Configuration of the Passenger Entertainment (Video) with the Programmable System Control Unit

TASK 23-36-00-600-002-A
Configuration of the Passenger Entertainment (Video) with the Programmable System Control Unit

ZONE: 200
FIN: 11MH ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)

3. Job Set-up
Subtask 23-36-00-861-052-A ** ON A/C NOT FOR ALL

A. Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).

Subtask 23-36-00-860-067-A ** ON A/C NOT FOR ALL

B. Open the applicable overhead stowage compartment(s).

Subtask 23-36-00-865-097-A ** ON A/C NOT FOR ALL

C. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	PES-VIDEO-CONTROL-VCC	21MH	C02
2000VU	PES-VIDEO-CONTROL-MAIN	20MH	C01

4. Procedure
Subtask 23-36-00-970-050-B ** ON A/C NOT FOR ALL

A. Configuration of the Quantity from the Tapping Units

ACTION	RESULT
1.On the System Control Unit (SCU) 11MH:	On the SCU 11MH:
push the MASTER POWER pushbutton switch.	the internal light of the MASTER POWER pushbutton switch comes on, all the LED come on while the SCU 11MH does the self test of the system, the green LED SYSTEM TEST/PASS comes on when the self test is completed.
	On the SCU 11MH, on the monitor: the PROGRAMMABLE PSCU page comes into view. NOTE: Wait for a minimum of 3 minutes after the SCU power-on, then continue with the procedure.
	the AUTO MODE selection page comes into view.
2.On the SCU 11MH, MODE SELECT area:	On the SCU 11MH, on the monitor:
push and hold the membrane switch for 5 seconds.	the MAINTENANCE MODE page comes into view.
3.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the '9' membrane switch four times,	the ENTER ID #:'9999' comes into view,
push the ENTER membrane switch.	the MAINTENANCE MODE selection page comes into view.
4.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item CONFIGURATION,	the cursor moves to CONFIGURATION,
push the ENTER membrane switch.	the CONFIGURATION selection page comes into view.
5.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item SVDU/MONITOR CONFIG,	the cursor moves to SVDU/MONITOR CONFIG,
push the ENTER membrane switch.	the SVDU/MONITOR CONFIG selection page comes into view.
6.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item SVDU CONFIG,	the cursor moves to SVDU CONFIG,
push the ENTER membrane switch.	the SVDU CONFIG selection page comes into view.
7.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item PREDEFINED CONFIG,	the cursor moves to PREDEFINED CONFIG,
push the ENTER membrane switch.	the SVDU CONFIG/ENTER SYDU TABLE #/(1-50) page comes into view.
8.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch for the selection of the table '20',	the item SVDU TABLE # '20' comes into view,
push the ENTER membrane switch.	This message comes into view: SVDU INITIALIZATION in PROGRESS XXX% COMPLETED
	When the initialization process is completed: on the SVDU CONFIG page these messages come into the view: SVDU INITIALIZATION COMPLETED CHAIN A:10 SVDU CHAIN B:10 SVDU
9.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the CLEAR membrane switch again and again until the AUTO MODE selection page comes into view.	the AUTO MODE selection page comes into view.
10.On the SCU 11MH:	On the SCU 11MH:
push the MASTER POWER pushbutton switch.	the internal light of the MASTER POWER pushbutton switch goes off. NOTE: Wait for a minimum of 10 seconds after the SCU power-off, then continue with the configuration.

