Removal of the Throttle Control Artificial Feel Unit [IAE]

TASK 76-11-17-000-041-A
Removal of the Throttle Control Artificial Feel Unit

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	CAP - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
98DNSA20206080	1	RIGGING PIN

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
811

C. Referenced Information

REFERENCE	DESIGNATION
TASK 22-82-12-000-001-A	Removal of the Multipurpose Control & Display Unit (MCDU)
TASK 23-13-13-000-001-A	Removal of the Radio Management Panel (RMP)
TASK 23-51-12-000-001-A	Removal of the Audio Control Panel (ACP)
TASK 34-41-12-000-001-A	Removal of the Weather-Radar Control Unit
TASK 34-52-12-000-001-A	Removal of the ATC/TCAS Control Unit
Panels 111VU and 112VU
Ventilation Plates and Clamps
Throttle Control Rigging
Artificial Feel Unit

3. Job Set-up
Subtask 76-11-17-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Put a WARNING NOTICE(S) in the cockpit to tell persons not to move:

the throttle control levers
the slat and flap control levers.

(2) On the panel 50VU:

Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
Install a WARNING NOTICE(S).

(3) On the panel 115VU:

Put a WARNING NOTICE(S) to tell persons not to start the engine 1(2).

Subtask 76-11-17-865-053-A ** ON A/C NOT FOR ALL

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
49VU	FLIGHT CONTROLS/SEC1/NORM/SPLY	21CE1	B08
49VU	LIGHTING/EMER LT/CKPT/DOME	1LE	H08
105VU	FLT CTL/SEC1/STBY SPLY	22CE	B01
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	ENGINE/IGN/ENG2/SYS A BAT	2JH2	P40
121VU	ENGINE/IGN/ENG1/SYS A BAT	2JH1	P39
121VU	FLIGHT CONTROLS/SEC3/SPLY	21CE3	Q19
121VU	FLIGHT CONTROLS/SEC2/SPLY	21CE2	Q18
122VU	LIGHTING/INSTL LT/MAIN INST/PNL AND/PED	4LF	Y04
122VU	LIGHTING/FLOOD/CTR INST/PNL	2LE	Z04

Subtask 76-11-17-869-051-A ** ON A/C NOT FOR ALL

C. Make sure that the throttle control levers are at idle (0 deg.TLA).

Subtask 76-11-17-010-053-A ** ON A/C NOT FOR ALL

D. Open the access door 811.

Subtask 76-11-17-941-052-A ** ON A/C NOT FOR ALL

E. Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE.

Subtask 76-11-17-010-054-A ** ON A/C NOT FOR ALL

F. Remove for Access.
(1) Remove the Multipurpose Control and Display Units 3CA1 and 3CA2 (Ref. AMM TASK 22-82-12-000-001).
(2) Remove the Radio Management Panels 1RG1 and 1RG2 (Ref. AMM TASK 23-13-13-000-001).
(3) Remove the Audio Control Panels 2RN1 and 2RN2 (Ref. AMM TASK 23-51-12-000-001).
(4) Remove the Weather Radar Control Unit 3SQ (Ref. AMM TASK 34-41-12-000-001).
(5) Remove the ATC Control Unit 3SH (Ref. AMM TASK 34-52-12-000-001).
(6) Remove the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU:

Panels 111VU and 112VU ** ON A/C NOT FOR ALL

NOTE: The removal procedure is the same for the FLOOD LT/INTEG LT panel 111VU and FLOOD LT panel 112VU.

(a) Release the fasteners of the panel (1) and disengage the panel (1) from its housing.
(b) Disconnect the connector (3) from the panel (1).
(c) Remove the panel (1).
(d) Put CAP - BLANKING on the connectors (2) and (3).
(7) Remove the screws (7).
(8) Remove the ventilation plates (8).
(9) Disconnect the clamps (9).
(10) Remove the screws (6) and the washers (5).

Ventilation Plates and Clamps ** ON A/C NOT FOR ALL

(11) Remove the plates (4) and (10).

4. Procedure
Subtask 76-11-17-480-050-A ** ON A/C NOT FOR ALL

A. Install the rigging pin 98DNSA20206080 RIGGING PIN (11) in the throttle control unit

Throttle Control Rigging ** ON A/C NOT FOR ALL

Subtask 76-11-17-020-052-A ** ON A/C NOT FOR ALL

B. Removal of the Throttle Control Artificial Feel Unit:
(1) Remove and discard the 4 cotter pins (13)

Artificial Feel Unit ** ON A/C NOT FOR ALL

(2) Remove the 4 nuts (14), the 4 washers (15) and the 4 bolts (17). Make sure that the 4 bushes (16) stay bonded.
(3) Remove the rods (27).
(4) Remove and discard the 4 cotter pins (18).
(5) Remove the 2 nuts (19), the 2 washers (20) and the 2 bolts (26). Make sure that the 2 bushes (25) stay bonded.
(6) Remove the 2 nuts (21), the 2 washers (22) and the 2 bolts (24).
(7) Remove the throttle control artificial feel unit (23).

[Rev.10 from 2021] 2026.04.01 03:15:44 UTC