| No specific | Torque wrench: range to between 0.16 and 0.14 m.daN (14.16 and 12.39 lbf.in )  | |
| No specific | Torque wrench: range to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in ) | |
| No specific | Torque wrench: range to between 0.39 and 0.34 m.daN (34.51 and 30.09 lbf.in ) | |
| No specific | Torque wrench: range to between 0.70 and 0.56 m.daN (61.95 and 49.56 lbf.in ) | |
| No specific | Torque wrench: range to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in ) | |
| No specific | Torque wrench: range to between 0.77 and 0.63 m.daN (68.14 and 55.75 lbf.in ) | |
| FOR [6475MM] (GALLEY LOC.I) | ||
| FOR [6480MM] (GALLEY LOC.III) | ||
| No specific | Torque wrench: range to between 0.20 and 0.18 m.daN (17.70 and 15.93 lbf.in ) | |
| FOR [6482MM] (GALLEY LOC.IV A/B) | ||
| No specific | Torque wrench: range to between 0.17 and 0.14 m.daN (15.04 and 12.39 lbf.in ) | |
| No specific | Torque wrench: range to between 0.20 and 0.18 m.daN (17.70 and 15.93 lbf.in ) | |
| No specific | Torque wrench: range to between 0.40 and 0.34 m.daN (35.40 and 30.09 lbf.in ) | |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.06CMD9) | Silicone Adhesive Sealant-General Purpose One part legacy |
| No specific | sheet of paper |
| FOR [6475MM] (GALLEY LOC.I) | |
| FOR [6480MM] (GALLEY LOC.III) | |
| (Material No.05BAE1) | Threadlocking Adhesive-- Medium strength - |
| FOR [6482MM] (GALLEY LOC.IV A/B) | |
| (Material No.05BAE1) | Threadlocking Adhesive-- Medium strength - |
| (Material No.06CMD9) | Silicone Adhesive Sealant-General Purpose One part legacy |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 21-23-00-720-002-A | Functional Test of an Air Extraction Point |
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
| TASK 25-30-00-920-001-A | Remove and Discard Filter Element |
| TASK 25-35-00-710-015-A | Operational Test of the Oven |
OvenSubtask 25-35-19-860-059-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
Subtask 25-35-19-860-061-A ** ON A/C NOT FOR ALL (1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
B. At the applicable galley, on the galley control panel, make sure that the circuit breaker(s) of the oven(s) is (are) open, safetied and tagged.
Subtask 25-35-19-860-061-C ** ON A/C NOT FOR ALL B. At the applicable galley, on the galley control panel, make sure that the related circuit breaker(s) of the oven(s) is (are) open, safetied and tagged.
Subtask 25-35-19-860-054-A ** ON A/C NOT FOR ALL C. Aircraft Maintenance Configuration
(1) Make sure that the oven(s) is (are) empty.
Subtask 25-35-19-860-054-E ** ON A/C NOT FOR ALL (1) Make sure that the oven(s) is (are) empty.
C. Aircraft Maintenance Configuration
(1) If necessary, make sure that the trolley(s) is (are) removed.
Subtask 25-35-19-860-054-G ** ON A/C NOT FOR ALL (1) If necessary, make sure that the trolley(s) is (are) removed.
C. Aircraft Maintenance Configuration
(1) Make sure that all applicable doors are open to let you get access to all the parts that you must install/connect.
(2) Make sure that the oven(s) is (are) empty.
(3) If necessary, remove the trolley(s).
(4) If necessary, pull the table(s) out.
Subtask 25-35-19-860-054-KH ** ON A/C NOT FOR ALL (1) Make sure that all applicable doors are open to let you get access to all the parts that you must install/connect.
(2) Make sure that the oven(s) is (are) empty.
(3) If necessary, remove the trolley(s).
(4) If necessary, pull the table(s) out.
C. Aircraft Maintenance Configuration
(1) Make sure that the oven(s) is (are) empty.
