Operational Test of the Radio Management Panel (RMP)

TASK 23-13-00-710-001-A
Operational Test of the Radio Management Panel (RMP)

WARNING: MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT. UNWANTED ELECTRICAL POWER CAN BE DANGEROUS.

NOTE: You can do this test in the hangar.

ZONE: 210

1. Reason for the Job
To do a check of the dialog between the Radio Management Panels (RMPs).
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD

B. Referenced Information

REFERENCE	DESIGNATION
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)

3. Job Set-up
Subtask 23-13-00-861-050-A

A. Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002)

Subtask 23-13-00-865-050-A

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
49VU	COM/RMP/1	2RG1	G10
49VU	COM/VHF/1	2RC1	G09
121VU	COM NAV/RMP/2	2RG2	L02
** ON A/C NOT FOR ALL
121VU	COM NAV/RMP/3	2RG3	L03

4. Procedure
Subtask 23-13-00-710-050-A ** ON A/C NOT FOR ALL

A. Operational Test of the Radio Management

ACTION	RESULT
1.On the RMP1:
Set the ON/OFF selector switch to ON.	The RMP shows the last frequencies and the last function used.
Push the VHF1 pushbutton switch.	The green LED on this pushbutton switch comes on.
In the STBY/CRS display window, with the dual selector knob, set the frequency of a station that transmits.
Start this frequency. To do this, push the transfer pushbutton switch (double arrow) between the two windows.	In the ACTIVE display window, the frequency set comes into view.
2.On the RMP2:
Set the ON/OFF selector switch to ON.	The RMP shows the last frequencies and the last function used.
Push the VHF1 pushbutton switch.	The ACTIVE display window shows the same frequencies as the RMP1. The green LED on this pushbutton switch comes on. On the RMP1 and the RMP2: The SEL indicator light (amber LED) is on.
In the STBY/CRS display window, set a new frequency with the dual selector knob.
Start this frequency. To do this, push the transfer pushbutton switch (double arrow) between the two windows.	In the ACTIVE display window, the frequency set comes into view.

Subtask 23-13-00-710-050-B ** ON A/C NOT FOR ALL

A. Operational Test of the Radio Management

ACTION	RESULT
1.On the RMP1: Set the ON/OFF switch to ON.	The RMP1 shows the last frequencies and the last function used.
2.On the RMP1: Push the VHF1 pushbutton switch.	On the RMP1: The green LED on the VHF1 pushbutton switch comes on (it does not come on if the last function used was the VHF1 function).
3.On the RMP1: In the right window, with the dual selector knob, set the frequency of a station that transmits.
4.On the RMP1: Start the frequency set. To do this, push the pushbutton switch (double arrow) between the two windows.	On the RMP1: In the left window, the frequency set comes into view.
5.On the RMP2 and the RMP3: Set the ON/OFF switch to ON.	The RMP2 and 3 show the last frequencies and the last functions used.
6.On the RMP2 and the RMP3: Push the VHF1 pushbutton switch.	On the RMP2 and the RMP3: The left window shows the same frequency as the RMP1 The green LED on the VHF1 pushbutton switch comes on. On the RMP1, the RMP2 and the RMP3: The SEL indicator light (amber LED) is on.
7.On the RMP2: In the right window, set a new frequency with the dual selector knob.
8.On the RMP2: Start the frequency set. To do this, push the pushbutton switch (double arrow) between the two windows.	On the RMP2: In the left window, the frequency set comes into view. On the RMP1 and the RMP3: The left window shows the same frequency as on the RMP2.
9.On the RMP3: In the right window, set a new frequency with the dual selector knob.
10.On the RMP3: Start the frequency set. To do this, push the pushbutton switch (double arrow) between the two windows.	On the RMP3: In the left window, the frequency set comes into view. On the RMP1 and the RMP2: The left window shows the same frequency as on the RMP3.

5. Close-up
Subtask 23-13-00-860-050-A

A. Put the aircraft back to its initial configuration.
(1) On the RMPs, set the ON/OFF selector switch to OFF.
(2) De-energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-862-002).

[Rev.10 from 2021] 2026.04.01 05:21:20 UTC