Subtask 23-36-00-970-051-A ** ON A/C NOT FOR ALL

B. Configuration of the Programmable System Control-Unit

ACTION	RESULT
1.On the System Control Unit (SCU) 11MH:	On the SCU 11MH:
push the MASTER POWER pushbutton switch.	the internal light of the MASTER POWER pushbutton switch comes on, all the LED come on while the SCU 11MH does the self test of the system, the green LED SYSTEM TEST/PASS comes on when the self test is completed.
	On the SCU 11MH, on the monitor: the PROGRAMMABLE PSCU page comes into view. NOTE: Wait for a minimum of 3 minutes after the SCU power-on, then continue with the procedure.
	the AUTO MODE selection page comes into view.
2.On the SCU 11MH, MODE SELECT area:	On the SCU 11MH, on the monitor:
push and hold the membrane switch for 5 seconds.	the MAINTENANCE MODE page comes into view.
3.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the '9' membrane switch four times,	the ENTER ID #:'9999' comes into view,
push the ENTER membrane switch.	the MAINTENANCE MODE selection page comes into view.
4.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item CONFIGURATION,	the cursor moves to CONFIGURATION,
push the ENTER membrane switch.	the CONFIGURATION selection page comes into view.
5.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item PSCU CONFIG,	the cursor moves to PSCU CONFIG,
push the ENTER membrane switch.	the PSCU CONFIG selection page comes into view with this message: VTR1/BCS1 YES or VTR1/BCS1 NO
6.On the SCU 11MH, on the key pad: NOTE: If the VTR1/BCS1 YES message comes into view, continue at step 7.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item NO,	the cursor moves to NO,
push the SEL membrane switch,	NO is replaced with YES,
push the up or down arrow membrane-switch to move the cursor to the item VTR1/BCS1.	the cursor moves to VTR1/BCS1.
7.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the SEL membrane switch.	the PSCU CONFIG selection page comes into view with this message: VTR2/BCS2 YES or VTR2/BCS2 NO
8.On the SCU 11MH, on the key pad: NOTE: If the VTR2/BCS2 YES message comes into view, continue at step 9.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item NO,	the cursor moves to NO,
push the SEL membrane switch,	NO is replaced with YES,
push the up or down arrow membrane-switch to move the cursor to the item VTR2/BCS2.	the cursor moves to VTR2/BCS2.
9.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the SEL membrane switch.	the PSCU CONFIG selection page comes into view with this message: VTR3/BCS3 NO or VTR3/BCS3 YES
10.On the SCU 11MH, on the key pad: NOTE: If the VTR3/BCS3 NO message comes into view, continue at step 11.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item YES,	the cursor moves to YES,
push the SEL membrane switch,	YES is replaced with NO,
push the up or down arrow membrane-switch to move the cursor to the item VTR3/BCS3.	the cursor moves to VTR3/BCS3.
11.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the SEL membrane switch.	the PSCU CONFIG selection page comes into view with this message: VTR4/BCS4 NO or VTR4/BCS4 YES
12.On the SCU 11MH, on the key pad: NOTE: If the VTR4/BCS4 NO message comes into view, continue at step 13.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item YES,	the cursor moves to YES,
push the SEL membrane switch,	YES is replaced with NO,
push the up or down arrow membrane-switch to move the cursor to the item VTR4/BCS4.	the cursor moves to VTR4/BCS4.
13.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the SEL membrane switch.	the PSCU CONFIG selection page comes into view with this message: AMUX NO or AMUX YES
14.On the SCU 11MH, on the key pad: NOTE: If the AMUX NO message comes into view, continue at step 15.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item YES,	the cursor moves to YES,
push the SEL membrane switch,	YES is replaced with NO,
push the up or down arrow membrane-switch to move the cursor to the item AMUX.	the cursor moves to AMUX.
15.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the SEL membrane switch.	the PSCU CONFIG page comes into view with this message: PRAM YES or PRAM NO
16.On the SCU 11MH, on the key pad: NOTE: If the PRAM YES message comes into view, continue at step 17.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item NO,	the cursor moves to NO,
push the SEL membrane switch,	NO is replaced with YES,
push the up or down arrow membrane-switch to move the cursor to the item PRAM.	the cursor moves to PRAM.
17.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the SEL membrane switch.	the PSCU CONFIG page comes into view with this message: AIRSHOW YES or AIRSHOW NO
18.On the SCU 11MH, on the key pad: NOTE: If the AIRSHOW YES message comes into view, continue at step 19.	On the SCU 11MH, on the monitor:
push the up or down arrow membrane-switch to move the cursor to the item NO,	the cursor moves to NO,
push the SEL membrane switch,	NO is replaced with YES.
push the up or down arrow membrane-switch to move the cursor to the item AIRSHOW.	the cursor moves to AIRSHOW.
19.On the SCU 11MH, on the key pad:	On the SCU 11MH, on the monitor:
push the ENTER membrane switch.	on the PSCU CONFIG page these messages come into the view: COMPLETED PLEASE CYCLE POWER
20.On the SCU 11MH:	On the SCU 11MH:
push the MASTER POWER pushbutton switch.	the internal light of the MASTER POWER pushbutton switch goes off.

5. Close-up
Subtask 23-36-00-410-055-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Close the applicable overhead stowage compartment(s).

Subtask 23-36-00-862-052-A ** ON A/C NOT FOR ALL

B. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.03.31 23:14:12 UTC