(2) If necessary, remove the trolley(s).
(3) If necessary, pull the table(s) out.
4. Procedure(1) Make sure that the oven(s) is (are) empty.
(2) If necessary, remove the trolley(s).
(3) If necessary, pull the table(s) out.
Subtask 25-35-19-210-051-A ** ON A/C NOT FOR ALL
A. Preparation for Installation
(1) Do a visual inspection of the grille(s) and the housing(s) of the air-extraction filter(s) in the related galley:
(b) If necessary, replace the air-extraction filter element(s) (Ref. AMM TASK 25-30-00-920-001).
(2) Do the air-extraction test as follows: (Ref. AMM TASK 21-23-00-720-002)
(a) Hold a sheet of paper to the applicable air-extraction inlet(s).
(b) Make sure that the air suction holds the paper in position at the air-extraction inlet(s).
(c) Remove the paper.
(3) Clean the component interfaces and the adjacent area.
(4) Do an inspection of the component interfaces and the adjacent area.
(5) Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 25-35-19-420-050-A ** ON A/C NOT FOR ALL (1) Do a visual inspection of the grille(s) and the housing(s) of the air-extraction filter(s) in the related galley:
CAUTION:
BE CAREFUL WHEN YOU CLEAN THE GRILLS WITH A VACUUM CLEANER. IF YOU ARE NOT CAREFUL, YOU CAN CAUSE DAMAGE TO THE GRILLS.
(a) If necessary, clean the grille(s) and the housing(s) with the VACUUM CLEANER. (b) If necessary, replace the air-extraction filter element(s) (Ref. AMM TASK 25-30-00-920-001).
(2) Do the air-extraction test as follows: (Ref. AMM TASK 21-23-00-720-002)
(a) Hold a sheet of paper to the applicable air-extraction inlet(s).
(b) Make sure that the air suction holds the paper in position at the air-extraction inlet(s).
(c) Remove the paper.
(3) Clean the component interfaces and the adjacent area.
(4) Do an inspection of the component interfaces and the adjacent area.
(5) Make sure that the parts retained from the removed component are clean and in the correct condition.
B. Installation of the Oven
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(3) Make sure that all the electrical connections are clean and in the correct condition.
(4) Do an inspection of the component interfaces and the adjacent area.
(5) Put the oven (2) in position on the mounting rails (3).
(6) Carefully push the oven (2) into the galley to connect the electrical connector.
(7) Install the screws (1).
(8) TORQUE the screws (1) to between 0.77 and 0.63 m.daN (68.14 and 55.75 lbf.in ).
Subtask 25-35-19-420-050-A0 ** ON A/C NOT FOR ALL WARNING:
SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1) Prevent damage to the component interfaces and the adjacent area.(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(3) Make sure that all the electrical connections are clean and in the correct condition.
(4) Do an inspection of the component interfaces and the adjacent area.
(5) Put the oven (2) in position on the mounting rails (3).
(6) Carefully push the oven (2) into the galley to connect the electrical connector.
(7) Install the screws (1).
(8) TORQUE the screws (1) to between 0.77 and 0.63 m.daN (68.14 and 55.75 lbf.in )
. B. Installation of the Oven
(2) Make sure that all the electrical connections are clean and in the correct condition.
(3) Carefully push the oven (2) into the mounting rails (3) to connect the electrical connector.
(4) Install the screws (1).
(5) TORQUE the screws (1) to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in ).
Subtask 25-35-19-420-050-AX ** ON A/C NOT FOR ALL WARNING:
SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1) Remove the CAP-BLANKING from each electrical connector and receptacle.(2) Make sure that all the electrical connections are clean and in the correct condition.
(3) Carefully push the oven (2) into the mounting rails (3) to connect the electrical connector.
(4) Install the screws (1).
(5) TORQUE the screws (1) to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in )
. B. Installation of the Oven
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(3) Make sure that all the electrical connections are clean and in the correct condition.
(4) Put the oven (3) in position on the mounting rails (1).
(5) Carefully push the oven (3) into the galley compartment to connect the electrical connector.
(6) Install the screws (2).
(7) TORQUE the screws (2) to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in ).
Subtask 25-35-19-420-050-BG ** ON A/C NOT FOR ALL WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1) Prevent damage to the component interfaces and the adjacent area.(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(3) Make sure that all the electrical connections are clean and in the correct condition.
(4) Put the oven (3) in position on the mounting rails (1).
(5) Carefully push the oven (3) into the galley compartment to connect the electrical connector.
(6) Install the screws (2).
(7) TORQUE the screws (2) to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in )
. B. Installation of the Oven
(a) Put the bracket (3) in position and install the screws (5).
(b) TORQUE the screws (5) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in ).
(c) Remove the CAP-BLANKING from each electrical connector and receptacle.
(d) Make sure that all the electrical connections are clean and in the correct condition.
(e) Put the oven (7) on the mounting rails (1).
(f) Carefully push the oven (7) into the galley and connect the electrical connector.
(g) Install the filler (2).
(h) Clean the filler (2) and/or the adjacent area.
(i) Apply Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) on the filler (2).
(j) Put the washers (4) in position and install the screws (6).
(k) TORQUE the screws (6) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in ).
(2) Install the oven in the aft galley:
(a) Put the bracket (3) and the washers (4) in position and install the screws (5).
(b) TORQUE the screws (5) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in ).
(c) Remove the CAP-BLANKING from each electrical connector and receptacle.
(d) Make sure that all the electrical connections are clean and in the correct condition.
(e) Put the oven (7) on the mounting rails (1).
(f) Carefully push the oven (7) into the galley and connect the electrical connector.
(g) Put the washers (4) in position and install the screws (6).
(h) TORQUE the screws (6) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in ).
Subtask 25-35-19-420-050-BS ** ON A/C NOT FOR ALL WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
WARNING:
SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(1) Install the oven in the forward galley: (a) Put the bracket (3) in position and install the screws (5).
(b) TORQUE the screws (5) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in )
. (c) Remove the CAP-BLANKING from each electrical connector and receptacle.
(d) Make sure that all the electrical connections are clean and in the correct condition.
(e) Put the oven (7) on the mounting rails (1).
(f) Carefully push the oven (7) into the galley and connect the electrical connector.
(g) Install the filler (2).
(h) Clean the filler (2) and/or the adjacent area.
(i) Apply Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) on the filler (2).
(j) Put the washers (4) in position and install the screws (6).
(k) TORQUE the screws (6) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in )
. (2) Install the oven in the aft galley:
(a) Put the bracket (3) and the washers (4) in position and install the screws (5).
(b) TORQUE the screws (5) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in )
. (c) Remove the CAP-BLANKING from each electrical connector and receptacle.
(d) Make sure that all the electrical connections are clean and in the correct condition.
(e) Put the oven (7) on the mounting rails (1).
(f) Carefully push the oven (7) into the galley and connect the electrical connector.
(g) Put the washers (4) in position and install the screws (6).
(h) TORQUE the screws (6) to between 0.79 and 0.57 m.daN (69.91 and 50.44 lbf.in )
. B. Installation of the Oven
(a) Remove the CAP-BLANKING from each electrical connector and receptacle.
(b) Make sure that all the electrical connections are clean and in the correct condition.
(c) Put the oven (3) on the mounting rails (1).
(d) Carefully push the oven (3) into the galley to connect the electrical connector.
(e) Install the screws (2).
(f) TORQUE the screws (2) to between 0.70 and 0.56 m.daN (61.95 and 49.56 lbf.in ).
(2) Install the oven (3) in aft galley G4B as follows:
(a) Put the bracket (4) in position and install the screws (5).
(b) TORQUE the screws (5) to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in ).
(c) Remove the CAP-BLANKING from each electrical connector and receptacle.
(d) Make sure that all the electrical connections are clean and in the correct condition.
(e) Put the oven (3) in position on the mounting rails (1).
(f) Carefully push the oven (3) into the galley to connect the electrical connector.
(g) Install the screws (6).
(h) TORQUE the screws (6) to between 0.39 and 0.34 m.daN (34.51 and 30.09 lbf.in ).
(i) Put the screen (7) in position and install the screws (8).
(j) TORQUE the screws (8) to between 0.16 and 0.14 m.daN (14.16 and 12.39 lbf.in ).
Subtask 25-35-19-420-050-LE ** ON A/C NOT FOR ALL WARNING:
SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1) Install the oven (3) in the forward galley and aft galley G3B as follows: (a) Remove the CAP-BLANKING from each electrical connector and receptacle.
(b) Make sure that all the electrical connections are clean and in the correct condition.
(c) Put the oven (3) on the mounting rails (1).
(d) Carefully push the oven (3) into the galley to connect the electrical connector.
(e) Install the screws (2).
(f) TORQUE the screws (2) to between 0.70 and 0.56 m.daN (61.95 and 49.56 lbf.in )
. (2) Install the oven (3) in aft galley G4B as follows:
(a) Put the bracket (4) in position and install the screws (5).
(b) TORQUE the screws (5) to between 0.20 and 0.16 m.daN (17.70 and 14.16 lbf.in )
. (c) Remove the CAP-BLANKING from each electrical connector and receptacle.
(d) Make sure that all the electrical connections are clean and in the correct condition.
(e) Put the oven (3) in position on the mounting rails (1).
(f) Carefully push the oven (3) into the galley to connect the electrical connector.
(g) Install the screws (6).
(h) TORQUE the screws (6) to between 0.39 and 0.34 m.daN (34.51 and 30.09 lbf.in )
. (i) Put the screen (7) in position and install the screws (8).
(j) TORQUE the screws (8) to between 0.16 and 0.14 m.daN (14.16 and 12.39 lbf.in )
. B. Installation of the Oven(s)
(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(3) Make sure that all the electrical connections are clean and in the correct condition.
(4) FOR [6475MM] (GALLEY LOC.I), [6480MM] (GALLEY LOC.III)
Install the oven(s) (3) in the related galley as follows:
(a) Put the oven(s) (3) in position on the mounting rails (1).
(b) Carefully push the oven(s) (3) into the galley and connect the electrical connector(s).
(c) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (2).
(d) Install the screws (2).
(e) TORQUE the screws (2) to between 0.20 and 0.18 m.daN (17.70 and 15.93 lbf.in ).
(5) FOR [6482MM] (GALLEY LOC.IV A/B)
Install the oven(s) (3) in the galley as follows:
(a) Put the oven(s) (3) in position on the mounting rails (1).
(b) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (5).
(c) Put the bracket(s) (4) in position and install the screws (5).
(d) TORQUE the screws (5) to between 0.20 and 0.18 m.daN (17.70 and 15.93 lbf.in ).
(e) Carefully push the oven(s) (3) into the galley and connect the electrical connector(s).
(f) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (6).
(g) Install the screws (6).
(h) TORQUE the screws (6) to between 0.40 and 0.34 m.daN (35.40 and 30.09 lbf.in ).
(i) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (8).
(j) Put the screen(s) (7) in position and install the screws (8).
(k) TORQUE the screws (8) to between 0.17 and 0.14 m.daN (15.04 and 12.39 lbf.in ).
(l) Clean the screen(s) (7), the heads of the screws (8) and the adjacent area.
(m) Apply Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) to the heads of the screws (8) and the screen(s) (7).
Subtask 25-35-19-860-062-A ** ON A/C NOT FOR ALL WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1) Prevent damage to the component interfaces and the adjacent area.(2) Remove the CAP-BLANKING from each electrical connector and receptacle.
(3) Make sure that all the electrical connections are clean and in the correct condition.
(4) FOR [6475MM] (GALLEY LOC.I), [6480MM] (GALLEY LOC.III)
Install the oven(s) (3) in the related galley as follows:
(a) Put the oven(s) (3) in position on the mounting rails (1).
(b) Carefully push the oven(s) (3) into the galley and connect the electrical connector(s).
(c) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (2).
(d) Install the screws (2).
(e) TORQUE the screws (2) to between 0.20 and 0.18 m.daN (17.70 and 15.93 lbf.in )
.(5) FOR [6482MM] (GALLEY LOC.IV A/B)
Install the oven(s) (3) in the galley as follows:
(a) Put the oven(s) (3) in position on the mounting rails (1).
(b) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (5).
(c) Put the bracket(s) (4) in position and install the screws (5).
(d) TORQUE the screws (5) to between 0.20 and 0.18 m.daN (17.70 and 15.93 lbf.in )
.(e) Carefully push the oven(s) (3) into the galley and connect the electrical connector(s).
(f) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (6).
(g) Install the screws (6).
(h) TORQUE the screws (6) to between 0.40 and 0.34 m.daN (35.40 and 30.09 lbf.in )
.(i) Apply Threadlocking Adhesive-- Medium strength - (Material No.05BAE1) to the threads of the screws (8).
(j) Put the screen(s) (7) in position and install the screws (8).
(k) TORQUE the screws (8) to between 0.17 and 0.14 m.daN (15.04 and 12.39 lbf.in )
.(l) Clean the screen(s) (7), the heads of the screws (8) and the adjacent area.
(m) Apply Silicone Adhesive Sealant-General Purpose One part legacy (Material No.06CMD9) to the heads of the screws (8) and the screen(s) (7).
C. At the applicable galley, on the galley control panel, remove the safety clip(s) and the tag(s), then close the circuit breaker(s) of the oven(s).
Subtask 25-35-19-710-053-A ** ON A/C NOT FOR ALL 5. Close-upSubtask 25-35-19-410-050-A ** ON A/C NOT FOR ALL
A. Close Access
(1) If the trolley(s) is (are) removed, install it (them).
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3) Make sure that the work area is clean and clear of tools and other items.
Subtask 25-35-19-410-050-J ** ON A/C NOT FOR ALL (1) If the trolley(s) is (are) removed, install it (them).
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3) Make sure that the work area is clean and clear of tools and other items.
A. Close Access
(1) If the trolley(s) is (are) removed, install it (them).
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3) Make sure that the work area is clean and clear of tools and other items.
Subtask 25-35-19-410-050-L ** ON A/C NOT FOR ALL (1) If the trolley(s) is (are) removed, install it (them).
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3) Make sure that the work area is clean and clear of tools and other items.
A. Close Access
(1) If the trolley(s) is (are) removed, install it (them).
(2) If the table(s) is (are) pulled out, push it (them) back.
(3) Close all doors.
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(5) Make sure that the work area is clean and clear of tools and other items.
Subtask 25-35-19-410-050-KG ** ON A/C NOT FOR ALL (1) If the trolley(s) is (are) removed, install it (them).
(2) If the table(s) is (are) pulled out, push it (them) back.
(3) Close all doors.
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(5) Make sure that the work area is clean and clear of tools and other items.
A. Close Access
(1) If the trolley(s) is (are) removed, install it (them).
(2) If the table(s) is (are) pulled out, push it (them) back.
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(4) Make sure that the work area is clean and clear of tools and other items.
Subtask 25-35-19-862-050-A ** ON A/C NOT FOR ALL (1) If the trolley(s) is (are) removed, install it (them).
(2) If the table(s) is (are) pulled out, push it (them) back.
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(4) Make sure that the work area is clean and clear of tools and other items.